Water softening

Water softening is the act of reducing the dissolved calcium, magnesium, and to some degree manganese and ferrous iron ion concentration in hard water. A common water softener is sodium carbonate (Template:SodiumTemplate:Carbonate).

These "hardness ions" cause three major kinds of undesired effects. Most visibly, metal ions react with soaps and calcium-sensitive detergents, hindering their ability to lather and forming a precipitate—the familiar "bathtub ring". Presence of "hardness ions" also inhibits the cleaning effect of detergent formulations.

Second, calcium and magnesium carbonates tend to precipitate out as hard deposits to the surfaces of pipes and heat exchanger surfaces. This is principally caused by thermal decomposition of bi-carbonate ions but also happens to some extent even in the absence of such ions. The resulting build-up of scale can restrict water flow in pipes. In boilers, the deposits act as an insulation that impairs the flow of heat into water, reducing the heating efficiency and allowing the metal boiler components to overheat. In a pressurized system, this can lead to failure of the boiler. The damage caused by calcium carbonate deposits vary depending on the crystalline form, for example, calcite or aragonite.

Third, the presence of ions in an electrolyte, in this case, hard water, can also lead to galvanic corrosion, in which one metal will preferentially corrode when in contact with another type of metal, when both are in contact with an electrolyte. However the sodium (or potassium) ions released during conventional water softening are much more electrolytically active than the calcium or magnesium ions that they replace and galvanic corrosion would be expected to be substantially increased by water softening and not decreased. Similarly if any lead plumbing is in use, softened water is likely to be substantially more plumbo-solvent than hard water.

Ion-exchange resin devices

Conventional water-softening appliances intended for household use depend on an ion-exchange resin in which "hardness" ions trade places with sodium ions that are electrostatically bound to the anionic functional groups of the polymeric resin. A class of minerals called zeolites also exhibits ion-exchange properties; these minerals were widely used in earlier water softeners. Water softeners may be desirable when the source of water is a well, whether municipal or private.

How it works

The water to be treated passes through a bed of the resin. Negatively-charged resins absorb and bind metal ions, which are positively charged. The resins initially contain univalent hydrogen, sodium or potassium ions, which exchange with divalent calcium and magnesium ions in the water. As the water passes through the resin column, the hardness ions replace the hydrogen, sodium or potassium ions which are released into the water. The "harder" the water, the more hydrogen, sodium or potassium ions are released from the resin and into the water.

Resins are also available to remove carbonate, bi-carbonate and sulphate ions which are absorbed and hydroxyl ions released from the resin. Both types of resin may be provided in a single water softener.

Regeneration

As these resins become loaded with undesirable cations and anions they gradually lose their effectiveness and must be regenerated. If a cationic resin is used (to remove calcium and magnesium ions) then regeneration is usually effected by passing a concentrated brine, usually of sodium chloride or potassium chloride, or hydrochloric acid solution through them.

For anionic resins a solution of sodium or potassium hydroxide (lye) is used. Most of the salts used for regeneration get flushed out of the system and may be released into the soil or sewer. These processes can be damaging to the environment, especially in arid regions. Some jurisdictions prohibit such release and require users to dispose of the spent brine at an approved site or to use a commercial service company. Most water softener manufacturers provide metered control valves to minimize the frequency of regeneration. It is also possible on most units to adjust the amount of reagent used for each regeneration. Both of these steps are recommended to minimize the impact of water softeners on the environment and conserve on reagent use. Using acid to regenerate lowers the pH of the regeneration waste.

In industrial scale water softening plants, the effluent flow from re-generation process can be very significant. Under certain conditions, such as when the effluent is discharged in admixture with domestic sewage, the calcium and magnesium salts may precipitate out as hardness scale on the inside of the discharge pipe. This can build up to such an extent so as to block the pipe, as happened to a major chlor-alkali plant on the south Wales coast in the 1980s.

If potassium chloride is used, the same exchange process takes place, except that potassium is exchanged for the calcium, magnesium and iron instead of sodium. This is a more expensive option and may be unsuited for people on potassium-restricted diets.

In residential or small commercial softeners. salt bridges and salt cakes can easily occur if no routine maintenance is performed. This could be done by poking a broom handle down the salt tank to break up salt clumps and bridges. Also, every so often, salt should be emptied out of the tank, and the sides of the brine tank should be wiped down with a dilluted vinegar/water solution.

Effects of sodium

For people on a low-sodium diet, the increase in sodium levels (for systems releasing sodium) in the water can be significant, especially when treating very hard water. A paper by Kansas State University gives an example: "A person who drinks two litres (2L) of softened, extremely hard water (assume 30 gpg) will consume about 480 mg more sodium (2L x 30 gpg x 8 mg/L/gpg = 480 mg), than if unsoftened water is consumed." This is a significant amount, as they state: "The American Heart Association (AHA) suggests that the 3 percent of the population who must follow a severe, salt-restricted diet should not consume more than 400 mg of sodium a day. AHA suggests that no more than 10 percent of this sodium intake should come from water. The EPA’s draft guideline of 20 mg/L for water protects people who are most susceptible." Most people who are concerned with the added sodium in the water generally have one tap in the house that bypasses the softener, or have a reverse osmosis unit installed for the drinking water and cooking water, which was designed for desalinisation of sea water. Potassium chloride can also be used instead of sodium chloride, which would have the added benefit of helping to lower blood pressure, though for about 4 times the cost.

Chelating agents

Main article: Chelation

Chelators are used in chemical analysis, as water softeners, and are ingredients in many commercial products such as shampoos and food preservatives. Citric acid is used to soften water in soaps and laundry detergents. A commonly used synthetic chelator is EDTA.

Physical conditioners

Physical conditioners treat water by subjecting it to a magnetic field or radio waves and claim to provide similar benefits to water softening. These devices are controversial. In the UK, Southern Water's factsheet states "by the modern definition, physical conditioning does not soften water, and any such claim is incorrect. However, physical conditioning can make water seem softer". The factsheet gives detailed information on the pros and cons of physical conditioners.

See also

• Ion exchange
• Water purification
• Descaling agent
• Desalination

External links

• Wilkes University hard water site
• Riverside County CA water softener restrictions
• Water softener regeneration
• Gallery of water-related pseudoscience - Chemist's site providing explanations of how alternatives to water softening, such as catalytic water conditioning, are not scientifically grounded