Taxiway

Taxiway Light

A taxiway is a path on an airport connecting runways with ramps, hangars, terminals and other facilities. They mostly have hard surface such as asphalt or concrete, although smaller airports sometimes use gravel or grass.

Busy airports typically construct high-speed or rapid-exit taxiways in order to allow aircraft to leave the runway at higher speeds. This allows the aircraft to vacate the runway quicker, permitting another to land in a shorter space of time.
For exhaustive information on taxiways please refer to Aeronautical Information Manual published yearly by Federal Aviation Administration.

Taxiway markings

• Normal Centerline. A single continuous yellow line, 6 inches (15 cm) to 12 inches (30 cm) in width.
• Enhanced Centerline. Used at the larger commercial service airports. The enhanced taxiway centerline marking consists of a parallel line of yellow dashes on either side of the normal taxiway centerline. Maximum of 150 feet prior to a runway holding position marking.
• Taxiway Edge Markings. Used to define the edge of the taxiway when the taxiway edge does not correspond with the edge of the pavement. Continuous Markings consist of a continuous double yellow line, with each line being at least 6 inches (15 cm) in width spaced 6 inches (15 cm) apart and are used to define the taxiway edge from the shoulder or some other abutting paved surface not intended for use by aircraft. Dashed Markings. are used to define the edge of a taxiway on a paved surface where the adjoining pavement to the taxiway edge is intended for use by aircraft, e.g., an apron. Dashed taxiway edge markings consist of a broken double yellow line, with each line being at least 6 inches (15 cm) in width, spaced 6 inches (15 cm) apart (edge to edge). These lines are 15 feet (4.5 m) in length with 25 foot (7.5 m) gaps.
• Taxi Shoulder Markings. Taxiways, holding bays, and aprons are sometimes provided with paved shoulders to prevent blast and water erosion. Shoulders are not intended for use by aircraft, and may be unable to carry the aircraft load. Taxiway shoulder markings are yellow lines perpendicular to taxiway edge, from taxiway edge to pavement edge, about 10 feet apart.
• Surface Painted Taxiway Direction Signs. Yellow background with a black inscription, and are provided when it is not possible to provide taxiway direction signs at intersections, or when necessary to supplement such signs. These markings are located on either side of the taxiway centerline.
• Surface Painted Location Signs. Black background with a yellow inscription. When necessary, these markings are used to supplement location signs located along side the taxiway and assist the pilot in confirming the designation of the taxiway on which the aircraft is located. These markings are located on the right side of the centerline.
• Geographic Position Markings. These markings are located at points along low visibility taxi routes (when RVR is below 1200 feet(360m)). They are positioned to the left of the taxiway centerline in the direction of taxiing. Black inscription centered on pink circle with black inner and white outer ring.

• Runway Holding Position Markings. For runways, these markings indicate where an aircraft is supposed to stop when approaching a runway. They consist of four yellow lines, two solid and two dashed, spaced six or twelve inches apart, and extending across the width of the taxiway or runway. The solid lines are always on the side where the aircraft is to hold. There are three locations where runway holding position markings are encountered: Runway holding position markings on taxiways, runway holding position markings on runways, taxiways located in runway approach areas.
• Holding Position Markings for Instrument Landing System (ILS). These consist of two yellow solid lines spaced two feet apart connected by pairs of solid lines spaced ten feet apart extending across the width of the taxiway.
• Holding Position Markings for Taxiway/Taxiway Intersections. These consist of a single dashed line extending across the width of the taxiway.
• Surface Painted Holding Position Signs. Red background signs with a white inscription and supplement the signs located at the holding position.

The taxiways are given alphanumeric identification. These taxiway IDs are shown on black and yellow signboards along the taxiways.

Taxiway lights

For night operations, taxiways at great number of airports are equipped with lights, athough, some small airport are not equipped with them

• Taxiway Edge Lights. Used to outline the edges of taxiways during periods of darkness or restricted visibility conditions. These fixtures are elevated and emit blue light.
• Taxiway Centerline Lights. They are steady burning and emit green light located along the taxiway centerline
• Clearance Bar Lights. Three in-pavement steady-burning yellow lights installed at holding positions on taxiways
• Runway Guard Lights. Either a pair of elevated flashing yellow lights installed on either side of the taxiway, or a row of in-pavement yellow lights installed across the entire taxiway, at the runway holding position marking at taxiway/runway intersections.
• Stop Bar Lights. A row of red, unidirectional, steady-burning in-pavement lights installed across the entire taxiway at the runway holding position, and elevated steady-burning red lights on each side used in low visibility conditions (below 1,200 ft RVR). A controlled stop bar is operated in conjunction with the taxiway centerline lead-on lights which extend from the stop bar toward the runway. Following the ATC clearance to proceed, the stop bar is turned off and the lead-on lights are turned on.

Taxiway lights are spaced 75 feet apart from each other. In some airports, the lights are closer at the intersections.

References

[1] Areonautical Information Manual - U.S. Federal Aviation Administration - published yearly.
[2] Airport Facility Directory - U.S. Federal Aviation Administration - published every eight weeks.

See also

• Aviation
• Runway