Ćuk converter

Comparison of non-isolated switching DC-to-DC converter topologies: Buck, Boost, Buck-Boost, Ćuk. The input is left side, the output with load is right side. The switch is typically a MOSFET, IGBT, or BJT transistor.

The Ćuk converter (Serbo-Croatian: [tɕûːk], English: /ˈtʃuːk/) is a type of buck-boost converter with low ripple current. A Ćuk converter can be seen as a combination of boost converter and buck converter, having one switching device and a mutual capacitor, to couple the energy.

Similar to the buck-boost converter with inverting topology, the output voltage of non-isolated Ćuk converter is typically inverted, with lower or higher values with respect to the input voltage. While DC-to-DC converters usually use the inductor as a main energy-storage component, the Ćuk converter instead uses the capacitor as the main energy-storage component. It is named after Slobodan Ćuk of the California Institute of Technology, who first presented the design.

Non-isolated Ćuk converter

There are variations on the basic Ćuk converter. For example, the coils may share a single magnetic core, which drops the output ripple, and adds efficiency. Because the power transfer flows continuously via the capacitor, this type of switcher has minimized EMI radiation. The Ćuk converter allows energy to flow bidirectionally by using a diode and a switch.

Operating principle

A non-isolated Ćuk converter comprises two inductors, two capacitors, a switch (usually a transistor), and a diode. Its schematic can be seen in figure 1. It is an inverting converter, so the output voltage is negative with respect to the input voltage.

The main advantage of this converter is the continuous currents at the input and output of the converter.  The main disadvantage is the high current stress on the switch.

Fig. 1: Cuk converter circuit diagram.

The capacitor C₁ is used to transfer energy. It is connected alternately to the input and to the output of the converter via the commutation of the transistor and the diode (see figures 2 and 3).

The two inductors L₁ and L₂ are used to convert respectively the input voltage source (V_s) and the output voltage (V_o) into current sources. At a short time scale, an inductor can be considered as a current source as it maintains a constant current. This conversion is necessary because if the capacitor were connected directly to the voltage source, the current would be limited only by the parasitic resistance, resulting in high energy loss. Charging a capacitor with a current source (the inductor) prevents resistive current limiting and its associated energy loss.

As with other converters (buck converter, boost converter, buck–boost converter) the Ćuk converter can operate in either continuous or discontinuous current mode. However, unlike these converters, it can also operate in discontinuous voltage mode (the voltage across the capacitor drops to zero during the commutation cycle).

Continuous mode

Fig. 2: The two operating states of a non-isolated Ćuk converter.

In steady state, the energy stored in each inductor has to remain the same at the beginning and at the end of a commutation cycle. The energy in an inductor is given by:

$E={\frac {1}{2}}LI^{2}.$

This implies that the current through each inductor has to be the same at the beginning and the end of the commutation cycle. As the evolution of the current through an inductor is related to the voltage across it:

$V_{L}=L{\frac {dI}{dt}},$

it can be seen that the average value of each inductor's voltage over a commutation period has to be zero to satisfy the steady-state requirements. (Another way to see this is to recognize that the average voltage across any inductor must be zero lest its current rise without limit.)

If we consider that the capacitors C₁ and C₂ are large enough for the voltage ripple across them to be negligible, the inductor voltages become:

• in the off-state, inductor L₁ is connected in series with V_s and C₁ (see figure 2). Therefore ${\textstyle V_{L1}=V_{s}-V_{C1}}$. As the diode D is forward biased (we consider zero voltage drop), L₂ is directly connected to the output capacitor. Therefore $V_{L2}=V_{o}$
• in the on-state, inductor L₁ is directly connected to the input source. Therefore ${\textstyle V_{L1}=V_{s}}$. Inductor L₂ is connected in series with C and the output capacitor, so $V_{L2}=V_{o}+V_{C}$

Fig. 3: The two operating states of a non-isolated Ćuk converter. The diode and the switch are simplified as either a short circuit when they are on or by an open circuit when they are off. When in the off-state, the capacitor C is charged by the input source through the inductor L₁. When in the on-state, the capacitor C transfers the energy to the output capacitor through the inductance L₂.

The converter operates in on state from ${\textstyle t=0}$ to ${\textstyle t=DT}$ (D is the duty cycle), and in off state from D·T to T (that is, during a period equal to ${\textstyle (1-D)T}$). The average values of V_L1 and V_L2 are therefore:

${\bar {V}}_{L1}=D\cdot V_{s}+\left(1-D\right)\cdot \left(V_{s}-V_{C}\right)=\left(V_{s}-(1-D)\cdot V_{C}\right)$

${\bar {V}}_{L2}=D\left(V_{o}+V_{C}\right)+\left(1-D\right)\cdot V_{o}=\left(V_{o}+D\cdot V_{C}\right)$

As both average voltage have to be zero to satisfy the steady-state conditions, using the last equation we can write:

$V_{C}=-{\frac {V_{o}}{D}}$

So the average voltage across L₁ becomes:

${\bar {V}}_{L1}=\left(V_{s}+(1-D)\cdot {\frac {V_{o}}{D}}\right)=0$

Which can be written as:

${\frac {V_{o}}{V_{s}}}=-{\frac {D}{1-D}}$

It can be seen that this relation is the same as that obtained for the buck–boost converter.

Discontinuous mode

Like all DC/DC converters, Ćuk converters rely on the ability of the inductors in the circuit to provide continuous current, in much the same way a capacitor in a rectifier filter provides continuous voltage. If this inductor is too small or below the "critical inductance", then the inductor current slope will be discontinuous where the current goes to zero. This state of operation is usually not studied in much depth as it is generally not used beyond a demonstrating of why the minimum inductance is crucial, although it may occur when maintaining a standby voltage at a much lower current than the converter was designed for.

The minimum inductance is given by:

$L_{1}min={\frac {(1-D)^{2}R}{2Df_{s}}}$

Where $f_{s}$ is the switching frequency.

Isolated Ćuk converter

Coupled inductor isolated Ćuk converter.

Integrated magnetics Ćuk converter.

For isolated version of Ćuk converter, an AC transformer and an additional capacitor must be added. Because the isolated Ćuk converter is isolated, the output-voltage polarity can be chosen freely.

Isolated Ćuk converter with gapless AC transformer.

As the non-isolated Ćuk converter, the isolated Ćuk converter can have an output voltage magnitude that is either greater than or less than the input voltage magnitude, even with a 1:1 AC transformer. However, the turns ratio can be controlled to reduce device stress on the input side. Additionally, the parasitic elements of the transformer, namely leakage inductance and magnetizing inductance can be used to modify the circuit into a resonant converter circuit which has much improved efficiency.

Related structures

Inductor coupling

Instead of using two discrete inductor components, many designers implement a coupled inductor Ćuk converter, using a single magnetic component that includes both inductors on the same core. The transformer action between the inductors inside that component gives a coupled inductor Ćuk converter with lower output ripple than a Ćuk converter using two independent discrete inductor components.

Zeta converter

A zeta converter is a non-isolated, non-inverting, buck-boost power supply topology.

Single-ended primary-inductor converter (SEPIC)

Main article: SEPIC converter

A SEPIC converter is able to step-up or step-down the voltage.

Patents

• US Patent 4257087, filed in 1979, "DC-to-DC switching converter with zero input and output current ripple and integrated magnetics circuits", inventor Slobodan Ćuk.
• US Patent 4274133, filed in 1979, "DC-to-DC Converter having reduced ripple without need for adjustments", inventor Slobodan Ćuk and R. D. Middlebrook.
• US Patent 4184197, filed in 1977, "DC-to-DC switching converter", inventor Slobodan Ćuk and R. D. Middlebrook.

Further reading

• Power Electronics, Vol. 4: State-Space Averaging and Ćuk Converters; Ćuk Slobodan; 378 pages; 2016; ISBN 978-1519520289.

External links

• Topology Background