Datapoint 2200

Datapoint 2200

Datapoint 2200 computer
Manufacturer	Computer Terminal Corporation
Type	Intelligent terminal, personal computer
Release date	May 1970 (1970-05)
Discontinued	1979 (1979)
Operating system	Datapoint O/S
CPU	serial, discrete logic implementation of the Intel 8008 instruction set
Memory	2 KB standard; expandable to 16 KB
Display	Text only, 80×12 characters

The Datapoint 2200 was a mass-produced programmable terminal usable as a computer, designed by Computer Terminal Corporation (CTC) founders Phil Ray and Gus Roche and announced by CTC in June 1970 (with units shipping in 1971). It was initially presented by CTC as a versatile and cost-efficient terminal for connecting to a wide variety of mainframes by loading various terminal emulations from tape rather than being hardwired as most contemporary terminals, including their earlier Datapoint 3300.

Dave Gust, a CTC salesman, realized that the 2200 could meet Pillsbury Foods's need for a small computer in the field, after which the 2200 was marketed as a stand-alone computer. Its industrial designer John "Jack" Frassanito has later claimed that Ray and Roche always intended the Datapoint 2200 to be a full-blown personal computer, but that they chose to keep quiet about this so as not to concern investors and others.

The terminal's multi-chip CPU (processor)'s instruction set became the basis of the Intel 8008 instruction set, which inspired the Intel 8080 instruction set and the x86 instruction set used in the processors for the original IBM PC and its descendants.

Technical description

Datapoint 2200 version I registers

12

11

10

09

08

07

06

05

04

03

02

01

00

(bit position)

Main registers

A

Accumulator

B

B register

C

C register

D

D register

E

E register

H

H register (indirect)

L

L register (indirect)

Program counter

P

Program Counter

Push-down address call stack

AS

Call level 1

AS

Call level 2

AS

Call level 3

AS

Call level 4

AS

Call level 5

AS

Call level 6

AS

Call level 7

Flags

C

P

Z

S

Flags

The Datapoint 2200 had a built-in full-travel keyboard, a built-in 12-line, 80-column green screen monitor, and two 47 character-per-inch cassette tape drives each with 130 KB capacity. Its size, 9+5⁄8 in × 18+1⁄2 in × 19+5⁄8 in (24 cm × 47 cm × 50 cm), and shape—a box with protruding keyboard—approximated that of an IBM Selectric typewriter. Initially, a Diablo 2.5 MB 2315-type removable cartridge hard disk drive was available, along with modems, several types of serial interface, parallel interface, printers and a punched card reader. Later, an 8-inch floppy disk drive was also made available, along with other, larger hard disk drives. An industry-compatible 7/9-track (user selectable) magnetic tape drive was available by 1975. In late 1977, Datapoint introduced ARCNET local area networking. The original Type 1 2200 shipped with 2 kilobytes (KiB) of serial shift register main memory, expandable to 8 KiB. The Type 2 2200 used denser 1 kbit RAM chips, giving it a default 4 KiB of memory, expandable to 16 KiB. Its starting price was around US$5,000 (equivalent to $38,000 in 2023), and a full 16 KiB Type 2 2200 had a list price of just over $14,000.

The 8-bit processor architecture that CTC designed for the Datapoint 2200 was implemented in four distinct ways, all with nearly identical instruction sets, but very different internal microarchitectures: CTC's original design that communicated data serially, CTC's parallel design, the Texas Instruments TMC 1795, and the Intel 8008.

Datapoint 2200 Version II (CTC's parallel design) was much faster than the TMC 1795, which was slightly faster than the original serial design of the Datapoint 2200, which in turn was considerably faster than the 8008.

The 2200 models were succeeded by the 5500, 1100, 6600, 3800/1800, 8800, etc.

The fact that most laptops and cloud computers today store numbers in little-endian format is carried forward from the original Datapoint 2200. Because the original Datapoint 2200 had a serial processor, it needed to start with the lowest bit of the lowest byte in order to handle carries. Microprocessors descended from the Datapoint 2200 (the 8008, Z80, and the x86 chips used in most laptops and cloud computers today) kept the little-endian format used by that original Datapoint 2200.

The seed of the x86 architecture

The original design called for a single-chip 8-bit microprocessor for the CPU, rather than a processor built from discrete TTL modules as was conventional at the time. In 1969, CTC contracted two companies, Intel and Texas Instruments (TI), to make the chip. TI was unable to make a reliable part and dropped out. Intel was unable to make CTC's deadline. Intel and CTC renegotiated their contract, ending up with CTC keeping its money and Intel keeping the eventually completed processor.

CTC released the Datapoint 2200 using about 100 TTL components (SSI/MSI chips) instead of a microprocessor, while Intel's single-chip design, eventually designated the Intel 8008, was finally released in April 1972.

Even though the Datapoint 2200 processor design employed a bit-serial microarchitecture, operating one bit at a time, it performed faster than the Intel 8008 microprocessor which employed an 8-bit parallel microarchitecture.

Possibly because of their speed advantages compared to MOS circuits, Datapoint continued to build processors out of TTL chips until the early 1980s.

Nonetheless, the 8008 was to have a seminal importance. It was the basis of Intel's line of 8-bit CPUs, which was followed by their assembly language compatible 16-bit CPUs — the first members of the x86 family, as the instruction set was later to be known. Already successful and widely used, the x86 architecture's further rise after the success in 1981 of the original IBM Personal Computer with an Intel 8088 CPU means that most desktop, laptop, and server computers in use today have a CPU instruction set directly based on the work of CTC's engineers. The instruction set of the highly successful Zilog Z80 microprocessor can also be traced back to the Datapoint 2200 as the Z80 was backwards-compatible with the Intel 8080. More immediately, the Intel 8008 was adopted by very early microcomputers including the SCELBI, Mark-8, MCM/70 and Micral N.

Instruction set

Instructions are one to three bytes long, consisting of an initial opcode byte, followed by up to two bytes of operands which can be an immediate operand or a program address. Instructions operate on 8-bits only; there are no 16-bit operations. There is only one mechanism to address data memory: indirect addressing pointed to by a concatenation of the H and L registers, referenced as M. The 2200 does, however, support 13-bit program addresses. It has automatic CALL and RETURN instructions for multi-level subroutine calls and returns which can be conditionally executed, like jumps. Direct copying may be made between any two registers or a register and memory. Eight math/logic functions are supported between the accumulator (A) and any register, memory, or an immediate value. Results are always deposited in A. Most instructions are executed in 16μs, 24μs, or a leisurely 520μs when accessing M. The 520μs represents the delay of the 2200's shift register memory to fully recirculate back to the next instruction. Branch type instructions take a variable amount of time (24μs to 520μs) depending on the distance of the branch.

Datapoint 2200 version I instruction set

Opcode								Operands		Mnemonic	Time μs	Description
7	6	5	4	3	2	1	0	b2	b3
0	0	0	0	0	0	0	X	—	—	HALT	—	Halt
0	0	0	0	0	0	1	0	—	—	SLC	16	A1-7 ← A0-6; A0 ← Cy ← A7
0	0	CC			0	1	1	—	—	Rcc (RETURN conditional)	16/†	If cc true, P ← (stack)
0	0	ALU			1	0	0	data	—	AD AC SU SB ND XR OR CP data	16	A ← A [ALU operation] data
0	0	DDD			1	1	0	data	—	Lr data (Load r with immediate data)	16	DDD ← data (except M)
0	0	0	0	0	1	1	1	—	—	RETURN	†	P ← (stack)
0	0	0	0	1	0	1	0	—	—	SRC	16	A0-6 ← A1-7; A7 ← Cy ← A0
0	1	CC			0	0	0	addlo	addhi	Jcc add (JMP conditional)	24/†	If cc true, P ← add
0	1	0	0	0	0	0	1	—	—	INPUT	16	A ← input
0	1	command					1	—	—	EX command (external command)	16	command ← A (coded 8-31 only)
0	1	CC			0	1	0	addlo	addhi	Ccc add (CALL conditional)	24/†	If cc true, (stack) ← P, P ← add
0	1	0	0	0	1	0	0	addlo	addhi	JMP add	†	P ← add
0	1	0	0	0	1	1	0	addlo	addhi	CALL add	†	(stack) ← P, P ← add
1	0	ALU			SSS			—	—	ADr ACr SUr SBr NDr XRr ORr CPr	16/520	A ← A [ALU operation] SSS
1	1	0	0	0	0	0	0	—	—	NOP	16	No operation (Actually LAA)
1	1	DDD			SSS			—	—	Lds (Load d with s)	16/520	DDD ← SSS
1	1	1	1	1	1	1	1	—	—	HALT	—	Halt
7	6	5	4	3	2	1	0	b2	b3	Mnemonic	Time μs	Description
SSS DDD					2	1	0	CC		ALU
A					0	0	0	FC, C false		ADr AD (A ← A + arg)	† Variable. Can be from 24μs to 520μs.
B					0	0	1	FZ, Z false		ACr AC (A ← A + arg + Cy)
C					0	1	0	FS, S false		SUr SU (A ← A - arg)
D					0	1	1	FP, P odd		SBr SB (A ← A - arg - Cy)
E					1	0	0	TC, C true		NDr ND (A ← A ∧ arg)
H					1	0	1	TZ, Z true		XRr XR (A ← A ⊻ arg)
L					1	1	0	TS, S true		ORr OR (A ← A ∨ arg)
M					1	1	1	TP, P even		CPr CP (A - arg)
SSS DDD					2	1	0	CC		ALU

Code example

The following Datapoint 2200 assembly source code is for a subroutine named MEMCPY that copies a block of data bytes from one location to another. Because the byte counter is only 8 bits, there is enough room to load all the subroutine parameters into the 2200's register file. If a 16 bit count is needed, a more complicated copy routine with parameters held in memory would be required.

002000 317 002001 206 020 004 002004 371 002005 206 020 004 002010 302 002011 024 001 002013 320 002014 110 000 004 002017 007 002020 306 002021 364 002022 004 001 002024 340 002025 305 002026 353 002027 014 000 002031 330 002032 007 002032

; MEMCPY -- ; Copy a block of memory from one location to another ; ; Entry parameters in registers ; HL: 13-bit address of source data block ; DE: 13-bit address of target data block ; C: 8-bit count of bytes to copy. (1 to 256 bytes) ORG 2000Q ;Code at 002000 octal MEMCPY LBM ;Read source byte into B CALL XCHGI ;Exchange HL<->DE and increment DE LMB ;Save B to target byte CALL XCHGI ;Exchange HL<->DE and increment DE LAC ;Decrement byte counter in C SU 1 LCA JFZ MEMCPY ;Continue for all bytes RETURN ;Exchange DE and HL register pairs then increment DE as 16 bits XCHGI LAL ;Exchange L and E LLE AD 1 ;and inc E, low byte of DE LEA LAH ;Exchange H and D LHD AC 0 ;proagate Cy into D LDA RETURN END

Credits

The original instruction set architecture was developed by Victor Poor and Harry Pyle. The TTL design they ended up using was made by Gary Asbell. Industrial design (how the box's exterior looked, including the company's logo) was done by Jack Frassanito.

Specifications

Main unit

• Processor: 8-bit CPU instruction set architecture with a bit-serial microarchitecture made from standard TTL components. The Intel 8008 was a nearly 100% compatible 8-bit microarchitecture design and LSI microprocessor implementation.
• Memory: 2K byte shift register memory, expandable to 8K (Version II: 4K RAM, expandable to 16K)
• Display: Text only, 80×12 characters
• Storage: 2 tape drives, optional 8-inch Shugart floppy drive

Peripherals

Users of the 2200 and succeeding terminals eventually had several optional units to choose from. Among these were:

• Modems
• Hard disks
• Printers
• ARCnet LAN

See also

• Kenbak-1

External links

• Information about the Datapoint 2200 at OLD-COMPUTERS.COM – Including a picture of the terminal
• Datapoint documentation on bitsavers.org
• Page with links to a doctoral thesis about early microprocessor history, with many details about Datapoint's role
• The man who invented the PC
• datapoint.org: Unofficial Datapoint Organization WEB site