Backfeeding: Difference between revisions
Reify-tech (talk | contribs) Copyedit clarification |
Reify-tech (talk | contribs) Better wording |
||
| Line 4: | Line 4: | ||
==Description== |
==Description== |
||
By definition, backfeeding causes [[electrical power]] to flow in the opposite direction from its usual flow. When studying backfeeding, engineers must |
By definition, backfeeding causes [[electrical power]] to flow in the opposite direction from its usual flow. When studying backfeeding, engineers must understand the ''transfer of electrical power'', and not confuse this with momentary AC voltages or current flows viewed in isolation from the overall situation. |
||
<!-- Following is technically misleading and confusing, because normal AC voltage always alternates positive and negative. What matters is the flow of *power*, not the momentary flow of current. --> |
<!-- Following is technically misleading and confusing, because normal AC voltage always alternates positive and negative. What matters is the flow of *power*, not the momentary flow of current. --> |
||
<!-- An alternating current (AC) [[power station]] typically delivers power to the [[power grid]] by inducing a [[current (electricity)|current]] to flow into the power grid when the voltage is positive, and inducing it to flow out of the power grid when the voltage is negative, and a typical power grid load (e.g. factory or home) induces current to flow out of the power grid when the voltage is positive and into the power grid when the voltage is negative. If either of these types of facilities starts inducing current like the other, then backfeeding is occurring. --> |
<!-- An alternating current (AC) [[power station]] typically delivers power to the [[power grid]] by inducing a [[current (electricity)|current]] to flow into the power grid when the voltage is positive, and inducing it to flow out of the power grid when the voltage is negative, and a typical power grid load (e.g. factory or home) induces current to flow out of the power grid when the voltage is positive and into the power grid when the voltage is negative. If either of these types of facilities starts inducing current like the other, then backfeeding is occurring. --> |
||
Revision as of 14:14, 28 March 2017
 |
 | This article needs attention from an expert on the subject. The specific problem is: Needs expansion, with reliable references. (March 2017) |
Backfeeding is flow of electrical energy in the reverse direction from its normal flow. For example, backfeeding may occur when electrical power is injected into the local power grid from a source other than a utility company generator.
Description
By definition, backfeeding causes electrical power to flow in the opposite direction from its usual flow. When studying backfeeding, engineers must understand the transfer of electrical power, and not confuse this with momentary AC voltages or current flows viewed in isolation from the overall situation.
Power grid generators normally pump energy into the grid, making it available for others to use. A power station will typically backfeed (and thus consume power) when it is shut down, due to its own local loads (e.g. lights or repair equipment).
Power grid loads may backfeed if they also have distributed generation installed, such as a grid-connected photovoltaic solar power system or a microturbine-based power generator. It is also possible for an electric motor to temporarily backfeed if it is mechanically driven (see regenerative braking).
Design considerations
For cost reasons, many of the circuit (overcurrent) protection and power quality control (voltage regulation) devices used by electric utility companies are designed with the assumption that power always flows in one direction. An interconnection agreement can be arranged for equipment designed to backfeed between an electric utility customer with distributed generation and their power company. This type of interconnection can involve nontrivial engineering, and possibly equipment upgrade costs to keep the distribution circuit properly protected. Such costs may be minimized by limiting distributed generation capacity to less than is locally consumed, and guaranteeing this condition by installing a reverse-power cutoff relay that opens if backfeeding occurs.
Hazards
Because it involves transfer of significant amounts of energy, backfeeding must be carefully controlled and monitored. Personnel working on equipment subject to backfeeding must be aware of all possible power sources, and follow systematic protocols to ensure that equipment is fully de-energized before commencing work, or use special equipment and techniques suitable for working on live equipment.
