Headshunt: Difference between revisions

Content deleted Content added

Inline

Latest revision as of 20:06, 11 November 2024

A headshunt (or escape track in the United States) is a short length of track provided to release locomotives at terminal platforms, or to allow shunting to take place clear of main lines.

Terminal headshunt

A 'terminal headshunt' is a short length of track that allows a locomotive to uncouple from its train, move forward, and then run back past it on a parallel track. Such headshunts are typically installed at a terminal station to allow the locomotive of an arriving train to move to the opposite end of (in railway parlance, 'run around') its train so that it can then haul the same train out of the station in the other direction (assuming, of course, that it is a locomotive equipped to run in either direction; for locomotives that only operate in one direction, a wye or turntable needs to be provided to physically turn the engine around, as well as a run-around track).

Reversing headshunt

Found primarily on metro systems, rapid transit light rail networks, and tramways, a 'reversing headshunt' allows certain trains or trams to change direction, even on lines with high traffic flow, whilst others continue through the station.

Shunting neck

The term headshunt may also refer to shunting neck or 'shunt spur': a short length of track laid parallel to the main line to allow a train to shunt back into a siding or rail yard without occupying the main running-line.^{[citation needed]}

Run round

A run round loop (or run-around loop) is a track arrangement that enables a locomotive to attach to the opposite end of the train. It is commonly used to haul wagons onto a siding, or at a terminal station to prepare for a return journey.^[1] This process is known as "running round a train".^[2]

Although a common procedure for passenger trains when the majority of them were locomotive-hauled, the maneuver is now becoming rarer on public service railways.^{[citation needed]} Increased use of multiple unit and push-pull passenger services avoids the requirement for dedicated track and the need for railway staff to detach and reattach the locomotive at track level.^{[citation needed]} However, on heritage railways run-round loops are still usually more or less necessary at each end of the running line, partly because train services are usually locomotive-hauled, and partly because the run-round operation gives added interest to visitors. This practice is still very common on Intercity services in Victoria, Australia.

Runaround tracks are used in freight rail service in order to back cars into spurs or to change directions to keep the locomotive at the front of the train for transport. In this case the runaround track must be as long as the longest set of cars that would be pulled. The locomotive leaves the cars on the runaround track or the main line, goes around, and hooks up to the other end of the train. It can then reverse the cars into a spur.

Examples

Stations which used to have run-rounds include:

United Kingdom
- Edinburgh Waverley railway station; The terminal platforms of this station featured locomotive release roads between two main platforms, connected by a three-way point to the crossover from each platform line.^[3]^[4]^[5]^[6] The same arrangement of a three-way point on a central release road was also installed at the now closed stations:
- St Ives railway station
- Matlock Riverside railway station, now closed
- Birmingham Moor Street. This station is on a confined site, so to save space the platform lines were equipped with traversers to allow locomotives to run round via the adjacent platform line (platforms 1 & 2) or an adjacent loop (platform 3).^[16]^[17]^[18]
- Withernsea, the terminal station on the now closed Hull and Holderness Railway. At this station, instead of a crossover or points the run round loop was accessed from a turntable at the end of the platform line and run round loop.^[19]^[20] There was a similar arrangement at Ventnor and Bembridge railway stations on the Isle of Wight.

Turntable and run round loop at Withernsea
Leeds Central station showing the release crossovers

Australia
- Murwillumbah railway station, now closed
- Toronto railway station, New South Wales, now closed
- Cronulla railway station, had run-round, but never had locomotives
- Newcastle railway station, New South Wales, now closed; run-round on Platform 1&2, not on Platform 3&4

Stations which still have run-rounds include:

United Kingdom
Germany
- Hagen Hauptbahnhof
Australia (all in regular loco-hauled passenger use unless otherwise indicated)
- Central railway station, Sydney
- Albury railway station
- Canberra railway station (run-around not in regular use)
- Southern Cross railway station (Melbourne)
- Shepparton railway station
- Bairnsdale railway station
- Geelong railway station
- South Geelong railway station
- Marshall railway station
- Warrnambool railway station
- Swan Hill railway station
- Seymour railway station
- Roma Street railway station (Brisbane) (not sure if run-around in use)
- Toowoomba railway station
- Charleville railway station
- Rockhampton railway station
- Longreach railway station
- Townsville railway station
- Mount Isa railway station
- Cairns railway station
- Kuranda railway station
- Adelaide Parklands Terminal
- Public Transport Centre (East Perth terminal)
- Darwin railway station

No loop

If a terminal station does not have a run-round loop trains are restricted to multiple units or Top and Tail trains.^{[citation needed]}

References

^ Jackson, Alan A. (2006). The Railway Dictionary (4th ed.). Sutton Publishing Ltd. p. 298. ISBN 0-7509-4218-5.
^ Ellis, Iain (2006). Ellis' British Railway Engineering Encyclopaedia. Lulu.com. p. 307. ISBN 978-1-8472-8643-7.
^ "View map: Edinburghshire III.8 (Edinburgh) - Ordnance Survey 25 inch 2nd and later editions, Scotland, 1892-1949". maps.nls.uk.
^ Edinburgh Waverley station - NBR Co. plan - published ca. 1898 - zoomed in
^ Edinburgh Waverley on OS town plan (1887) showing 3-way release crossover points between platforms
^ Edinburgh Waverley on OS town plan (1894) showing 3-way release crossover points between platforms 2 & 3 and 4 & 5
^ Manchester Central on OS 1:500 town plan (1888) showing 3-way release crossover points between platforms 1 & 2, 3 & 4 and 5 & 6
^ Manchester Central station - Ordnance Survey 25" to the mile - published 1934
^ Manchester Central station looking towards the buffer stops (Disused Stations in the UK)
^ Manchester Central station from the buffer stops (Disused Stations in the UK)
^ 1864 - 1:500 town plan (Disused Stations)
^ Liverpool Exchange on OS 1:500 town plan (1890) showing 3-way release crossover points between platforms 4 & 5
^ Preston Hendry, R., Powell Hendry, R., (1982) An historical survey of selected LMS stations : layouts and illustrations. Vol. 1 Oxford Publishing
^ Leeds Central station from the buffer stops showing 3-way point for release crossovers
^ Leeds Central on OS 1:500 town plan (1910) showing 3-way release crossover points between platforms 2 & 3
^ "Moor Street Passenger Station". Warwickshirerailways.com. Retrieved 24 March 2013.
^ "Moor Street Station: Ex-GWR 2-6-2T 'Prairie' No 6152 is seen standing on the traverser as it is being moved from platform 2 to platform 1 on the right". Warwickshirerailways.com.
^ A locomotive at Moor Street being transferred to the run round loop for platform 3 (Warwickshirerailways.com)
^ "Station Name: Withernsea". Disused Stations. Subterranea Britannica. 19 April 2019. Retrieved 8 March 2022.
^ 1891 1:2,500 OS map showing the layout of Withernsea station (Disused Stations in the UK)

[1] Jackson, Alan A. (2006). The Railway Dictionary (4th ed.). Sutton Publishing Ltd. p. 298. ISBN 0-7509-4218-5.

[2] Ellis, Iain (2006). Ellis' British Railway Engineering Encyclopaedia. Lulu.com. p. 307. ISBN 978-1-8472-8643-7.

[3] "View map: Edinburghshire III.8 (Edinburgh) - Ordnance Survey 25 inch 2nd and later editions, Scotland, 1892-1949". maps.nls.uk.

[4] Edinburgh Waverley station - NBR Co. plan - published ca. 1898 - zoomed in

[5] Edinburgh Waverley on OS town plan (1887) showing 3-way release crossover points between platforms

[6] Edinburgh Waverley on OS town plan (1894) showing 3-way release crossover points between platforms 2 & 3 and 4 & 5

[7] Manchester Central on OS 1:500 town plan (1888) showing 3-way release crossover points between platforms 1 & 2, 3 & 4 and 5 & 6

[8] Manchester Central station - Ordnance Survey 25" to the mile - published 1934

[9] Manchester Central station looking towards the buffer stops (Disused Stations in the UK)

[10] Manchester Central station from the buffer stops (Disused Stations in the UK)

[11] 1864 - 1:500 town plan (Disused Stations)

[12] Liverpool Exchange on OS 1:500 town plan (1890) showing 3-way release crossover points between platforms 4 & 5

[13] Preston Hendry, R., Powell Hendry, R., (1982) An historical survey of selected LMS stations : layouts and illustrations. Vol. 1 Oxford Publishing

[14] Leeds Central station from the buffer stops showing 3-way point for release crossovers

[15] Leeds Central on OS 1:500 town plan (1910) showing 3-way release crossover points between platforms 2 & 3

[WARR-16] "Moor Street Passenger Station". Warwickshirerailways.com. Retrieved 24 March 2013.

[17] "Moor Street Station: Ex-GWR 2-6-2T 'Prairie' No 6152 is seen standing on the traverser as it is being moved from platform 2 to platform 1 on the right". Warwickshirerailways.com.

[18] A locomotive at Moor Street being transferred to the run round loop for platform 3 (Warwickshirerailways.com)

[19] "Station Name: Withernsea". Disused Stations. Subterranea Britannica. 19 April 2019. Retrieved 8 March 2022.

[20] 1891 1:2,500 OS map showing the layout of Withernsea station (Disused Stations in the UK)

[1]

[2]

[3]

[4]

[5]

[6]

[7]

[8]

[9]

[10]

[11]

[12]

[13]

[14]

[15]

[16]

[17]

[18]

[19]

[20]

@@ Line 1: / Line 1: @@
-[[Image:Toyooka station (Hyogo prefecture) Miyazu line engine running track.jpg|thumb|Platform track and run-round loop at [[Toyooka Station (Hyōgo)|Toyooka Station]], Hyōgo, Japan, the terminus of the line from [[Miyazu Line|Miyazu]]]] A '''headshunt''' (US: '''escape track''') is a short length of [[Rail tracks|track]], provided to release [[locomotive]]s at [[terminal station|terminal platforms]], or to allow [[Shunt (rail)|shunting]] to take place clear of main lines.
+{{Short description|A short length of track to release locomotives at terminal platforms}}
+{{multiple issues|
+{{more footnotes|date=September 2022}}
+{{original research|date=September 2022}}
+{{cleanup rewrite|date=September 2022}}
+}}
+[[File:Toyooka station (Hyogo prefecture) Miyazu line engine running track.jpg|thumb|Platform track and run-round loop at [[Toyooka Station (Hyōgo)|Toyooka Station]], Hyōgo, Japan, the terminus of the line from [[Miyazu Line|Miyazu]]]]A '''headshunt''' (or '''escape track''' in the [[United States]]) is a short length of [[Rail tracks|track]] provided to release [[locomotive]]s at [[Terminal station|terminal platforms]], or to allow [[Shunt (rail)|shunting]] to take place clear of main lines.
-== Terminal Headshunts ==
+==Terminal headshunt==
+[[File:Headshunt principle - end of line.svg|left|thumb|Sequence at a terminal headshunt: <br />
+. train arrives at the station<br />
+. locomotive is detached from the train and moves into the headshunt <br />
+. locomotive reverses and the points are switched<br />
+. locomotive travels along the passing loop to pass the cars<br />
+. locomotive reverses direction and the points are switched <br />
+. locomotive couples to the opposite end of the train <br />
+. locomotive reverses and the train departs
+]]
+A 'terminal headshunt' is a short length of track that allows a locomotive to uncouple from its train, move forward, and then run back past it on a parallel track. Such headshunts are typically installed at a [[terminal station]] to allow the locomotive of an arriving train to move to the opposite end of (in railway parlance, 'run around') its train so that it can then haul the same train out of the station in the other direction (assuming, of course, that it is a locomotive equipped to run in either direction; for locomotives that only operate in one direction, a [[Wye (rail)|wye]] or [[Railway turntable|turntable]] needs to be provided to physically turn the engine around, as well as a run-around track).
+==Reversing headshunt==
-A  '''terminal headshunt''' is a short length of track that allows a locomotive to uncouple from its train, move forward, and then run back past it on a parallel track. Such headshunts are typically installed at a [[terminal station]] to allow the locomotive of an arriving train to move to the opposite end of (in railway parlance, 'run around') its train, so that it can then haul the same train out of the station in the other direction.
+{{main article|Pocket track}}
+[[File:Melbourne University tram stop shunting area, looking south, 2013 (1).JPG|thumb|[[Melbourne University tram stop]] has three reversing headshunts in succession, between the two running lines.]]
+Found primarily on [[metro system]]s, [[rapid transit]] [[light rail]] networks, and [[tram]]ways, a 'reversing headshunt' allows certain trains or trams to change direction, even on lines with high traffic flow, whilst others continue through the station.
-== Shunting neck ==
+==Shunting neck==
+<!-- [[Shunting neck]] redirects here. -->
-The term headshunt may also refer to '''shunting neck''' or '''shunt spur''': a short length of [[Rail tracks|track]] laid parallel to the main line for the purpose of allowing a train to shunt back into a [[Rail siding|siding]] or [[rail yard]] without occupying the main running-line.
+The term headshunt may also refer to '''shunting neck''' or 'shunt spur': a short length of [[Rail tracks|track]] laid parallel to the main line to allow a train to shunt back into a [[Rail siding|siding]] or [[rail yard]] without occupying the main running-line.{{citation needed |date=September 2022}}
-==Run-round==
+==Run round==
+<!-- [[Run-round loop]] and [[Run-around loop]] redirect here. -->
-{{About|the track arrangement|heat recovery system|run around coil}}
+{{About|section=yes|the track arrangement|heat recovery system|run around coil}}
-[[Image:Headshunt.png|thumb|450px|right|Sketch of a headshunt and run-round loop]]
+[[File:Headshunt.png|thumb|450px|Diagram of a headshunt and run round loop]]
-A '''run-round loop''' (or '''run-around loop''')<!--both terms redirect here, hence bold--> is a track arrangement that enables a locomotive to attach to the opposite end of the train.  This process is known as "running round a train".<ref>{{Ellis' Railway Encyclopaedia|page=307}}</ref>  It is commonly performed to haul wagons onto a siding, or at a terminal station to prepare for a return journey.<ref>{{Railway Dictionary|page=298}}</ref>
+A '''run round loop''' (or '''run-around loop''') is a track arrangement that enables a locomotive to attach to the opposite end of the train. It is commonly used to haul wagons onto a siding, or at a terminal station to prepare for a return journey.<ref>{{Railway Dictionary|page=298}}</ref> This process is known as "running round a train".<ref>{{Ellis' Railway Encyclopaedia|page=307}}</ref>
-Although a common procedure when the majority of trains were locomotive-hauled, the manoeuvre is now comparatively rare on public service railways.{{Citation needed|date=August 2009}} Increased use of [[multiple unit]] and [[Push-pull train|push-pull]] passenger services avoids the requirement for dedicated track and the need for railway staff to detach and reattach the locomotive at track level.{{Citation needed|date=August 2009}} However, many [[heritage railway]]s (in the UK, at least) deliberately incorporate run-round loops at each end of the running line, partly because train services are usually locomotive-hauled, and partly because the run-round operation gives added interest to visitors.
+Although a common procedure for [[passenger train]]s when the majority of them were locomotive-hauled, the maneuver is now becoming rarer on public service railways.{{Citation needed|date=August 2009}} Increased use of [[multiple unit]] and [[Push-pull train|push-pull]] passenger services avoids the requirement for dedicated track and the need for railway staff to detach and reattach the locomotive at track level.{{Citation needed|date=August 2009}} However, on [[heritage railway]]s run-round loops are still usually more or less necessary at each end of the running line, partly because train services are usually locomotive-hauled, and partly because the run-round operation gives added interest to visitors. This practice is still very common on Intercity services in [[Victoria (Australia)|Victoria, Australia]].
-=== Examples ===
+Runaround tracks are used in [[freight rail]] service in order to back cars into spurs or to change directions to keep the locomotive at the front of the train for transport.  In this case the runaround track must be as long as the longest set of cars that would be pulled.  The locomotive leaves the cars on the runaround track or the main line, goes around, and hooks up to the other end of the train.  It can then reverse the cars into a spur.
+=== Examples ===
 Stations which used to have run-rounds include:
+* United Kingdom
-* [[St Ives railway station|St Ives]] (UK).
+** [[Edinburgh Waverley railway station]]; The terminal platforms of this station featured locomotive release roads between two main platforms, connected by a [[Railroad switch#Three-way switch|three-way point]] to the crossover from each platform line.<ref>{{Cite web|url=https://maps.nls.uk/view/82877409#zoom=6&lat=6818&lon=2812&layers=BT|title=View map: Edinburghshire III.8 (Edinburgh) - Ordnance Survey 25 inch 2nd and later editions, Scotland, 1892-1949|website=maps.nls.uk}}</ref><ref>[https://maps.nls.uk/transport/railways/rec/8233 Edinburgh Waverley station - NBR Co. plan - published ca. 1898] - [https://maps.nls.uk/view/216546773#zoom=4&lat=5471&lon=11924&layers=BT zoomed in]</ref><ref>[https://maps.nls.uk/view/74415668 Edinburgh Waverley on OS town plan (1887) showing 3-way release crossover points between platforms]</ref><ref>[https://maps.nls.uk/view/74415762 Edinburgh Waverley on OS town plan (1894) showing 3-way release crossover points between platforms 2 & 3 and 4 & 5]</ref>  The same arrangement of a three-way point on a central release road was also installed at the now closed stations:
-* [[Toronto railway station, New South Wales]] - now closed.
+*** [[Manchester Central railway station|Manchester Central]]<ref>[https://maps.nls.uk/view/231274368 Manchester Central on OS 1:500 town plan (1888) showing 3-way release crossover points between platforms 1 & 2, 3 & 4 and 5 & 6]</ref><ref>[https://maps.nls.uk/view/126522839#zoom=6&lat=7032&lon=11055&layers=BT Manchester Central station - Ordnance Survey 25" to the mile - published 1934]</ref><ref>[http://www.disused-stations.org.uk/m/manchester_central/index33.shtml Manchester Central station looking towards the buffer stops] ([http://www.disused-stations.org.uk/ Disused Stations in the UK])</ref><ref>[http://www.disused-stations.org.uk/m/manchester_central/index43.shtml Manchester Central station from the buffer stops] ([http://www.disused-stations.org.uk/ Disused Stations in the UK])</ref>
-* [[Cronulla railway station]] - had run round, but never had locomotives, now no run round.
+*** [[Liverpool Exchange railway station|Liverpool Exchange]]<ref>[http://www.disused-stations.org.uk/l/liverpool_exchange/index.shtml 1864 - 1:500 town plan] ([http://www.disused-stations.org.uk/ Disused Stations])</ref><ref>[https://maps.nls.uk/view/229948701 Liverpool Exchange on OS 1:500 town plan (1890) showing 3-way release crossover points between platforms 4 & 5]</ref><ref>Preston Hendry, R., Powell Hendry, R., (1982) ''An historical survey of selected LMS stations : layouts and illustrations. Vol. 1'' Oxford Publishing</ref>
-* [[Newcastle railway station, New South Wales]] - run-round on Platform 1&2, not on Platform 3&4.
+*** [[Leeds Central railway station|Leeds Central]]<ref>[[c:File:Leeds Central Station geograph-2334667-by-Ben-Brooksbank.jpg|Leeds Central station from the buffer stops showing 3-way point for release crossovers]]</ref><ref>[https://maps.nls.uk/view/229947285 Leeds Central on OS 1:500 town plan (1910) showing 3-way release crossover points between platforms 2 & 3]</ref>
+** [[St Ives railway station]]
+** [[Matlock Riverside railway station]], now closed
+** [[Birmingham Moor Street railway station|Birmingham Moor Street]].  This station is on a confined site, so to save space the platform lines were equipped with [[Transfer table|traversers]] to allow locomotives to run round via the adjacent platform line (platforms 1 & 2) or an adjacent loop (platform 3).<ref name=WARR>{{cite web|title=Moor Street Passenger Station|url=http://www.warwickshirerailways.com/gwr/moorstreet.htm|website=Warwickshirerailways.com|access-date=24 March 2013}}</ref><ref>{{cite web|url=http://www.warwickshirerailways.com/gwr/gwrms1223.htm|title=Moor Street Station: Ex-GWR 2-6-2T 'Prairie' No 6152 is seen standing on the traverser as it is being moved from platform 2 to platform 1 on the right|website=Warwickshirerailways.com}}</ref><ref>[https://www.warwickshirerailways.com/gwr/gwrms1735.htm A locomotive at Moor Street being transferred to the run round loop for platform  3] (Warwickshirerailways.com)</ref>
+** [[Withernsea railway station|Withernsea]], the terminal station on the now closed [[Hull and Holderness Railway]].  At this station, instead of a [[Railroad switch|crossover or points]] the run round loop was accessed from a [[Railway turntable|turntable]] at the end of the platform line and run round loop.<ref>{{cite web|url=http://www.disused-stations.org.uk/enwiki/w/withernsea/index.shtml|title=Station Name: Withernsea|date=19 April 2019|work=Disused Stations|publisher=Subterranea Britannica|accessdate=8 March 2022}}</ref><ref>[http://www.disused-stations.org.uk/enwiki/w/withernsea/index1.shtml 1891 1:2,500 OS map showing the layout of Withernsea station] ([http://www.disused-stations.org.uk/ Disused Stations in the UK])</ref>  There was a similar arrangement at [[Ventnor railway station|Ventnor]] and [[Bembridge railway station|Bembridge]] railway stations on the [[Isle of Wight Railway|Isle of Wight]].
+<gallery captions="Turntable and run round loop at Withernsea">
+File:Withernsea Railway Station.jpg|Turntable and run round loop at Withernsea
+File:Leeds Central Station geograph-2334667-by-Ben-Brooksbank.jpg|Leeds Central station showing the release crossovers
+</gallery>
+* Australia
+** [[Murwillumbah railway station]], now closed
+** [[Toronto railway station, New South Wales]], now closed
+** [[Cronulla railway station]], had run-round, but never had locomotives
+** [[Newcastle railway station, New South Wales]], now closed; run-round on Platform 1&2, not on Platform 3&4
 Stations which still have run-rounds include:
+* United Kingdom
-* [[Canberra]] and
+** [[Weymouth railway station]]
-* [[Murwullimbah]] - now closed
+** [[Fort William railway station]]
+** [[Morecambe railway station]]
+** [[Rowsley South railway station]]
+** [[Mallaig railway station]]
+* Germany
+** [[Hagen Hauptbahnhof]]
+* Australia (all in regular loco-hauled passenger use unless otherwise indicated)
+** [[Central railway station, Sydney]]
+** [[Albury railway station]]
+** [[Canberra railway station]] (run-around not in regular use)
+** [[Southern Cross railway station]] (Melbourne)
+** [[Shepparton railway station]]
+** [[Bairnsdale railway station]]
+** [[Geelong railway station]]
+** [[South Geelong railway station]]
+** [[Marshall railway station]]
+** [[Warrnambool railway station]]
+** [[Swan Hill railway station]]
+** [[Seymour railway station]]
+** [[Roma Street railway station]] (Brisbane) (not sure if run-around in use)
+** [[Toowoomba railway station]]
+** [[Charleville railway station]]
+** [[Rockhampton railway station]]
+** [[Longreach railway station]]
+** [[Townsville railway station]]
+** [[Mount Isa railway station]]
+** [[Cairns railway station]]
+** [[Kuranda railway station]]
+** [[Adelaide Parklands Terminal]]
+** [[Public Transport Centre]] (East Perth terminal)
+** [[Darwin railway station]]
-== References ==
+== No loop ==
+If a terminal station does not have a run-round loop trains are restricted to multiple units or [[Top and Tail]] trains.{{citation needed |date=September 2022}}
-<references/>
+==See also==
-{{Railway track layouts}}
+*[[Backshunt]]
+== References ==
-[[Category:Railway track layouts]]
+{{reflist}}
+{{Railway track layouts}}
+{{Rail tracks}}
+[[Category:Railway sidings]]
-{{train-stub}}
-[[zh:机走线]]
-[[de:Ausziehgleis]]
-[[ja:機回し線]]

v t e Railway track layouts
Railway track	Single track Passing loop Double track Quadruple track Crossover
Rail sidings	Balloon loop Headshunt Pocket track Refuge siding Rail yard Classification yard
Junctions	Flying junction Level junction Double junction Facing and trailing Grand union Grand circle / roundabout Wye Switch / turnout / points Swingnose crossing Level crossing
Stations	Railway platform Bay Island Side Split Terminal station Balloon loop Spanish solution Cross-platform interchange Interchange station Infill station
Hillclimbing	Horseshoe curve Zig Zag / Switchback Spiral
Track geometry	Track gauge Ruling gradient Minimum curve radius Cant Cant deficiency

v t e Rail infrastructure
Tracks (history)	Axe ties Ballast Baulk road Breather switch Cant Clip and scotch Date nail Fastening system Fishplate Ladder track Minimum radius Profile Tie/Sleeper Transition curve
Trackwork	Balloon loop Classification yard Headshunt Pocket track Junction Gauntlet track Guide bar Passing loop Track gauge dual gauge Rail track tramway track Rail yard Railway electrification overhead lines third rail ground-level power supply Railway turntable Transfer table (traverser) Roll way Siding refuge siding Switch Track geometry Water crane Water trough Wye
Signalling and safety	Anti-trespass panels Block post Buffer stop Catch points Defect detector Derailer Guard rail Interlocking Level crossing Loading gauge Platform screen doors Railway signal Signalling control Structure gauge Signal bridge Tell-tale Train stop Wayside horn
Structures	Coaling tower Motive power depot/Railway workshop Platform Roundhouse Shed for trains for goods Station building clock ghost list Water stop
Types	Industrial Military Private station list