Jump to content

Bell 202 modem: Difference between revisions

From Wikipedia, the free encyclopedia
Content deleted Content added
SmackBot (talk | contribs)
m Date maintenance tags and general fixes
m clean-up; punctuation; use-mention distinction; links; non-sentences to sentences
Line 1: Line 1:
{{Unreferenced|date=March 2009}}
{{Unreferenced|date=March 2009}}
The '''Bell 202 modem''' was an early [[modem]] developed by [[AT&T]]. It used [[audio frequency-shift keying]] to encode and transfer data at a rate of 1,200 [[bits per second]], [[Duplex (telecommunications)#Half-duplex|half-duplex]] (one-way). Other third party modems that support the same signalling and are referred to generically as "Bell 202 modulation", and any device employing it as "Bell 202-compatible" or "a Bell 202 modem".
The '''Bell 202 modem''' was an early [[modem]] developed by [[AT&T]]. It used [[audio frequency-shift keying]] to encode and transfer data at a rate of 1200 [[bits per second]], [[Duplex (telecommunications)#Half-duplex|half-duplex]] (one-way). This signalling protocol, also used in third-party modems, is referred to generically as ''Bell 202 modulation'', and any device employing it as ''Bell-202-compatible''.


* Bell 202 uses 1,200 Hz for the mark (typically a binary '1') tone and 2,200 Hz for the space (typically a binary '0') tone.
* Bell 202 uses a 1200 Hz tone for ''mark'' (typically a binary ''1'') and 2200 Hz for ''space'' (typically a binary ''0'').


In [[North America]] (and perhaps elsewhere), Bell 202 modulation is used to transmit [[Caller ID]] information on the [[Public Switched Telephone Network|public telephone network]]. It is also employed in some commercial settings.
In [[North America]] (and perhaps elsewhere), Bell 202 modulation is used to transmit [[Caller ID]] information over [[Plain_old_telephone_service|POTS lines]] in the [[Public Switched Telephone Network|public telephone network]]. It is also employed in some commercial settings.


Surplus Bell 202 modems were used by [[amateur radio]] operators to construct the first [[packet radio]] stations, and despite its low [[data signaling rate|signalling speed]], Bell 202 modulation remains the standard for amateur [[VHF]] operation in most areas. Notably, [[Automatic Position Reporting System]] transmissions are most often encoded this way.
Surplus Bell 202 modems were used by [[amateur radio]] operators to construct the first [[packet radio]] stations, and despite its low [[data signaling rate|signalling speed]], Bell 202 modulation remains the standard for amateur [[VHF]] operation in most areas. Notably, [[Automatic Position Reporting System]] transmissions are most often encoded this way.

Revision as of 22:25, 25 April 2009

The Bell 202 modem was an early modem developed by AT&T. It used audio frequency-shift keying to encode and transfer data at a rate of 1200 bits per second, half-duplex (one-way). This signalling protocol, also used in third-party modems, is referred to generically as Bell 202 modulation, and any device employing it as Bell-202-compatible.

  • Bell 202 uses a 1200 Hz tone for mark (typically a binary 1) and 2200 Hz for space (typically a binary 0).

In North America (and perhaps elsewhere), Bell 202 modulation is used to transmit Caller ID information over POTS lines in the public telephone network. It is also employed in some commercial settings.

Surplus Bell 202 modems were used by amateur radio operators to construct the first packet radio stations, and despite its low signalling speed, Bell 202 modulation remains the standard for amateur VHF operation in most areas. Notably, Automatic Position Reporting System transmissions are most often encoded this way.

The ITU-T V.23 communications standard defines a similar modulation scheme.

See also