View source for Flywheel energy storage

[[Image:G2 front2.jpg|right|thumb|250px|'''NASA G2 Flywheel''' ]]

'''Flywheel Energy Storage''' (FES) works by accelerating a rotor to a very high speed and maintaining the energy in the system as inertial energy.  Commercially available FES systems are used for small [[Uninterruptible power supply|uninterruptible power systems]]. The rotors normally operate at 4000 RPM or less and are made of metal. Advanced [[flywheel]]s are made of high strength carbon-composite filaments that spin at speeds from 20,000-100,000 RPM in a vacuum enclosure. [[Magnetic bearing]]s are necessary since [[friction]] in conventional [[bearings|mechanical bearings]] are directly proportional to speed and at such speeds, it would be high enough to cause such a great energy loss as to defeat its purpose of energy storage. Quick charging is done in less than 15 minutes. Long lifetimes of most flywheels, plus high [[energy density|energy densities]] (~ 130 Wh/kg) and large maximum power outputs are positive attributes. The energy efficiency (''ratio of energy out per energy in'') of flywheels can be as high as 90%. Since FES can store and release power quickly, they have found a niche providing pulsed power.  

== Main components ==

[[Image:Flywheel 2004 sm.jpg|right|thumb|200px|'''Internal Flywheel Components''']]

A typical system consists of [[rotor]] suspended by [[bearing]]s inside a [[vacuum]] chamber to reduce [[friction]], connected to a combination [[electric motor]]/[[electric generator]]. On larger systems, the bearings are magnetic.  The rotors are generally made of steel on smaller systems but large systems use high-tensile-strength fibers (such as [[carbon fiber]]s) embedded in [[epoxy]] [[resin]]s, or some other high-strength [[composite material]].  Energy is stored by using an electric motor to increase the speed of the spinning flywheel. The system releases its energy by using the [[momentum]] of the flywheel to power the motor/generator.

== Physical characteristics ==
[[Image:Nasarotor.jpg|right|thumb|150px|'''Metal Flywheel Rotor''' ]]
Energy is stored in the rotor in proportion to its momentum, but the square of the angular momentum.  The [[kinetic energy]] stored in a rotating flywheel is:

:<math>E_k=\frac{1}{2}\cdot I\cdot \omega^2</math>
where 
:<math> \omega </math> is the [[angular velocity]], and
:<math> I </math> is the [[moment of inertia]] of the [[mass]] about the center of rotation.

* The moment of inertia for a solid-cylinder is <math>I_z = \frac{1}{2} mr^2</math>,
* for a thin-walled cylinder is <math>I = m r^2 \,</math>,
* and for a thick-walled cylinder is <math>I = \frac{1}{2} m({r_1}^2 + {r_2}^2)</math>.
where ''m'' denotes mass, and ''r'' denotes a radius. More information can be found at [[list of moments of inertia]]

The amount of energy that can safely be stored in the rotor depends on the point at which the rotor will warp or shatter. The [[Hoop stress]] on the rotor is a major consideration in the design of a flywheel energy storage system.

{{accuracy}}

:<math> \sigma_t = \rho r^2 \omega^2 \ </math>
where
:<math> \sigma_t </math> is the tensile stress on the rim of the cylinder
:<math> \rho </math> is the density of the cylinder
:<math> r </math> is the radius of the cylinder, and
:<math> \omega </math> is the [[angular velocity]] of the cylinder.

== Applications ==
In the [[1950s]] flywheel-powered buses, known as [[gyrobus]]es, were used in [[Yverdon]], [[Switzerland]], and there is ongoing research to make flywheel systems that are smaller, lighter, cheaper, and have a greater capacity.  It is hoped that flywheel systems can replace conventional chemical batteries for mobile applications, such as for electric vehicles.  Proposed flywheel systems would eliminate many of the disadvantages of existing battery power systems, such as low capacity, long charge times, heavy weight, and short usable lifetimes.  Flywheel systems have also been used experimentally in small [[electric locomotive]]s for shunting or [[switcher|switching]].

In the [[1980s]] Soviet engineer [[Nourbey Gulia]] had been working on flywheel energy storage. His work resulted in many original solutions for wheel suspension, sealing the vacuum chamber, rotation rate decline compensator and hydraulic transmission. However, the primary advance was the composite flywheel capable of rotation rates exceeding 40,000 rpm, running for up to a week when not loaded, and resistant to explosive destruction. Gulia's "super flywheels" were tightly wound of metal or plastic tape. These had tensile strength higher than that of molded steel, and in the case of failure simply unwound inside the chamber, filling it and grinding to a stop. Gulia's first wheels were made of steel tape, but the latest models used Kevlar filament, wound not unlike a bobbin of thread.

Flywheel power storage systems in current production ([[2001]]) have storage capacities comparable to batteries and faster discharge rates.  They are mainly used to provide load leveling for large battery systems, such as an [[uninterruptible power supply]].  Developers of such flywheel energy storage systems include Hitec Power Protection, Active Power, AFS Trinity and Beacon Power.

A long-standing niche market for flywheel power systems is facilities where
circuit-breakers and similar devices are tested: even a small household
circuit-breaker may be rated to interrupt a current of 10,000 or more
amps, and larger units may be have interrupting ratings of 100,000 or
1,000,000 amps.  Obviously the enormous transient loads produced by
deliberately forcing such devices to demonstrate their ability to interrupt
simulated short circuits would have unacceptable effects on the local
grid if these tests were done directly off building power.  So typically
such a laboratory will have several large motor-generator sets, which
can be spun-up to speed over some minutes; then the motor is disconnected
before a circuit-breaker is tested.

== Advantages and disadvantages ==

Flywheels are not affected by temperature changes as are chemical [[battery (electricity)|batteries]], nor do they suffer from [[memory effect]]. Moreover, they are not as limited in the amount of energy they can hold. They are also less potentially damaging to the environment, being made of largely inert or benign materials. Another advantage of flywheels is that by a simple measurement of the rotation speed it is possible to know the exact amount of energy stored. However, use of flywheel accumulators is currently hampered by the danger of explosive shattering of the massive wheel due to overload. 

One of the primary limits to flywheel design is the [[tensile strength]] of the material used for the rotor.  Generally speaking, the stronger the disc, the faster it may be spun, and the more energy the system can store.  When the tensile strength of a flywheel is exceeded the flywheel will shatter, releasing all of its stored energy at once;  this is commonly referred to as "flywheel explosion" since wheel fragments can reach kinetic energy comparable to that of a bullet. Consequently, traditional flywheel systems require strong containment vessels as a safety precaution, which increases the total mass of the device. Fortunately, composite materials tend to disintegrate quickly once broken, and so instead of large chunks of high-velocity shrapnel one simply gets a containment vessel filled with red-hot sand (still, many customers of modern flywheel power storage systems prefer to have them embedded in the ground to halt any material that might escape the containment vessel).  Gulia's tape flywheels did not require a heavy container and reportedly could be rewound and reused after a tape fracture.

When used in vehicles, flywheels also act as [[gyroscope]]s, since their [[angular momentum]] is typically of a similar order of magnitude as the forces acting on the moving vehicle. This property may be detrimental to the vehicle's  handling characteristics while turning. On the other hand, this property could be utilised to improve stability in curves. Two externally joined flywheels spinning synchronously in opposite directions would have a total angular momentum of zero and no gyroscopic effect.

== Bearings ==

The expense of refrigeration led to the early dismissal of low temperature superconductors for use in magnetic bearings.  [[high-temperature superconductors|High-temperature]] [[superconductor]] ([[high-temperature superconductors|HTSC]]) bearings however may be economic and could possibly extend the time energy could be stored economically.  Hybrid bearing systems are most likely to see use first.  HTSC bearings have historically had problems providing the lifting forces necessary for the larger designs, but can easily provide a stabilizing force.  Therefore, in hybrid bearings, permanent magnets support the load and HTSC are used to stabilize it. The reason superconductors can work well stabilizing the load is because they are good [[diamagnets]]. In hybrid-bearing systems, a conventional magnet levitates the rotor, but the high temperature superconductor keeps it stable.  If the rotor tries to drift off center, a restoring force due to [[flux pinning]] restores it. This is known as the magnetic stiffness of the bearing. Rotational axis vibration can occur due to low stiffness and damping, which are inherent problems of superconducting magnets, preventing the use of completely superconducting magnetic bearings for flywheel applications. 
 
Since flux pinning is the important factor for providing the stabilizing and lifting force, the HTSC can be made much easier for FES than for other uses.  HTSC powders can be formed into arbitrary shapes so long as flux pinning is strong.  An ongoing challenge that has to be overcome before superconductors can provide the full lifting force for a FES system is finding a way to suppress the decrease of levitation force and the gradual fall of rotor during operation caused by the flux creep of SC material.

Parasitic losses such as friction, [[hysteresis]] and [[eddy current]] losses of both magnetic and conventional bearings in addition to refrigerant costs can limit the economical energy storage time for flywheels.  However, further improvements in [[superconductor]]s may help eliminate eddy current losses in existing magnetic bearing designs as well as raise overall operating temperatures. Even without such improvements, however, modern flywheels can have a zero-load rundown time measurable in years.

== Flywheel energy storage companies ==
* Active Power Inc. http://www.activepower.com/
* AFS Trinity Power Corporation http://afstrinity.com/ ( [http://afstrinity.com/other-facts-faqs.html "Flywheel facts and FAQs"] )
* Beacon Power Corporation http://beaconpower.com/ ( [http://beaconpower.com/products/EnergyStorageSystems/flywheels.htm "About Flywheels"] )

==References==
* Sheahen, T., P.  (1994).  Introduction to High-Temperature Superconductivity.  Plenum Press, New York.  pp. 76-78, 425-431.
* El-Wakil, M., M.  (1984).  Powerplant Technology.  McGraw-Hill, pp. 685-689.
* Koshizuka, N., Ishikawa, F.,Nasu, H., Murakami, M., Matsunaga, K., Saito, S., Saito, O., Nakamura, Y., Yamamoto, H., Takahata, R., Itoh, Y., Ikezawa, H., Tomita, M.  (2003).  Progress of superconducting bearing technologies for flywheel energy storage systems.  Physica C 386, pp. 444–450.
* Wolsky, A., M.  (2002).  The status and prospects for flywheels and SMES that incorporate HTS.  Physica C 372–376, pp. 1495–1499.
* Sung, T., H., Han, S., C., Han, Y., H., Lee, J., S., Jeong, N., H., Hwang, S., D., Choi, S.,  K.  (2002). Designs and analyses of flywheel energy storage systems using high-Tc superconductor bearings.  Cryogenics V. 42, pp. 357–362.
* http://www.parcon.uci.edu/OLD_WEBSITE/paper/eeenergy.htm
* http://infoserve.sandia.gov/cgi-bin/techlib/access-control.pl/1997/970443.pdf
* http://www.wtec.org/loyola/scpa/04_02.htm
* [http://space-power.grc.nasa.gov/ppo/highlights/ NASA Power and Propulsion Office: Highlights and Accomplishments]
* [http://www.llnl.gov/str/pdfs/04_96.2.pdf Development at LLNL using passive maglev to levetate the rotor]
*[http://rpm2.8k.com/basics.htm Basics of flywheel batteries]
*[http://www.vyconenergy.com More on flywheels]

== See also ==

*[[Grid energy storage]]
*[[Flywheel]]
*[[Magnetic bearing]]

{{Energy Development and Use}}
{{Sustainability and energy development group}}

[[Category:Energy storage]]

[[es:batería inercial]]