::The Calcutta accident was almost certainly caused by what is now known as [[wind-shear]] or [[clear air turbulence]] as the aircraft had just flown through a thunderstorm. The CP accident was caused by the pilot over-rotating on take-off and stalling the aircraft on the runway. The Comet design had been successfully flying for three years previously without anyone managing to do this. The accident was probably caused by the accident pilot's unfamiliarity with a swept wing.
::The Calcutta accident was almost certainly caused by what is now known as [[wind-shear]] or [[clear air turbulence]] as the aircraft had just flown through a thunderstorm. The CP accident was caused by the pilot over-rotating on take-off and stalling the aircraft on the runway. The Comet design had been successfully flying for three years previously without anyone managing to do this. The accident was probably caused by the accident pilot's unfamiliarity with a swept wing.
::BTW, if metal fatigue had not been the cause de Havilland's would not have 'wasted' a number of years on the Comet's re-design, nor on restricting existing Comet I's to flying un-pressurised, or rather expensively scrapping them. <!-- Template:Unsigned IP --><small class="autosigned">— Preceding [[Wikipedia:Signatures|unsigned]] comment added by [[Special:Contributions/95.150.11.183|95.150.11.183]] ([[User talk:95.150.11.183#top|talk]]) 13:20, 28 June 2017 (UTC)</small> <!--Autosigned by SineBot-->
::BTW, if metal fatigue had not been the cause de Havilland's would not have 'wasted' a number of years on the Comet's re-design, nor on restricting existing Comet I's to flying un-pressurised, or in rather expensively scrapping them. <!-- Template:Unsigned IP --><small class="autosigned">— Preceding [[Wikipedia:Signatures|unsigned]] comment added by [[Special:Contributions/95.150.11.183|95.150.11.183]] ([[User talk:95.150.11.183#top|talk]]) 13:20, 28 June 2017 (UTC)</small> <!--Autosigned by SineBot-->
Revision as of 15:28, 28 June 2017
This is the talk page for discussing improvements to the De Havilland Comet article. This is not a forum for general discussion of the article's subject.
This article is within the scope of the Aviation WikiProject. If you would like to participate, please visit the project page, where you can join the project and see lists of open tasks and task forces. To use this banner, please see the full instructions.AviationWikipedia:WikiProject AviationTemplate:WikiProject Aviationaviation
This article is within the scope of the Military history WikiProject. If you would like to participate, please visit the project page, where you can join the project and see a list of open tasks. To use this banner, please see the full instructions.Military historyWikipedia:WikiProject Military historyTemplate:WikiProject Military historymilitary history
This article is within the scope of WikiProject United Kingdom, a collaborative effort to improve the coverage of the United Kingdom on Wikipedia. If you would like to participate, please visit the project page, where you can join the discussion and see a list of open tasks.United KingdomWikipedia:WikiProject United KingdomTemplate:WikiProject United KingdomUnited Kingdom
This article is written in British English, which has its own spelling conventions (colour, travelled, centre, defence, artefact, analyse) and some terms that are used in it may be different or absent from other varieties of English. According to the relevant style guide, this should not be changed without broad consensus.
I just made an edit mentioning why square windows are bad: stress concentration. I'd like to be a little more specific about the problem: Were the engineers unfamiliar with stress concentration, or did they know of it and underestimate it? Seems that the latter is more likely.
De Havilland did undertake fuselage pressurisation tests in their water tank and these revealed that there was a potential fatigue failure at the corner of the cabin window that could lead to a complete failure of the pressure cabin. Their report, issued in 1953, recommended no further remedial cation needed as the pressure applied in the water tank were far in excess if what would be encountered in normal service.
(De Havilland Comet p67...K Darling.. Crowood Press 2004) Didn't help that the roof mounted ADF panel was also square.. Lynx707 (talk) 11:29, 28 July 2008 (UTC)[reply]
The Comet's pressure cabin was designed according to the best design practices of the time, and was in fact, designed to far exceed the-then CAA strength requirements, something like twice that which was considered necessary. Commercial aircraft pressure cabins had never undergone comprehensive stress measurements, or at least, had been designed based on estimates of predicted loads, rather than measured loads, and worldwide all designs were based on these or similar stress calculations. After the accidents when a test Comet was flown with the cabin fitted-out with a considerable number of strain gauges, it was only then discovered how much the stress concentrations differed in certain areas (such as the corners of the cabin windows) from that which had been predicted, and which all previous pressurised cabins had been based-on. In short, the theory had been in error (or rather, incomplete), and it was only the accidents to the Comet that showed this up. The point about using a thinner-gauge of cabin skinning than on previous pressurised cabin airliners is that, by what was known about fatigue and pressure cabins at the time, it SHOULD have still been perfectly safe.
The square windows had been specified by the customers, as passengers preferred them, and if you look at contemporary pressurised piston-engined airliners, e.g., Boeing Stratocruiser, Douglas DC-6 C-97 Stratofreighter pictured as the Stratocruiser article only has images of the later round-windowed aircraft you can see they had square windows too. They were only changed to rounded ones after the Comet crashes. (Avro had originally designed the Tudor with circular windows but the customer (BOAC) made them change them, which was one of the reasons the Tudor was so late and over-budget, as they had to change all the ones already built. Avro then had to change them all back to circular windows after the Comet crashes).
Before the Comet they had never been a problem, as the piston-engined airliners flew at lower altitudes, and so the pressure differentials were also lower, and fatigue had never been such a factor. In effect, the Comet's cabin expanded-and-contracted when it climbed-and-descended to a much greater extent than in previous aircraft (not helped by the thinner-gauge fuselage skinning), which, unexpectedly, greatly increased the fatigue effect. The water pressure test that de Havilland had subjected the cabin-to during the designing of the aircraft had been carried out on only a section of the cabin, and unfortunately the plugs at either end (that sealed off the cabin test section to make it watertight) had been contributing more than had been allowed-for in the ultimate strength and rigidity of the test section. So the test wasn't actually representative of the complete fuselage. All this wasn't known until after the accidents, and it's hard to see how, with the state of the knowledge they then had, it could have been predicted, as the Comet was at the time the most comprehensively tested airliner then-built.
It was bad luck, that's all, and de Havilland passed-on all the conclusions about the new factors that had to be taken into account in safe pressure cabin design that now make cabin failure almost unknown in today's airliners. As someone said, if it hadn't happened to de Havilland, it would almost certainly have happened to someone else. —Preceding unsigned comment added by 213.40.254.27 (talk) 21:40, 2 October 2009 (UTC)[reply]
A missing link? The article says the windows were supposed to be rivetted and glued, but in the end, only rivetted. This seems a crucial ommission, and I would expect the report to at least mention responsibility for this failure. It might be a good idea to try and source the responsibility for that fatal decision. (It sounds like a typical management thing; it's okay just rivetted; we need to go faster; so screw the second requirement, let's just get on with it, that sort of rationalization.) Still, I for one would like to know who made that choice, and whether it was the final mistake in a chain of mistakes.24.81.25.127 (talk) 17:09, 5 August 2010 (UTC)[reply]
"The square windows had been specified by the customers, as passengers preferred them, and if you look at contemporary pressurised piston-engined airliners, e.g., Boeing Stratocruiser, Douglas DC-6 you can see they had square windows too. They were only changed to rounded ones after the Comet crashes." B377 customers could get their windows sort-of-rectangular or circular, but none were ever changed, were they? And all DC-6/DC-7/L1049/L1649 windows were sort-of-rectangular, from 1947 thru the end of production in 1958? Wasn't their corner radius much greater than the Comet's? Tim Zukas (talk) 16:43, 15 September 2010 (UTC)[reply]
The article says the windows were supposed to be rivetted and glued, but in the end, only rivetted. - it probably wouldn't have made much difference, just perhaps extended the time before the failure occurred. The Comet's pressure cabin although designed to be safe and strong enough, had almost no fatigue life, i.e., it was strong enough when new, but each pressurization/depressurization cycle weakened it far more than had ever been anticipated. This problem had never been seen before as earlier piston-engined pressurized airliners didn't fly high enough for the pressure differential to be as great as on the Comet, which was intended for flight at 40,000ft to allow the best efficiency of the jet engines to be attained.
Fatigue had never been much of a problem before the Comet simply because few airframes had managed to rack-up the flying hours that the then-new jet airliners were capable of. Prior to World War II the world's airlines simply didn't use their aircraft as intensely as occurred during the rapid expansion of mass air travel that happened in the years after the end of the war. The only other large aircraft that might have been prone to metal fatigue, large military transports and bombers, usually didn't last long enough on operations to get to the point where fatigue problems arose - they usually got lost in accidents or were shot down - smaller, high-performance aircraft like fighter aeroplanes, are designed to much higher load factors, so are much stronger in the first place. The other point is that for these other large military aeroplanes, the economic factor didn't really apply, so the designers didn't need to be so weight-conscious in the design, whereas for the commercial airlines, the driving force is whether the airline can make a profit - if you can save say, 250lb in airframe weight, that's another passenger and his/her luggage you can carry - and an additional fare. As a result of this, aircraft designers began to design aeroplanes that were just strong enough, any additional strengthening being unnecessary weight, reducing the actual paying load (payload) that could be carried. This affected profitability for the airline, and so it became the norm to design aircraft that (compared to the earlier ones) were much less robust compared to their weight. This can be seen in the various modern jet airliner accidents, where little remains of the aircraft involved in a crash, the aeroplane in-effect, disintegrating. Earlier piston-engined airliners usually remain recognisable as airliners after crashes, providing there is no fire.
With hindsight, de Havilland probably carried the weight reduction too far, but that was necessitated by the relatively low-powered engines then available. At the time they probably should have gone for the Rolls-Royce Nene, but that was made by a competitor, and so DH chose their own Ghost engine. The alternative was to have waited five or ten years for more powerful engines, but then again, the UK Government had asked for a jet airliner as early as 1944, so de Havilland went ahead and made one. Whether anyone else would have discovered how to make safe and light high-cycle pressure cabins without the Comet accidents to guide them who knows. But the Comet is one of the reasons why passenger aircraft nowadays have safe 'fatigue life' figures. —Preceding unsigned comment added by 86.112.58.103 (talk) 18:22, 2 February 2011 (UTC)[reply]
At the time, the late 1940s, de Havilland had to use the Ghost as, with the possible exception of the Derwent, it was the only jet engine anywhere that was certificated for civilian use.
An additional hard lesson was learned regarding the testing of the prototypes. The hulls used for the fatigue tests were the same hulls that had prior use in the over-pressure tests. The over-pressure tests plastically deformed the metal at the points of high stress concentration. When the pressure load was released, those plastically deformed areas contained a subsequent residual compressive strain. Those residual compressive strains greatly enhanced the fatigue resistance in those areas, and the subsequent fatigue tests then produced misleading results. Modern practice requires the over-pressure test and the fatigue test be conducted with two different hulls. When the de Havilland went into production, the new hulls naturally were not subjected to an over-pressure test first. These pristine hulls did not have any residual compressive strains in the areas of stress concentration and thus were far more sensitive to fatigue failure than the early, extensively tested prototype hulls. If pristine hulls had been used for the early fatigue tests, the problem would have manifested itself clearly.LKaczorowski (talk) 22:45, 21 May 2014 (UTC)[reply]
___________________________
Square window myth
A note about the whole square windows thing: This is largely a myth that has probably been perpetuated by a superficial reading of the accident report many years ago and has gained a life of its own.If you read the original accident report you will note that the failure in Yoke Peter did not originate at a window. It originated at the ADF panel in the fuselage crown behind the cockpit. A careful reading of the report shows that all of the cut-outs in the fuselage were under strength due to lack of knowledge at the time. The report never says that that the 'square' windows were primary or even secondary contributing factors. In fact the fatigue that brought down G=ALYP originated in a bolt hole near the ADF antenna cut-out and travelled in two directions effectively unzipping a section of the fuselage. A close examination of the photo of the tank test failure involving G-ALYU shows that the window frame did not fail but rather the escape hatch assembly failed due to insufficient reinforcing of the cut out. In the photo you can clearly see that the window frame is intact but that the escape hatch failed after the surrounding ribs and stringers fractured. Further, Yoke Peter contained a number of cracks that were created during manufacture and these had been 'located' or stop drilled and signed off. This highlights the lack of understanding at the time, of the rapid progression of pressurisation cycle fatigue effects on aircraft structures. The aircraft went into service with cracks already present in the structure!
Lastly to drive a stake through this 'square window myth', a close look at the radius of the window corners of a Comet 1 shows them to be quite similar to modern airliner windows.
In short, the fatigue failure and crash of G-ALYP was absolutely not caused by 'square windows' nor did the fatigue failure originate at any window location. If the subsequent structural strengthening has been carried out with the identical design of window - no further failures would have occurred. To drive this point home, have a look at the window of the Caravelle. They are triangular! As someone with undergraduate and a postgraduate qualifications in aircraft accident investigation and who lectures aviation safety - these old myths drive me nuts! Anyway I hope this helps. Enjoy! Completeaerogeek (talk) 08:40, 5 March 2016 (UTC)[reply]
I can see you have just about had it with square windows and I don't mean to try your patience. Not the cause of G-ALYP. I see that.
However, all the catastrophic crack growth on the water tank test fuselages, G-ALYU and YR, originated in the corner regions of windows and escape hatches where the stress levels due to their "squareness" were already high even before putting rivet holes in, see para 12, page 38. See also Behaviour of Skin Fatigue Cracks at the Corners of Windows in a Comet I Fuselage Report R&M 3248. So based on the above it seems like the Comet I's square windows, with their own unique mix of squareness and lack of redeeming features, were an accident waiting to happen on every aircraft except YP.Pieter1963 (talk) 00:26, 22 January 2017 (UTC)[reply]
I do agree about myths. For example one of the Electra crashes was due to a control cable failure, not whirl mode. The Comet 1 had square windows of about 144sqin, a bit bigger than normal for the time. The post-grounding hydrostatic tests showed cracks at window corners and at the front escape hatch. The pressure loading on the hull was simulated during design, but not with aerodynamic buffeting experienced at 300+ KIAS applied at the same time. That is why the initial fatigue testing did not give correct predictions.220.244.73.170 (talk) 10:18, 29 June 2016 (UTC)[reply]
"South Atlantic" flights
Anybody know what this is referring to?
"Although these [Comet 2] aircraft performed well on the South Atlantic routes..."
I have just checked Jackson's British civil aircraft and it mentions the Comet 2s were ordered for the South Atlantic route and that trails showed it had suitable range for the South Atlantic route but not the North Atlantic. It does not explain any further. It may just mean the southern routes to the states rather than via Iceland. MilborneOne (talk) 21:52, 9 October 2010 (UTC)[reply]
Yes, "the South Atlantic routes" would mean Dakar to Brazil; the article gives the impression the Comet 2 went into service on that route, which it didn't. Tim Zukas (talk) 22:23, 10 October 2010 (UTC)[reply]
As part of a plan for two all-British services spanning the globe The southern route would have two spurs - one to Lisbon, Dakar, across the South Atlantic to Recife (Brazil) and then following the existing BOAC South American route to Rio de Janeiro, Montevideo, Buenos Aires and Santiago. (Times 1952) so it looks like it was planned to operate a South Atlantic route. So the comment about them being ordered for the South Atlantic route appears to be correct. MilborneOne (talk) 13:10, 11 October 2010 (UTC)[reply]
In September 1953 a Comet operated a trial flight to South America in preparation for the introduction by BOAC next year of a jet airliner service between the United Kingdom and South American countries.. As the Comet 2 did not enter service following the Comet 1 crashes I suspect the plan was abandoned. MilborneOne (talk) 13:38, 11 October 2010 (UTC)[reply]
What's in a name?
2 things, since this has clearly gotten too complicated to explain in an edit summary. One, I do know Jetliner was proprietary & was generecized. It was also a neologism coined specifically for the C.102, if what little I've read is correct. (I presume that's not in question.) Also, I do know NF&L is the name now, & NF was a province then. I live in Canada, which is why I raise it: it wasn't NF&L at the time. (It got changed about, what, 10yrs ago, now? Offhand...) So is it usual to use the period-correct name, or the current one? (I default to period-correct, myself.) I'm not looking for an edit war by any means, just hoping to make it clear for the uninitiated. TREKphilerany time you're ready, Uhura 21:40, 2 November 2010 (UTC)[reply]
I think the questions are now taken care of, check the latest edits. FWiW,, Newfie land was called New and Lab in 1964 but it took until 2001 to make it official. What part of the country are you from? Bzuk (talk) 04:43, 3 November 2010 (UTC)[reply]
I'll say I'm not from NF or Lab (obviously), but Prairies... (AFAIK, the name may've been common, but for Gander, it was still officially NF only at that time; "at that time" is the issue, even if '64 is the cutoff year. Unless I've got my years very wrong.) And I'm just too tired to concentrate on finding the correct edit just now. :) If it's fixed, I'm happy. Nice work on adding all the new stuff, btw. TREKphilerany time you're ready, Uhura 23:21 & 23:28, 4 November 2010 (UTC)[reply]
Longbow hunting
Some comments.
"landmark in British aeronautical design." It seems to me it's a landmark period, no need to lim to British. I get the sense this is intended to credit Brits, & I agree; make it "British, & worldwide"? I can't think of a better way to say if offhand. :(
"too fuel-hungry and unreliable" IDK if it's on-point, but it might be good to explian why there was skepticism. Given the experience with early jet fighters, it would've seemed well-founded.
"submissions" IMO, comparisons to existing types might be of assistance here: the 2-boom resembling a Vamp, the 3-motor a crossed DC-10 & XB-70, the tailless a Vulcan, the podded a 707 (presuming that's correct).
"engine" Am I being too fussy changing that to "engined"?
"de Havilland" Maybe a trivial issue, again. Should it be "de Havillands"? I've heard that as a Brit usage for companies; the plural appears to refer to their being numerous employees.
"carrying fewer people in greater comfort" Can we mention seat pitch, here? Comparison to modern seating standards would be of interest, too, IMO: the standards at the time, as I understand it, offered much more leg room than now, even in 747s or A3xx's.
"The cabin was quieter" Is it worth explaining why? It would also help explain why jetliners attracted passenger traffic, beyond why airlines liked them (faster & cheaper to run).
Wing root engines. Did this have maintenance benefits (or drawbacks)? Ease of maintenance was one factor in Avro Canada's decision to select underslung engines. (I don't doubt podding also sees this.)
"armour for the engine cells" Was that an MoT requirement? If so, comparison to the DC-10 is in order.
"other aircraft manufacturers learned from, and profited by, de Havilland's hard-learned lessons" Is it OT to say the Comet's troubles enabled Boeing (in particular) to steal sales from DH while Comet was still a perceived hazard?
"the skin sheeting was thickened slightly" Worth mentioning how much? (Presuming it's known.)
1. Agree, the Comet has been named as one of the 50 Aircraft that Changed the World in Ron Dick and Dick Paterson's work, 2007, and one of Michael Oakey's "I00 Great British Aircraft," 2008.
2. Fuel consumption was an early "bugaboo" as characterized in From Props to Jets... (2010) p. 16.
3. Not from the preliminary design drawings I have seen, the Comet was pretty well originally all "blue sky" engineering.
4. Corrected.
5. Nope, de Havilland is correct, "de Havillands" is a common misapplication or colloquialism.
6. Can offer some dimensions but basically the BOAC Slumberseat gave more room without encroaching on overall seat area.
7. The Comet cabin was not only quiet but also was sold on the premise that it was "vibration free," the proverbial "stand-a-pen-on-its-end test.
8. Maintenance was not the primary reason for the placement of the engines, as the Comet design was intended to be as "clean" as possible for streamlining/drag reduction. Maintenance was a bit more tricky than podded engines as many service panels were involved but the engine was at least on a lower level so that no specialized equipment was needed.
9. Protection may have been required but not a MoT stipulation, but I'll check into that.
10. Boeing certainly benefited from the Comet's troubles as its B707 service introduction was relatively smooth, whether it was "sold" on that basis is a common belief, but I'll check Gunston and Yenne on that.
3. I don't mean to say there was copying. I mean, as a way to illustrate what they'd have looked like. (Unless there are free use diagrams extant? Which I doubt.)
5. Blame Brit newsies. :(
6. I was hoping for a sense of the difference between then & now, more than anything. I recall reading the C.102 having a 24" pitch, & it being said modern jetliners use more like half that. (Don't recall where, but 1 of the C.102 paeans. :) ). I should also add IDK exactly what it meant, tho "seat separation" seemed clear.
7. I believe it. The test flights of the C.102 drew a lot of comment. For those who've never flown pistons, I thought it might be an interesting comparison.
8. If not a design requirement, then an added benefit? Still might bear mentioning. (I'll leave you to decide. :) I'd put in just about everything I could find. :p)
10. I was thinking less "sold" than "took advantage", becuase, with Comets grounded, the competition was effectively gone. I doubt Boeing needed to actually say anything to poential customers, considering.
1. I think it's fair to mention that the Comet was a significant design in aviation history, it's also featured in a Jane's listing of all the "impact" designs of the 20th Century.
3.The three-engined mailplane was extremely small, with only capacity for six passengers, with a canard at the extreme end of the nose. The original tailless design has some similarity to the final Comet configuration but the wing was much larger and had a 40˚ sweep. I don't think I have ever seen the twin-boom version as a drawing. Interesting premise to see the design origins, I'll see what I can do to make up a single drawing with all the preliminary configurations.
6. I certainly agree; we have a contemporary Vickers Viscount in our local museum and the kids on tour are always amazed at the passenger space and the "huge" portal windows, quite a departure from the modern sardine-sized seating area.
7. I'll look up a quote perhaps.
8. It may or may not have been a strict requirement but de Havilland made great efforts to design a "safe" airliner, and then...
10. Boeing had pitched a faster, longer-ranging and most-of-all, a more economic fit for air carriers. The "safety factor" was probably more of a whispering campaign. FWiW Bzuk (talk) 15:01, 7 November 2010 (UTC).[reply]
1. Agree entirely. My only stumble was how to phrase it.
3. I look forward to it. (I love seeing what didn't make it. Great for us alternate historians. ;P)
6. A change in window size, too? Huh. I have a vague recollection of later jetliners going to smaller (& thicker-glass) windows...
7. Finding even a mention of the quiet & smooth compared to pistons shouldn't be hard; it seems every exec on any jet demo noticed it right away. (Or at least it does from what small amount I've read.) The difference was evidently very marked.
8. I'm betting safety was a prime concern. (What you don't think of is what tends to bite you. :( ). I'm also betting, if it wasn't expressly desired (& from what you've said, it wasn't), any ease of maintenance thanks to short gear legs was incidental. As I recall, it was deliberate in the C.102. Also, the "close pod" design avoided mucking with the wing structure, with a side effect of not needing the ground trolleys of high wings. It's that factor I suspect also incidentally fell in DH's lap.
10. I'd bet on a sort of "sideways" mention of safety, not directly saying Comets were deathtraps; I have no doubt every airline exec knew damn well how many DH108s had gone down & how many died. This would've been before the U.S. industry started the current practise, sharing out all data, wouldn't it...? So there would have been a pointed awareness of potential liability issues. (Hmmm...that might do for adding to the 707 page. I should see if I can find out.)
Who was responsible for naming this aircraft after a cascading ball of fire? It seems a poor decision in light of events. Drutt (talk) 02:10, 4 February 2011 (UTC)[reply]
BTW, there are some interesting insurance values for prototype aircraft - including the Comet - that appeared at the 1952 Farnborough air show in a 1953 issue of Flight here; [3] The quoted insured value for the Comet Mk I prototype was £500,000 (approx $2,000,000 US)
The author of the article is Capt. A. G. Lamplugh, who originated the "Aviation in itself is not inherently dangerous ..." saying. — Preceding unsigned comment added by 80.7.147.13 (talk) 20:23, 29 May 2012 (UTC)[reply]
BTW, possibly the reason Sud Aviation selected the Comet nose for the Caravelle was that de Havilland had flight tested the Comet nose profile on a full-size mock-up fitted to the nose of an Airspeed Horsa glider. — Preceding unsigned comment added by 95.149.173.74 (talk) 19:27, 16 May 2016 (UTC)[reply]
Comet rivets
Just about every article on the web concerning the de Havilland Comet mentions the use of "punch rivets" in its construction. This is widely assumed to refer to the use of what are today called "self piercing" rivets. However this cannot be the real form of riveting used on the Comet - self piercing rivets for aluminium are made from steel. Aluminium self piercing rivets have been tried but even the strongest aluminium alloys are not hard enough to pierce aerospace grade aluminium sheet. I have studied the series of articles in Flight International (Autumn 1954) which reports on the Comet inquiry and hidden in these articles is the term "skin dimpling" rivets. This form of riveting has to be used when thin aluminium sheet is being fixed to a thicker structural member and the practice is to countersink the structural member such that the rivet, when inserted, forces the thin sheet to adopt the same shape as the countersink. Obviously for thin sheet aluminium countersinking the sheet would leave it too weak. The problem with this practice is it puts the hole in the thin sheet under a circumferential tensile stress which can lead to the formation of cracks. Proper practice is to drill a hole too small, dimple the sheet into the countersink, then drill or ream the hole to remove stressed or cracked metal. Hot dimpling is also practiced to anneal the sheet prior to dimpling. Could it be that the repeated reference to punched rivets should really refer to skin dimpled rivets? By the way, according to Flight International [1], the skin dimpling method of riveting was not used in the region of the ADF window where the initial cracks were found, so all this about the method of riveting may be a red herring since the initial crack was found to start from a bolt hole I believe. Tecstrat (talk) 14:21, 29 September 2011 (UTC)[reply]
Infobox image
Greetings, and great job on this article. I think it is about ready for A-class review, if editors are interested. One possible suggestion...how about updating the infobox image? The current photo is very nice...here however is another possible choice:
The current image
Suggestion
The new image is larger, higher-res (sharper, more detailed), more vivid color, faces the text, etc. The caption could read "BEA Comet 4B arriving at Berlin Tempelhof Airport in 1969". Of course, the other photo has historical significance as well and probably should be retained in the article body, should this image be used. Interested in hearing any thoughts. Regards, SynergyStar (talk) 00:15, 5 January 2012 (UTC)[reply]
Thanks to everyone's efforts for making the Comet article much improved; this talk section is being added to complement the ongoing improvement efforts, as the article is at A-Class review (discussed at WP:MILHIST and mentioned at WP:AIRCRAFT). Having just gone through and done some copy-editing and formatting, it looks promising. Just some possible suggestions to ponder:
Check whether the testing info in "Design/Fuselage and testing process" might be better moved to the "Development/Testing and prototypes" section
Check whether italics should be used for quotations.
Thanks for the link, hopefully there will be more activity; I assume that MilbourneOne can continue to perform the administrative action on ACRs as previously? Regards SynergyStar (talk) 21:00, 5 March 2012 (UTC)[reply]
The recent changes to the specifications, which are now vaugly refeerenced to a large list of references rather than precisely cited means that no-one can tell where the information has comne from - please change back to a format with precise citeing.Nigel Ish (talk) 22:13, 1 May 2012 (UTC)[reply]
The individual spec data are now cited on a per figure basis, including the previous Comet 4-only specs (which had Jane's All The World's Aircraft 1965–66 as the main source). Individual cites now include Flight refs covering Comets A) 1,2,3, B) 3, and C) 4. Some references in this article differ on pax numbers though. Regards, SynergyStar (talk) 22:45, 1 May 2012 (UTC)[reply]
Hi all, thanks to everyone who contributed in the just-completed successful A-class review of this article. It was great that the article went through detailed discussion, which benefits its chances at FAC. I would like to open this discussion to discuss how people feel about the article going to FAC. Perhaps some additional polishing can be done, etc. Regards, SynergyStar (talk) 19:33, 7 May 2012 (UTC)[reply]
I'd be fine with the article being listed as a FAC in the near future; I've never been successful there however. Kyteto (talk) 10:36, 8 May 2012 (UTC)[reply]
As someone who's been involved with this article as a reviewer since GA (and before that as the editor who first added info and quotes from Macarthur Job and Nicholas Faith!) I've always treated it as a potential FAC. Because of that I've been quite tough on it in reviews, pushing for every scrap of data being fully cited, images being properly licensed, prose being of a high standard, and sources being used accurately but without copying or close paraphrasing. That doesn't mean I'd expect it to pass through FAC without incident, but speaking as an experienced FA editor/reviewer (and not as a FAC delegate) I think I'd nominate it sooner rather than later, without major changes, and keep the impetus going from its intensive but ultimately successful ACR. FWIW.. Cheers, Ian Rose (talk) 11:24, 8 May 2012 (UTC)[reply]
I too have been editing this article with an eye towards FAC, where I've had success in the past (most recently with Boeing 767). From examining this article, I believe that it is approaching FAC status, and agree that it would be prudent to nominate it in the near future to capitalise on its peak quality state. However, there would need to be active involvement among the major contributors to the article (access to references, verifying information, etc.) to provide timely responses to the suggestions of reviewers. Using past airliner/aircraft article FACs as a guide, we can also resolve potential issues before nominating—if fellow editors have the time to contribute. Regards, SynergyStar (talk) 20:18, 8 May 2012 (UTC)[reply]
I've try to develop all my articles to be compliant with the standards laid down by FAC, I don't believe that article content should be sloppy simply because "it isn't aiming to be a FAC"; the article was developed heavily in line with the conventions and layout dicated by the WP:Aircraft project and has grown to what I believe is a flush and wholesome extent. I've made some last minute tweaks inline with later A-class review comments regarding the Legacy section; I have no more deliberate plans to impliment at this point. I am prepared to be active as a main contributor throughout this article's nomination; if it is asked of me, I am happy to nominate this article as a FAC. I shall await responses and opinions prior to proceeding however, editors should be given the chance to impliment their own visions of improvements before proceeding with the nomination. I'll be watching this discussion closely. Kyteto (talk) 14:09, 9 May 2012 (UTC)[reply]
It is quite commendable to have high standards on all articles regardless of FAC plans. The WP:Aircraft guidelines are very useful, but one must keep in mind that MoS compliance is a FA requirement, while project guidelines are not binding there; it is the MoS that is the standard by which the article will be judged (some instances, such as the "see also" debate, pit the MoS against the WP:Aircraft guidelines, and it's pretty clear which has more solid support at FAC). Moreover, at FAC it is always a gamble as to what issues may crop up, what unforeseen difficulties or challenges may occur.
Now, the article has benefited tremendously from the A-class review. User:Ian Rose (a FAC delegate) correctly was tough during the review, as it increases the chances of its passing FAC. In the same vein, I feel that it is best to polish the article as much as possible before nominating it (if you are willing). To this end, there are a number of small fixes and further tweaks that this article probably needs, in part due to the varied and complex nature of its sections, and its comprehensiveness. This may seem like nitpicking, but I've seen multiple issues come up at FAC, and would prefer to head them off before nominating. It would be best if fellow collaborators work together to achieve this. Regards, SynergyStar (talk) 21:07, 9 May 2012 (UTC)[reply]
Alright, please bear with these suggestions as they're based on what reviewers have mentioned in past FACs; I'm adding a subheading to make it easier to access. One early item (lead citations should be moved into the body), I've done for one of the two references there. The accidents and incidents section has now been converted to summary style prose; one incident was removed (16 July 1953, BOAC Comet landed at Juhu Aerodrome instead of Santacruz Airport, Bombay, and was flown out some eight days later.[2][3]). The "Legacy" section has been moved below (after "Aircraft on display" and before "Specifications"), the reasoning being that discussion of legacies comes at the end, given that it is chronologically after the aircraft's complete history, variants, operators, etc. has been enumerated.
Completed tasks
Split the Operators section to List of de Havilland Comet operators, similar to List of De Havilland Heron operators, and leave a summary style prose section in its place. This reduces the amount of lists in the article (prose is generally preferred), and aligns the article with most other aircraft articles, where the operator list is on a separate page.
Remove common word wikilink ( "American operator Capital Airlines" - the first link is unnecessary).
The "operational history" and "aircraft on display" sections do not italicise registrations (e.g. G-ANLO) while the incidents section did (e.g. G-ALYZ); I have now corrected this.
Preparatory tasks
MoS, Formatting tasks
MOS:ITALICS: need to verify correct use of italics.
WP:MOSLINK: wikilinks not repeated throughout the text.
all citations follow a consistent format (order, details)
all necessary information is given (page numbers, full names, dates, etc.).
WP:ALT: alt text for images can benefit accessibility.
Reference tasks
Need access to most reference materials, in case material is challenged, requires clarification or further detail, or reviewers request source material for verification (not usually the case beyond spotchecks, usually online, but on rare occasion passage excerpts are asked).
Verify that citations indeed match the written material. User: Ian Rose has the Job (1996) and Faith (1996) books and did spotchecks; the article relies heavily on Darling (2001), which is available to me, and others, which may need to be verified (at least have access to them). Do we know which references User:Bzuk has access to?
User:Nikkimaria usually judges the citation formatting during FAC, and if asked may be able to do a preliminary review beforehand. The sheer volume of refs in this article is great, which is helpful but requires care.
These tweaks may seem a bit painstaking, but in my experience they will help ease the FAC process. Hopefully the article will continue to improve towards that goal! Regards, SynergyStar (talk) 02:05, 29 May 2012 (UTC)[reply]
The first bullet point at WP:MOS says that titles are in "sentence case". The exception of "eBay" is mentioned, but that's not really an exception, because eBay is actually lowercased even when publishers and journalists put it at the start of a sentence (which they avoid when possible), along with iPad, bell hooks, and k.d. lang. Each of these "brand names" is intended to look odd, to draw attention to itself, and it's been a constant fight for those few companies and individuals that have won a mention for their exceptional lowercasing in style guides. It doesn't appear to me that the same is true for this company; books I'm seeing are The De Havilland Dragon Rapide Family, De Havilland Aircraft since 1909, De Havilland: A Pictorial Tribute, and The De Havilland Canada Story. It's fine of course to lowercase the "de" throughout this article, since it never appears at the start of a sentence.
"the world's first production commercial jet airliner": slightly jargony for the first sentence. "the world's first commercial jet airliner in production". I guess "production" is fine the way you use it (adjectivally) after the first mention.
"landmark", "extremely", "exceptionally", "major success" ... too much for the first paragraph. Tone it down.
"... Comet airframes began suffering catastrophic metal fatigue, which in combination with cabin pressurisation cycles, caused two well-publicised accidents where the aircraft tore apart in mid-flight.": This is the one-sentence version of burying the lead ... that is, all aircraft have cabin pressurisation cycles; not all aircraft tear apart in mid-flight, and that's the part that you want to get to sooner rather than later. I'd go with: "... Comet airframes began suffering catastrophic metal fatigue; two of them tore apart in mid-flight in well-publicised accidents."
"Several contributory factors, such as window shape and installation methodology, were ultimately identified as exacerbating the problem. The Comet was extensively redesigned to eliminate this design flaw, with changes ...": Design flaws including window shape and installation methodology were ultimately identified, and the Comet was extensively redesigned, with changes ...
"a long and productive career of over 30 years": a productive career of over 30 years
"such as surveillance, VIP, medical and passenger transport": nonparallel. "such as surveillance and VIP, medical and passenger transport"
All that was in the lead, so the ride at FAC may be a little bumpy ... tighten your seatbelts and give it a once-over. It's already been through PR and A-class; I don't see a reason to hold off on FAC. - Dank (push to talk) 03:22, 29 May 2012 (UTC)[reply]
Thanks for the comments! Yes it seems that progress, and at least partial consensus, has helped the See also issue, which is now implemented both here and Boeing 757, both pending articles for review. Interesting about the capitalization issue for "de Havilland" as well.
Regarding the lead, I've simplified the first sentence to "first production commercial jetliner," which has the same meaning. The other suggestions have also been implemented. As for tone, I alluded to potential NPOV issues in my ACR comments, and have adjusted the ones in the lead.
As a more recent contributor to this article, I have considered whether to ask for a full copy-edit at the GoCE, but noticed that there is a significant backlog there. After some final polishing here and there, it may be ready for FAC, but I still want to smooth over the above issues (and several others) first if possible. Regards, SynergyStar (talk) 07:13, 29 May 2012 (UTC)[reply]
Just finished with a section-by-section formatting and integration process; in my opinion, the article could use some additional polishing, particularly with regards to consistency (everything--units to captions to references to wording to redundancy to details). This would address the comprehensiveness requirement, and go towards allaying any concerns over logical structure and the overall article quality. Some additional finessing of the prose would also better enable this article to approach the brilliant classification. Regards, SynergyStar (talk) 09:35, 31 May 2012 (UTC)[reply]
Continuing. I've got questions about this edit from last night. Either the de Havilland was the only aircraft among its competitors that could fly at all above 30,000 ft, or it was more fuel efficient at that altitude ... which was it? Also, there's a spelling error. Also, a hidden note was added saying there's no reference for the quieter operation, but the quieter operation was mentioned and referenced in the last paragraph of Overview. I don't see the reason for "all counting as advantages of Comets over their competitors"; isn't that clear? - Dank (push to talk) 12:00, 6 June 2012 (UTC)[reply]
Check for reliable source alternatives to Flickr and YouTube refs
Check geocities reference for actual author (can that be found?).
Quote: "front 16 seats were De Luxe: £17/17/- or $50 extra fare"--citation?
Alt text
Hello there; I don't know for sure who's list this is, but does any of it still need doing? I can address some of it now that my work is less overwhelmingly busy. Kyteto (talk) 08:47, 27 June 2012 (UTC)[reply]
Greetings, I added the list and somehow it was signed above. Anyhow, the first three are general MoS requirements which will be scrutinized at FAC. The last four though are more specific, and if someone could handle those it would be great. Reviewers may not like using Flickr, YouTube, or Geocities as references, the "De Luxe" quote could be cited, and alt text would appear more comprehensive as the FAC page toolbox automatically lists it as the first item. Regards, SynergyStar (talk) 21:57, 27 June 2012 (UTC)[reply]
Is it really true that CAA had a Comet leased from BOAC? I couldn't find any reference, neither concerning a Comet in CAA's fleet, nor it being announced as equipment in any CAA timetables (presumably on the Salisbury-London route). This article gives "Darling 2005, p. 119" as a source. Could someone with a deeper insight please check? --FoxyOrange (talk) 17:53, 12 January 2013 (UTC)[reply]
I don't have the Flight article link ATM but some of you may be interested in the intended replacement for the Comet. It was, guess what ..... what became Concorde. Concorde was actually designed as a Comet replacement - both BOAC and Air France had been early users of the Comet. — Preceding unsigned comment added by 80.7.147.13 (talk) 17:50, 3 May 2013 (UTC)[reply]
Sabotage of Comets Yoke Peter and Yoke Yoke by the DVD
The article as it currently appears contains major factual inaccuracies and recycles old myths, such as the myth that the Comet 1 had square windows. They in fact had rounded corners to reduce stress build-up. They were also tested by De Havillands to over 100 psi. There is no way that they would have failed in almost brand-new aircraft, nor is there any evidence that they did fail. RAE's report asserts that the break-up sequence commenced at the ADF panel, which was on the cabin ceiling, so why is the article talking about windows? The wreckage of Yoke Yoke was never recovered, and the crash of the Calcutta Comet was blamed on stabiliser failure - nothing to do with windows.
The article before my minor revisions (it needs major re-drafting) blamed all three losses on the windows, without any supporting evidence save that the Yoke Uncle test fuselage was eventually made to fail at the windows, having first failed at a wing. Put shortly the Yoke Uncle test failed to replicate the alleged break-up sequence of Yoke Peter and contradicted the window theory by suggesting that the wings would fail first, as we would expect, as they suffered greater cyclical stress.
The article is also out of date and fails to mention the latest research. I cannot help the fact that I published it. Instead of blaming me for self-promotion, blame the existing authors for failing to keep themselves up to date, with respect, on the literature on the Comet. The RAE theory is fatally flawed. Metal fatigue as an explanation for the losses of the Comets is a non-starter and they theory rests on skewed data. Michael Shrimpton (talk) 15:14, 19 September 2016 (UTC)[reply]
The OP is correct in that the Comet I's windows are often described as being 'square' when they did in fact have rounded corners, however the corner radius used was subsequently found to be insufficient and on later airliners a greater radius is used.
After the accident to YP there was no wreckage available as the aircraft came down into the sea, as a result the investigators were initially forced to theorise on the cause, which they concluded could be: (in order of likelihood)
1 Turbine disintegration.
2 Bomb.
3 Metal fatigue.
The last was discounted as the aircraft was too young seemingly for fatigue to be a factor.
Churchill ordered the wreckage to be recovered from the sea (the first time this had been attempted) and over the next year more of the wreckage became available to investigators, however in the mean time steps were taken by de Havilland's to armour the region of the wing likely to be damaged by a turbine disc failure. There was no evidence of foul play, so a bomb was also discounted. In the absence of contrary evidence and with the seemingly likely cause of the accident fixed - the turbine disc failure - flights were resumed by BOAC. Then the accident occurred to YY, and the Comet fleet were grounded indefinitely. Subsequently more wreckage was recovered from YP and it then became obvious to the AIB investigators that the cabin had suffered from an explosive decompression, which subsequent RAE tank tests with the Comet donated by BOAC confirmed, as well as revealing the cause - fatigue. They knew the cause of the two accidents was fatigue simply because the tank test cabin failed at several locations (the failures being repaired each time to allow the test to continue) at a ridiculously low number of pressurisation cycles. Design and pre-certification pressure tests of the Comet cabin had been carried out on a section of the cabin rather than on a whole cabin. This skewed the test results.
The wing failures were due to the detachment of the rear fuselage following the cabin failure leading to an abrupt pitch-down of the remainder of the aircraft which caused the outer wing sections to fail in overload. This pitch-down also caused extreme g forces which caused the engine compressor and turbine blades to contract their surrounding shrouds leaving tell-tale evidence of this process when the engines were recovered and examined.
The Calcutta accident was almost certainly caused by what is now known as wind-shear or clear air turbulence as the aircraft had just flown through a thunderstorm. The CP accident was caused by the pilot over-rotating on take-off and stalling the aircraft on the runway. The Comet design had been successfully flying for three years previously without anyone managing to do this. The accident was probably caused by the accident pilot's unfamiliarity with a swept wing.
BTW, if metal fatigue had not been the cause de Havilland's would not have 'wasted' a number of years on the Comet's re-design, nor on restricting existing Comet I's to flying un-pressurised, or in rather expensively scrapping them. — Preceding unsigned comment added by 95.150.11.183 (talk) 13:20, 28 June 2017 (UTC)[reply]
.svg)
The current image
Suggestion
