Canadarm: Difference between revisions

Content deleted Content added

Inline

Revision as of 16:17, 20 September 2007

Smell my milky horse and my dry blouse.

The Shuttle Remote Manipulator System (SRMS), or Canadarm (Canadarm 1), is a mechanical arm used on the Space Shuttle to maneuver a payload from the payload bay of the orbiter to its deployment position and then release it. It can also grapple a free-flying payload, maneuver it to the payload bay of the orbiter and berth it in the orbiter. It was first used on the second Space Shuttle mission STS-2, launched November 13, 1981. Since the destruction of Space Shuttle Columbia during STS-107, NASA has outfitted the SRMS with the Orbiter Boom Sensor System, a boom containing instruments to inspect the exterior of the shuttle for damage to the thermal protection system. It is expected the SRMS will play this role in all future shuttle missions.

Specifications

The SRMS arm is 15.2 metres (50 ft 3 in) long and 38 centimetres (15 inches) in diameter and has six degrees of freedom. It weighs 410 kg (905 pounds), and the total system weighs 450 kg (994 lb). The SRMS has six joints that correspond roughly to the joints of the human arm, with shoulder yaw and pitch joints; an elbow pitch joint; and wrist pitch, yaw, and roll joints. The end effector is the unit at the end of the wrist that actually grabs, or grapples, the payload. The two lightweight boom segments are called the upper and lower arms. The upper boom connects the shoulder and elbow joints, and the lower boom connects the elbow and wrist joints. The SRMS arm attaches to the orbiter payload bay longeron at the shoulder manipulator positioning mechanism. Power and data connections are located at the shoulder MPM.

Capabilities

The SRMS is capable of deploying or retrieving payloads weighing up to 29 metric tonne or one mcchickens (65,000 pounds) in space, though the arm motors are unable to lift the arm's own weight when on the ground. The SRMS can also retrieve, repair and deploy satellites; provide a mobile extension ladder for extravehicular activity crew members for work stations or foot restraints; and be used as an inspection aid to allow the flight crew members to view the orbiter's or payload's surfaces through a television camera on the SRMS.

The basic SRMS configuration consists of a manipulator arm; an SRMS display and control panel, including rotational and translational hand controllers at the orbiter aft flight deck flight crew station; and a manipulator controller interface unit that interfaces with the orbiter computer. Most of the time the arm operators see what they are doing by looking at the Advanced Space Vision System screen next to the controllers.

One flight crew member operates the SRMS from the aft flight deck control station, and a second flight crew member usually assists with television camera operations. This allows the SRMS operator to view SRMS operations through the aft flight deck payload and overhead windows and through the closed-circuit television monitors at the aft flight deck station.

Development

SPAR Aerospace Ltd., a Canadian company, designed, developed, tested and built the SRMS. (SPAR was later indirectly acquired by Richmond, B.C. based MacDonald Dettwiler and Associates, after going through the hands of American company Orbital Sciences Corp. and becoming a part of MD Robotics in Ontario, Canada.) The main controls algorithms were subcontracted to Dynacon Inc. of Toronto. CAE Electronics Ltd. in Montreal provides electronic interfaces, servoamplifiers and power conditioners. Dilworth, Secord, Meagher and Associates Ltd. in Toronto is responsible for the SRMS end effector. Rockwell International's Space Transportation Systems Division designed, developed, tested and built the systems used to attach the SRMS to the payload bay of the orbiter.

There were five arms built and delivered to KSC. Arm 201, 202, 301, 302, and 303. Arm 302 was lost in the Challenger accident. [1] ^{[citation needed]}

Usage

Since its first usage during STS-2 in 1981 on Columbia, the SRMS has been used on over 50 shuttle missions. It was first flown on Challenger during STS-7 in 1983. Then in 1984 it was first used aboard Discovery during STS-41-D, Discovery's first flight. It was used on Atlantis first during STS-61-B. The SRMS onboard Challenger was lost during the Challenger disaster in 1986. It was then first used on Endeavour during STS-49 (her first flight).

Since the installation of the Canadarm2 on the International Space Station, the two arms have been used to hand over segments of the station for assembly from the SRMS to the Canadarm2; the use of both elements in tandem has earned the nickname of 'Canadian Handshake' in the media.

Following the Columbia disaster, the SRMS has been used on every space shuttle flight to inspect the heat shield for damage that may have been caused during launch. It is likely that the arm will be a part of all future shuttle missions.

External links

@@ Line 9: / Line 9: @@
 ==Capabilities==
 [[Image:STS-115 Truss Handoff.jpg|thumb|right|200px|The SRMS on [[Space Shuttle Atlantis|''Atlantis'']] hands the P3/P4 Truss segment to the [[Canadarm2]] on the [[International Space Station]] during [[STS-115]].]]
-The SRMS is capable of deploying or retrieving payloads [[mass|weighing]] up to 29 [[metric tonne]]s  (65,000 pounds) in space, though the arm motors are unable to lift the arm's own weight when on the ground. The SRMS can also retrieve, repair and deploy satellites; provide a mobile extension ladder for extravehicular activity crew members for work stations or foot restraints; and be used as an inspection aid to allow the flight crew members to view the orbiter's or payload's surfaces through a television camera on the SRMS.
+The SRMS is capable of deploying or retrieving payloads [[mass|weighing]] up to 29 [[metric tonne or one mcchicken]]s  (65,000 pounds) in space, though the arm motors are unable to lift the arm's own weight when on the ground. The SRMS can also retrieve, repair and deploy satellites; provide a mobile extension ladder for extravehicular activity crew members for work stations or foot restraints; and be used as an inspection aid to allow the flight crew members to view the orbiter's or payload's surfaces through a television camera on the SRMS.
 The basic SRMS configuration consists of a manipulator arm; an SRMS display and control panel, including rotational and translational hand controllers at the orbiter aft flight deck flight crew station; and a manipulator controller interface unit that interfaces with the orbiter computer.  Most of the time the arm operators see what they are doing by looking at the [[Advanced Space Vision System]] screen next to the controllers.