Rex (chair): Difference between revisions

Content deleted Content added

Inline

Latest revision as of 00:17, 22 November 2024

The Rex Chair is a wooden chair designed by Slovene architect and designer Niko Kralj (1920–2013). It is part of the collection at the Museum of Modern Art (MoMA) in New York City.^[1] Kralj was awarded the Prešeren Prize for the Rex chair.^{[citation needed]} In 2012, it was given a permanent place in the Designmuseum Denmark, the largest museum of design in Scandinavia.^{[citation needed]} The Rex Chair was ranked as the second most significant Slovenian product of the 20th century by the "Finance" newspaper in 1999. [^{citation needed]} The Museum of Modern Art in Ljubljana devoted an exhibit to the Rex chair in 2004 for its 50th anniversary.^[2]

Development

Niko Kralj was manager of Stol development services when the chair was first introduced. It was the first chair in Slovenia made with the technology of molded, perforated plywood designed for mass production.

Basic designs

The back of this chair is slatted to allow for ventilation and to reduce weight. Bent plywood armrests support the elbows, and the back panel joints strengthen the chair's structure. Basic designs of the Rex Chair include:^[2]

Model 120 (1953): Plywood sidepieces were replaced with three-dimensionally turned, perforated plywood. The two extreme structural crosspieces on the front edge of the seat and the top of the back were removed and replaced by glued strips. The arm rests were made of bent wood.
Model 101 (1954): A Rex Chair 120 variation that does not have armrests. Removing the armrests compromised structural stability of the chair, so two cross bindings were added between the back legs for strength.
Model 5654 (1956): A collapsible variation model of 120 is the best-known chair in the REX family and is still being produced today as a low armchair intended to be used in covered areas. It has several varieties to suit its use, for example, as a club chair, a high-backed chair, or an auditorium chair.
Model 140: Has a back that is connected to the front legs, which meet the diagonal rear legs in the middle section. The height of the back panel is the same as the classic Rex Chair, and whole plywood is used for the upper half of the back panel.
Model 5652: A folding dining chair with a higher and shorter seat and legs that stand more vertically than in Model 101 (1954).
The restaurant chair has perforated seat and back panels, straight, standing legs, and a slightly inclined back. It is suitable for loading.
The Rex Program also included coffee tables, chaise lounges, and rocking chairs (Model 5655). Foreign manufacturers produced copies of the Rex Chair in plastic, which could also be used outdoors, but do not have the same aesthetics as the original.

Production

The exclusive holder of the manufacturing and distribution rights to the REX chair is Impakta Les.^[3] The REX Collection in production today consists of the Rex Folding Chair, Rex Folding Lounge Chair, Rex Folding Rocking Chair, Rex Folding Daybed and Rex Folding Table. As of 2023, they have produced over 2 million REX chairs.^[4]

Construction

First model (1952)

Made entirely of wood, this chair consisted of a solid beechwood frame that securely held pieces of bowed, rectangular-shaped plywood. The armrests, also made of solid wood with the front sections cut in a round shape, are joined statically to the two diagonal legs.

Second model

The ends of the curved sidepieces were fitted into the crosspieces at the edges of the seat and back panels, avoiding the use of visible wood screws on the front of the chair.

Third model

This is a prefabricated chair held together with nuts and bolts. The molded cross pieces create the seat and back panels. This was designed to address the problematic sharp bend between the seat and the back by shortening the individual rods. The seat and back are curved to the shape of the body with the rear legs extended into the armrest. The model required a lot of high-quality wood and produced a lot of waste.

Fourth model

The seat and back are the same as in the third model, with the armrest and the front and rear legs in one piece. It is made with veneers to minimized the amount of real wood used. The shortened armrests do not provide effective support.

Fifth model

The seat and the back are the same as in the third model. The front and back legs touch at the top and they spread apart diagonally downward. To support this A-shape, the plywood armrest, which is curved at a right angle (through high-frequency dielectric heating), is affixed to the upper section. The chair structure is strengthened further by the armrest being joined to the back panel.

Sixth model (1953)

The slats were shallowly set into the side element and not able to withstand the sudden weight. They were replaced by perforated, three-dimensionally, bent plywood shaped to the body's contours. The panels are inserted between two sidepieces. The edge pieces on the front of the seat panel and the top of the back panel are replaced by glued strips.

In 1954, Model No. 56 was accepted for mass production under the name Rex 120.^[2]

References

^ Teržan, Vesna (2012) Kralj, an architect, designer and inventor (Slovene: Niko Kralj, arhitekt, oblikovalec in izumitelj), Mladina, Ljubljana.
^ ^a ^b ^c Hrovatin, J. (2010) Design for all, all for design, Academy of Design, Ljubljana. ISBN 978-961-92619-2-7
^ "Pair of vintage Rex Folding chairs for Impakta Les in beech and metal 1960s". Design Market. Retrieved 2024-10-04.
^ "Rex". Rex Kralj. Retrieved 2024-10-04.

External links

REX Chair, official website
REX designed by Niko Kralj, interior magazine article, interiorzine.com

[1] Teržan, Vesna (2012) Kralj, an architect, designer and inventor (Slovene: Niko Kralj, arhitekt, oblikovalec in izumitelj), Mladina, Ljubljana.

[HorvatinJasnaPhD-2] Hrovatin, J. (2010) Design for all, all for design, Academy of Design, Ljubljana. ISBN 978-961-92619-2-7

[3] "Pair of vintage Rex Folding chairs for Impakta Les in beech and metal 1960s". Design Market. Retrieved 2024-10-04.

[4] "Rex". Rex Kralj. Retrieved 2024-10-04.

[1]

[2]

[3]

[4]

@@ Line 1: / Line 1: @@
+{{Short description|Slovenian design wood art chair made since 1952}}
 {{Other uses|Rex (disambiguation)}}
-[[File:Stol Rex.jpg|thumb|200px|right|Chair Rex.]]
+[[File:Stol Rex.jpg|thumb|200px|right|Rex Chair]]
-The '''"REX" Chair''' is a [[Scandinavian design]]-inspired [[wood]]en chair design that is included in the collection of the [[Museum of Modern Art, New York|Museum of Modern Art]] [[MOMA]] in [[New York]]<ref>Kolar, Damijana (2012) [http://www.mladina.si/107424/niko-kralj/ Niko Kralj], [[Mladina]], Ljubljana.</ref> and was designed by Slovene architect and designer [[Niko Kralj]] (1920-2013) in 1952.<ref>Teržan, Vesna (2012) [http://www.mladina.si/108144/niko-kralj-arhitekt-oblikovalec-in-izumitelj/Niko Kralj, an architect, designer and inventor] (Slovene: ''Niko Kralj, arhitekt, oblikovalec in izumitelj''), [[Mladina]], Ljubljana.</ref> In 2012, it was given a permanent place in [[Designmuseum]], [[Denmark]], the largest museum of design in Scandinavia. It became a cult object for design lovers around the globe with its calm contemporary elegance and a feeling of floating.<ref>Diskin, Steve (2012) [http://www.nikokralj.si/en/book_review.htm#Steve-Diskin Getting to Know Niko Kralj]</ref> It is the most internationally notable Slovenian design item and in 2004, at the 50 years anniversary of its development there was at the [[Museum of Modern Art Ljubljana|Museum of Modern Art]] in [[Ljubljana]] an exhibition devoted to the REX chair. REX chair was ranked at the second place as the Slovenian product of 20th century according to the ″[[Finance]]″ newspaper in 1999.<ref name="HorvatinJasnaPhD">Hrovatin, J. (2010) [http://www.nikokralj.si/en/book_colophon.htm Design for all, all for design], Academy of Design, Ljubljana. ISBN 978-961-92619-2-7</ref>
+The '''Rex Chair''' is a wooden [[chair]] designed by [[Slovenes|Slovene]] architect and designer Niko Kralj (1920–2013). It is part of the collection at the [[Museum of Modern Art, New York|Museum of Modern Art]] (MoMA) in [[New York City]].<ref>Teržan, Vesna (2012) [http://www.mladina.si/108144/niko-kralj-arhitekt-oblikovalec-in-izumitelj/Niko Kralj, an architect, designer and inventor] (Slovene: ''Niko Kralj, arhitekt, oblikovalec in izumitelj''), [[Mladina]], Ljubljana.</ref> Kralj was awarded the [[Prešeren Prize]] for the Rex chair.{{Citation needed|date=October 2024}} In 2012, it was given a permanent place in the [[Designmuseum Denmark]], the largest museum of design in [[Scandinavia]].{{Citation needed|date=October 2024}} The Rex Chair was ranked as the second most significant Slovenian product of the 20th century by the "Finance" newspaper in 1999. [<sup>''[[Wikipedia:Citations needed|citation needed]]'']</sup> The [[Museum of Modern Art Ljubljana|Museum of Modern Art]] in [[Ljubljana]] devoted an exhibit to the Rex chair in 2004 for its 50th anniversary.<ref name="HorvatinJasnaPhD">Hrovatin, J. (2010) [http://www.nikokralj.si/en/book_colophon.htm Design for all, all for design], Academy of Design, Ljubljana. {{ISBN|978-961-92619-2-7}}</ref>
 ==Development==
-At the time Kralj was manager of [[Stol(company)|Stol]] development services. He ranked among such international industrial design legends as Charles and [[Ray Eames]] or [[Alvar Aalto]] and has conquered the world with his innovative design. Kralj received the [[Prešeren Prize]], as well. The REX chair was elevated to the level of a cult item. It was the first chair in [[Slovenia]] made in technology of molded, perforated [[plywood]] designed for mass production.
+Niko Kralj was manager of Stol development services when the chair was first introduced. It was the first chair in [[Slovenia]] made with the technology of molded, perforated [[plywood]] designed for mass production.
 ===Basic designs===
-The back of the chair is perforated to allow for ventilation and to reduce the weight. Bent plywood armrests support the elbows and joint to the back panel strengthens the chair structure. Basic designs of the REX Chair include:<ref name="HorvatinJasnaPhD"/>
+The back of this chair is slatted to allow for ventilation and to reduce weight. Bent [[plywood]] armrests support the elbows, and the back panel joints strengthen the chair's structure. Basic designs of the Rex Chair include:<ref name="HorvatinJasnaPhD"/>
-* Model 120 (1953) the plywood sidepieces were replaced with perforated three dimensionally turned plywood. The two extreme structural crosspieces on the front edge of the seat and the top of the back were removed and replaced by glued strips. The armrests were made of bent wood.
+* Model 120 (1953): [[Plywood]] sidepieces were replaced with three-dimensionally turned, perforated [[plywood]]. The two extreme structural crosspieces on the front edge of the seat and the top of the back were removed and replaced by glued strips. The arm rests were made of bent wood.
-* Model 101 (1954) is a variation of REX Chair 120, without armrests. Removing the armrests had a negative effect of structural stability, so two cross bindings were added between the rear legs for strength.
+* Model 101 (1954): A Rex Chair 120 variation that does not have armrests. Removing the armrests compromised structural stability of the chair, so two cross bindings were added between the back legs for strength.
-* Model 5654 (1956), the best known chair in the Rex family, is still being produced today, as a low armchair intended to be used in covered areas. It has been produced in various styles depending on its assigned use, as a club chair, a high-backed chair or an auditorium chair. Rex 5654, a collapsible variation model of 120, was patented in 1958 as a unique kind of folding armchair. All elements in the chair are mutually connected.
+* Model 5654 (1956): A collapsible variation model of 120 is the best-known chair in the REX family and is still being produced today as a low armchair intended to be used in covered areas. It has several varieties to suit its use, for example, as a club chair, a high-backed chair, or an auditorium chair.
-* Model 140 has a back that is connected to the front legs, which meet the diagonal rear legs in the middle section. The height of the back panel is the same as in the classic REX Chair, only here whole plywood is used for the upper half of the back panel.
+* Model 140: Has a back that is connected to the front legs, which meet the diagonal rear legs in the middle section. The height of the back panel is the same as the classic Rex Chair, and whole plywood is used for the upper half of the back panel.
-* Model 5652 is a folding dining chair with a higher and shorter seat and with legs that stand more vertically than in Model 1954.
+* Model 5652: A folding dining chair with a higher and shorter seat and legs that stand more vertically than in Model 101 (1954).
-* The restaurant chair has perforated seat and back panels, straight/standing legs and a slightly inclined back. It is suitable for loading.
+* The restaurant chair has perforated seat and back panels, straight, standing legs, and a slightly inclined back. It is suitable for loading.
-* The Rex Program also included coffee tables, chaises lounges, and rocking chairs (Model 5655). Foreign manufacturers produced copies of the REX Chair in plastic. These chairs could be used outdoors, as well, but they never attained the high aesthetic quality of the original.
+* The Rex Program also included coffee tables, chaise lounges, and rocking chairs (Model 5655). Foreign manufacturers produced copies of the Rex Chair in plastic, which could also be used outdoors, but do not have the same aesthetics as the original.
 ==Production==
-Exclusive holder for manufacturing and distribution rights of REX chair is Impakta Les. REX Collection in production today consists of Rex Folding Chair, Rex Folding Lounge Chair, Rex Folding Rocking Chair, Rex Folding Daybed and Rex Folding Table.
+The exclusive holder of the manufacturing and distribution rights to the REX chair is Impakta Les.<ref>{{Cite web |title=Pair of vintage Rex Folding chairs for Impakta Les in beech and metal 1960s |url=https://www.design-market.us/94456-pair-of-vintage-rex-folding-chairs-for-impakta-les-in-beech-and-metal-1960s.html?redirected=true |access-date=2024-10-04 |website=Design Market |language=en}}</ref> The REX Collection in production today consists of the Rex Folding Chair, Rex Folding Lounge Chair, Rex Folding Rocking Chair, Rex Folding Daybed and Rex Folding Table.
+As of 2023, they have produced over 2 million REX chairs.<ref>{{Cite web |title=Rex |url=https://rex-kralj.com/collection/rex/?_gl=1*1qco1no*_up*MQ..*_ga*MTA4Mjc5NjY5My4xNzI4MDI1Njgx*_ga_ZTMGNBHTEH*MTcyODAyNTY4MC4xLjAuMTcyODAyNTY4MC4wLjAuMA.. |access-date=2024-10-04 |website=Rex Kralj}}</ref>
-Until today, they have produced over 2 [[million]] chairs.
-==History==
+==Construction==
-* First model (1952)
+=== First model (1952) ===
-The Chair is made entirely of wood. It consists of a solid beechwood frame for secured pieces of bowed plywood with a rectangular shape. The armrests, made of solid wood with the front sections cut in a round shape, are joined statically to the two diagonal legs.
+Made entirely of wood, this chair consisted of a solid [[Beech wood|beechwood]] frame that securely held pieces of bowed, rectangular-shaped plywood. The armrests, also made of solid wood with the front sections cut in a round shape, are joined statically to the two diagonal legs.
-* Second model
-The end of the curved sidepieces are set in the crosspieces at the edges of the seat and the back panels; in this way the use of visible wood screws is avoided at the front of the chair. The crosspiece on the seat contributes to the chair’s greater comfort.
-* Third model
+=== Second model ===
+The ends of the curved sidepieces were fitted into the crosspieces at the edges of the seat and back panels, avoiding the use of visible wood screws on the front of the chair.
-The seat and the back panels are created by the cross pieces designed in a mold. In this way, the problematic sharp bend between the seat and the back is avoided and the length of individual rods is shortened. The seat and back are curved to the shape of the body. The rear legs extend into the armrest. The formation of this element requires high-quality wood with a good deal of waste involved. This is a prefabricated chair held together with bolts and nuts.
-* Fourth model
+=== Third model ===
-The seat and back are the same as in the third model. The armrest and the front and rear legs are all in one piece. This element is made of veneers designed in a mold and requires solid wood reinforcements. “The use of wood is reduced to the minimum; the armchair is prefabricated and stable even without bindings on the legs.” The shortened armrests, however, is problematic, since it does not provide the best support, especially for the elbow.
+This is a prefabricated chair held together with nuts and bolts. The molded cross pieces create the seat and back panels. This was designed to address the problematic sharp bend between the seat and the back by shortening the individual rods. The seat and back are curved to the shape of the body with the rear legs extended into the armrest. The model required a lot of high-quality wood and produced a lot of waste.
-* Fifth model
-Te seat and the back are the same as in the third model. The front and rear legs touch at the top and the spread apart diagonally downwards. To support this A-shape, the plywood armrest, which is curved at a right angle (through high-frequency dielectric heating), is affixed to the upper section. The chair structure is strengthened further by the armrest being joined to the back panel.
-* Sixth model (1953)
+=== Fourth model ===
+The seat and back are the same as in the third model, with the armrest and the front and rear legs in one piece. It is made with veneers to minimized the amount of real wood used. The shortened armrests do not provide effective support.
-The slats that were set shallowly into the side element were not able to withstand abrupt burdens and so are replaced by perforated three-dimensionally  bent plywood, shaped to the contours of the body. The panels is inserted between two sidepieces. The edge pieces on the front of the seat panel and the top of the back panel are replaces by glued strips.
-In 1954, Model No. 56 was accepted for mass production under the name Rex 120.<ref name="HorvatinJasnaPhD"/>
+=== Fifth model ===
+The seat and the back are the same as in the third model. The front and back legs touch at the top and they spread apart diagonally downward. To support this A-shape, the plywood armrest, which is curved at a right angle (through high-frequency dielectric heating), is affixed to the upper section. The chair structure is strengthened further by the armrest being joined to the back panel.
+=== Sixth model (1953) ===
+The slats were shallowly set into the side element and not able to withstand the sudden weight. They were replaced by perforated, three-dimensionally, bent plywood shaped to the body's contours. The panels are inserted between two sidepieces. The edge pieces on the front of the seat panel and the top of the back panel are replaced by glued strips.
+In 1954, Model No. 56 was accepted for mass production under the name Rex 120.<ref name="HorvatinJasnaPhD" />
 ==References==
@@ Line 39: / Line 47: @@
 ==External links==
-*[http://www.rex-chair.com REX Chair], official website
+*[https://rex-kralj.com/ REX Chair], official website
 *[http://interiorzine.com/2010/12/28/rex-program-designed-by-niko-kralj-under-brand-name-rex-kralj/ REX designed by Niko Kralj], interior magazine article, interiorzine.com
 [[Category:Chairs]]
+[[Category:Individual models of furniture]]
+[[Category:Portable furniture]]