Rotary dial: Difference between revisions
No edit summary |
mNo edit summary |
||
| Line 6: | Line 6: | ||
Some telephone sets include a much smaller dial inside the handset, with a movable finger stop that the user is to press against, while rotating the dial clockwise, until the finger stop itself moves no longer, then release both. In this setting, there is no section of the rotating dial plate that does not have holes. One example of this design is the [[Nortel Networks|Northern]] Electric Company/Northern Telecom (now Nortel) ''Contempra'' (TM) set. |
Some telephone sets include a much smaller dial inside the handset, with a movable finger stop that the user is to press against, while rotating the dial clockwise, until the finger stop itself moves no longer, then release both. In this setting, there is no section of the rotating dial plate that does not have holes. One example of this design is the [[Nortel Networks|Northern]] Electric Company/Northern Telecom (now Nortel) ''Contempra'' (TM) set. |
||
Many phone lines no longer recognize pulse dialing, however, and it often has to be ordered separately from a phone company. The shorter dialing times possible for tone dialing added to the shift away from pulse dialing, which |
Many phone lines no longer recognize pulse dialing, however, and it often has to be ordered separately from a phone company. The shorter dialing times possible for tone dialing added to the shift away from pulse dialing, which has been largely abandoned in many places now. An exception to this rule is the United States, where telephone lines use both tone and pulse dialing. The US Telephone system allows numbers to be dialed in either system, you can even change systems between digits and still dial correctly. The slower adoption of tone dialing in the US was due in part to the fact that tone dialing was an "option" with an additional charge. |
||
Different pulse systems are used depending on which country you are in. [[Sweden]] uses 1 pulse to signal the number zero, and 10 pulses to signal the number nine. [[New Zealand]] uses ten pulses minus the number desired; so to dial 7, the hook must be pressed three times. In [[Norway]], the North American system with the number 1 corresponding to one pulse was used, except from the capital, [[Oslo]], which used the same "inverse" system as in New Zealand. For this reason, the numbers on the dial are shifted in different countries, or even in different areas of one country, to work with their system because of the difference of the number arrangement on the dial. |
Different pulse systems are used depending on which country you are in. [[Sweden]] uses 1 pulse to signal the number zero, and 10 pulses to signal the number nine. [[New Zealand]] uses ten pulses minus the number desired; so to dial 7, the hook must be pressed three times. In [[Norway]], the North American system with the number 1 corresponding to one pulse was used, except from the capital, [[Oslo]], which used the same "inverse" system as in New Zealand. For this reason, the numbers on the dial are shifted in different countries, or even in different areas of one country, to work with their system because of the difference of the number arrangement on the dial. |
||
Revision as of 16:58, 18 April 2006
The rotary dial is a device mounted on or in a telephone or switchboard that is designed to send interrupted electrical pulses, known as pulse dialing, corresponding to the number dialled. It was invented in 1888 by Almon Strowger. The device was phased out from the 1970s onwards, with the onset of touch tone dialing and which used a telephone keypad instead of a dial.
The dial is circular, about 78 mm (3 inches) in diameter, with 10 finger holes cut through the outer perimeter. The dial is mounted via a shaft extending from inside the phone or mounting and sits approximately 6 mm (¼ inch) above a faceplate. The faceplate is set so that through each finger hole letters and numbers printed on the faceplate may be seen. In North America, traditional dials have letter codes displayed with the numbers under the finger holes in the following pattern: 1, 2 ABC, 3 DEF, 4 GHI, 5 JKL, 6 MNO, 7 PRS, 8 TUV, 9 WXY and 0 Operator. However, such letter codes were not used in all countries. The illustration shows a UK dial. Older Australian rotary dial phones had them, but the letter combinations were often printed in the centre plate adjacent to the number. The 1 is normally set at approximately 60 degrees clockwise from the uppermost point of the dial (if one imagines an analogue clock face over the dial, the 1 is located at approximately the 2 o'clock position), and then the numbers progress upward counterclockwise, with the 0 being at about 5 o'clock. A curved device called a finger stop sits above the dial at the 4 o'clock position. To dial a 6, the user puts a finger in the 6 finger hole and rotates the dial clockwise until it reaches the finger stop. The user then pulls out the finger, and a spring in the dial returns it to the resting position. As the dial returns, electrical contacts wired through the mechanism underneath will open and close 6 times, thus sending 6 pulses to the receiving end. A centrifugal governor regulates the speed at which the dial returns under the force of the spring.
Some telephone sets include a much smaller dial inside the handset, with a movable finger stop that the user is to press against, while rotating the dial clockwise, until the finger stop itself moves no longer, then release both. In this setting, there is no section of the rotating dial plate that does not have holes. One example of this design is the Northern Electric Company/Northern Telecom (now Nortel) Contempra (TM) set.
Many phone lines no longer recognize pulse dialing, however, and it often has to be ordered separately from a phone company. The shorter dialing times possible for tone dialing added to the shift away from pulse dialing, which has been largely abandoned in many places now. An exception to this rule is the United States, where telephone lines use both tone and pulse dialing. The US Telephone system allows numbers to be dialed in either system, you can even change systems between digits and still dial correctly. The slower adoption of tone dialing in the US was due in part to the fact that tone dialing was an "option" with an additional charge.
Different pulse systems are used depending on which country you are in. Sweden uses 1 pulse to signal the number zero, and 10 pulses to signal the number nine. New Zealand uses ten pulses minus the number desired; so to dial 7, the hook must be pressed three times. In Norway, the North American system with the number 1 corresponding to one pulse was used, except from the capital, Oslo, which used the same "inverse" system as in New Zealand. For this reason, the numbers on the dial are shifted in different countries, or even in different areas of one country, to work with their system because of the difference of the number arrangement on the dial.
Note: Not all phone systems and phones support this method.
Tapping
It is possible to trick a phone system into thinking that a rotary dial is being used. To do this, one finds the little button, switch, or hook that is pushed down when you hang up the phone. To "dial" the digit 1, tap it once. For the digit 2, tap it twice QUICKLY (ten taps per second for UK phones and in North America). For the digit 3, use three taps, etc. The digit 0 is ten taps. (But see above if you are in Sweden, New Zealand or Oslo.) Some models of keypad phones also have a tone/pulse switch which can be toggled to switch between the two.
In the UK it used to be possible to make calls for free from coin-box phones (payphones) by tapping. This was on phones with A and B button boxes. (These were phased out between 1958 and 1979 as subscriber trunk dialling was introduced.) A person caught tapping could be charged with 'stealing electricity from the GPO'.