Zinc alloy electroplating: Difference between revisions
hatnote |
|||
| Line 121: | Line 121: | ||
Initiated by the [[Automotive industry|Automotive Industry]], Zinc Alloys are applied for all applications where the cosmetic requirements require more than 6 years without a change in appearance and 12 years for avoiding functional corrosion. Alkaline Zn/Ni 86/14 has a microhardness of 450 HV15 and can replace hard steel components for various equipment manufacturers. Besides Automotive, Electrical, House Building, Aerospace, Fastener Industries all find benefits from Zinc Alloys. |
Initiated by the [[Automotive industry|Automotive Industry]], Zinc Alloys are applied for all applications where the cosmetic requirements require more than 6 years without a change in appearance and 12 years for avoiding functional corrosion. Alkaline Zn/Ni 86/14 has a microhardness of 450 HV15 and can replace hard steel components for various equipment manufacturers. Besides Automotive, Electrical, House Building, Aerospace, Fastener Industries all find benefits from Zinc Alloys. |
||
== |
==References== |
||
{{reflist}} |
{{reflist}} |
||
Revision as of 01:46, 31 August 2011
Zinc alloys have been developed for meeting the most challenging specifications in terms of corrosion protection, temperature and wear resistance.
History
The modern development started during the 80’s with the first alkaline Zn/Fe (99,5%/0,5%) deposits and Zn/Ni (94%/6%) deposits. Recently, the reinforcement of the corrosion specifications of the major European Car Makers and the Directive ELV that banished the use of hexavalent Chromium (CrVI) Conversion Coating required greater use of alkaline Zn/Ni between 12 and 15% of Ni (Zn/Ni 86/14).[1] Only Zn/Ni (86%/14%) is an alloy while lower content of Iron, Cobalt and Nickel leads to co-deposits. Zn/Ni (12%-15%) in Nickel in acidic and alkaline electrolytes is plated as the gamma crystalline phase of the binary diagram Zn-Ni.
Processes
The corrosion protection is primarily due to the anodic potential dissolution of zinc versus iron. Zinc is acting as sacrificial anode for protecting iron (steel). While steel is close to -400 mV, depending on alloy composition, electroplated zinc is much more anodic with -980 mV. Steel is preserved from corrosion by cathodic protection. When alloying zinc with cobalt or nickel at levels less than 1% has minimal affect on the potential but both alloys improve the capacity of the zinc layer to develop a chromate film by conversion coating. This enhances corrosion protection further. On the opposite Zn/Ni between 12% and 15% of Ni (Zn/Ni 86/14) has a potential around -680 mV closer to Cadmium -640 mV. During corrosion, the attack of zinc is preferred and the dezincification leads to a consistent increase of the potential towards steel. Thanks to this mechanism of corrosion, this alloy offers much greater protection than all other alloys.
For cost reasons the existing market is dividing between alkaline Zn/Fe (99,5%/0,5%) and alkaline Zn/Ni (86%/14%). The use of former alkaline and acidic Zn/Co (99,5%/0,5%) is disappearing from the specifications because Fe gives similar results with less environmental concern. The former Zn/Ni (94%/6%) that was a blend between pure zinc and the crystallographic gamma phase of Zn/Ni (86%/14%), was withdrawn from the European specs. A specific advantage of alkaline Zn/Ni (86%/14%) involves the lack of hydrogen embrittlement by plating. It was proved that the first nucleation on steel starts with pure nickel and that this layer is plated 2 nm thick prior to the Zn-Ni.[2] This initial layer prevents hydrogen from penetrating deep into the steel substrate thus avoiding the serious problems associated with hydrogen embrittlement. The value of this process and the initiation mechanism is quite useful for hard strength steel, tool steels and other substrates susceptible to hydrogen embrittlement.
A new acidic Zn/Ni (86%/14%) has been developed that produces brighter deposit but offers less metal distribution than the alkaline system and without the aforementioned Nickel underlayer, does not offer the same performance in terms of hydrogen embrittlement. Additionally, all the zinc alloys receive the new CrVI free conversion coating films that are frequently followed by a top-coat to enhance corrosion protection, Wear resistance and to control the coefficient of friction.
Bath compositions
- Alkaline Zinc-Iron :
| Parameters | Composition in g/L |
|---|---|
| Zinc | 6-20 |
| Iron | 0.05-0.4 |
| Caustic soda | 120 |
- Acidic Zinc-cobalt:
| Parameters | Composition in g/L |
|---|---|
| Zinc | 25-40 |
| Cobalt | 2-5 |
| Total Chloride | 130-180 |
| Potassium Chloride | 200-250 |
| Boric Acid | 25 |
- Alkaline Zinc-nickel 4-8%:
| Parameters | Composition in g/L |
|---|---|
| Zinc | 7.5-10 |
| Nickel | 1.8-2 |
| Caustic Soda | 100-120 |
- Alkaline Zinc-nickel 12-15%
| Parameters | Composition in g/L |
|---|---|
| Zinc | 7-12 |
| Nickel | 1-2.5 |
| Caustic Soda | 120 |
- Acidic Zinc-nickel 12-15%
| Parameters | Composition in g/L |
|---|---|
| Zinc | 30-40 |
| Nickel | 25-35 |
| Total Chloride | 150-230 |
| Boric Acid | 25 |
Business Fields
Initiated by the Automotive Industry, Zinc Alloys are applied for all applications where the cosmetic requirements require more than 6 years without a change in appearance and 12 years for avoiding functional corrosion. Alkaline Zn/Ni 86/14 has a microhardness of 450 HV15 and can replace hard steel components for various equipment manufacturers. Besides Automotive, Electrical, House Building, Aerospace, Fastener Industries all find benefits from Zinc Alloys.
References
- ^ http://docs.google.com/viewer?a=v&q=cache:87OBrYAgFqQJ:www.legris.com/jahia/webdav/site/legris/shared/BP/Documentation/directives_europeenes_FR.pdf+norme+ELV+chrome+6&hl=fr&gl=fr&pid=bl&srcid=ADGEEShSfDYjhdI2SITSFrmNEQUrF4jHSsXkLGJV25rKp2mtXiOq6baWdhNEgDT3H8YMs-W_rS8fMNoVrfk9B7cRzN86MAgD5kEmqZcgYuxK0wr9mzFVFtFIKKPcCOj5JqiMGAiERhyb&sig=AHIEtbQPXwhLbUJOv_JDD5R1gPps5jsnTA
- ^ "http://docs.google.com/viewer?a=v&q=cache:Y43oVXFP1zoJ:www.nasf.org/staticcontent/Duprat%2520Paper.pdf+El+Hajjami,+Besan%C3%A7on+University,+2007&hl=fr&gl=fr&pid=bl&srcid=ADGEESiVywdKzKQfP4eYg0A0hOikhglM-frWsAMvQyNzk6yGvgOTZiBlrA6MzLCPRedxzonu7ZvWzwom0S_Rfl6PycuEE_yTlEfuw8Dvv8N6eqKDP917lqVkPHah9IIxUxQmteBcrIOU&sig=AHIEtbSj1QqkGTDWmI3wLt-m3cmiEEQa7A
- JJ. Duprat(Coventya), Mike Kelly(Coventya), «Dedicated processes for electroplating on fasteners», Fasteners Technology International, August 2010, p56-60,
www.nasf.org/staticcontent/Duprat%20Paper.pdf - Pages similaires
- L. Thiery, F. Raulin : « Advances in trivalent passivates on zinc and zinc alloy », Galvanotechnik 98(4) (2007) 862-869,
http://stneasy.fiz-karlsruhe.de
- El Hajjami, M.P. Gigandet, M. De Petris-Wery, J.C. Catonné, J.J. Duprat, L. Thiery, N. Pommier, F. Raulin, B. Starck, P. Remy : « Characterization of thin Zn-Ni alloy coatings electrodeposited on low carbon steel », Applied Surface Sciences, 254, (2007) 480-489,
http://dx.doi.org/10.1016/j.apsusc.2007.06.016
- N. Pommier, L. Thiery (Coventya), M.P. Gigandet, M. Tachez : « Electrochemical study of the degradation of an organomineral coating: polarization resistance and electrochemical impedance spectroscopy measurements » , Ann. Chim. Sci. Mat, 1998, 23, 397-400,
http://dx.doi.org/10.1016/j.apsusc.2007.06.016
- Modern Electroplating, 5th Edition,
http://media.wiley.com/product_data/excerpt/46/04711682/0471168246.pdf
- H. Geduld, «Zinc Plating», Finishing Publications, 1988,
http://www.amazon.com/Zinc-Plating-Herb-Geduld/dp/090447710X
- K. Wojczykowski, «New Developments in Corrosion Testing: Theory, Methods and Standards», Surfin proceedings 2010, Grand Rapids, MI, session 7,
http://www.nasf.org/staticcontent/WojczykowskiNewDevelopmentsPres.pdf
- A. Jimenez, «Membrane Technology for electroplating processes», Surfin proceedings 2010, Grand Rapids, MI, session 4,
http://www.nasf.org/staticcontent/JimenezMembraneTechnologyPap.pdf