Single-ended primary-inductor converter: Difference between revisions

Content deleted Content added

Inline

Revision as of 21:16, 6 October 2006

A SEPIC (single ended primary inductor converter) is a DC-DC converter which allows the output voltage to be greater than, less than, or equal to the input voltage. The output voltage of the SEPIC is controlled by the duty cycle of the control transistor. The largest advantage of a SEPIC over the buck-boost converter is a non-inverted output (positive voltage).

Circuit Operation

Continuous Mode

The basic schematic for a SEPIC is shown in Figure 1. A SEPIC is said to be in continuous mode if the current through the inductor L1 never falls to zero. In a SEPIC, during steady-state operation, the average of V_C1 is V_in. Since C1 blocks DC current, the average of I_C1 is zero. Since I_C1 is zero, the only source of the average load current is I_L2. Therefore, the average current through L2 is the same as the load current and is independent of the input voltage.

Looking at average voltages, the following can be written:

$V_{IN}=V_{L1}+V_{C1}+V_{L2}$

and since the average voltage of V_C1 is equal to V_IN, V_L1 = -V_L2. For this reason, the two inductors can be wound on the same core. Since the voltages are the same in magnitude, their effects of the mutual inductance will be zero, assuming the polarity of the windings is correct. Also, since the voltages are the same in magnitude, the average currents from the two inductors will be equal in magnitude.

The average currents can be summed as follows:

$I_{D1}=I_{L1}-I_{L2}$

and since I_L1 = -I_L2, I_D1 = 2I_L1 = -2I_L2

When switch S1 is turned on, current I_L1 increases and the current I_L2 decreases (becomes more negative). The energy to increase the current I_L1 comes from the input source. Since S1 is a short while closed, and the instantaneous voltage V_C1 is approximately V_IN, the voltage V_L2 is approximately -V_IN. Therefore, the capacitor C1 supplies the energy to decrease (more negative) the current I_L2.

When switch S1 is turned off, the current I_L1 becomes the same as the current I_C1. Also, since inductors do not allow instantaneous changes in current, the current I_L2 will continue in the negative direction. From Kirchoff's Current Law, it can be shown that I_D1 = I_C1 - I_L2. It can then be concluded, that while S1 is off, power is delivered to the load from L2 and L1. C1, however is being charged by L1 during this off cycle, and will in turn recharge L1 during the on cycle.

The capacitor C_IN is required to reduce the effects of the parasitic inductance and internal resistance of the power supply. The boost/buck capabilities of the SEPIC are possible because of capacitor C1 and inductor L2. Inductor L1 and switch S1 create a standard boost converter, which generate a voltage (V_S1) that is higher than V_IN, whose magnitude is determined by the duty cycle of the switch S1. Since the average voltage across C1 is V_IN, the output voltage (V_O) is V_S1 - V_IN. If V_S1 is less than double V_IN, then the output voltage will be less than the input voltage. If V_S1 is greater than double V_IN, then the output voltage will be greater than the input voltage.

Discountinuous Mode

Non-Ideal Circuit

The voltage drop and switching time of the diode(D1) is extremely critical. The switching time needs to be extremely fast in order to not generate extremely high voltages across the inductors which could cause damage to components. Since not damaging components is more important than efficiency, a high speed silicon diode is normally used instead of Schottky diodes. The resistances in the inductors and the capacitors can also have large effects on the converter efficiency and ripple. Lower series resistance in the inductors allows for less energy dissipated as heat, which results in a large portion of the energy being transferred to the load. Low ESR capacitors should also be used for C1 and C2 to minimize ripple and prevent heat build up, especially in C1 where the current is changing direction frequently.

External Links

Excellent Design Guidelines from National Semiconductor in Application Note 1484

References

Maniktala,Sanjaya. Switching Power Supply Design & Optimization, McGraw-Hill, New York 2005

SEPIC Equations and Component Ratings, Maxim Integrated Products. Appnote 1051, 2005.

@@ Line 1: / Line 1: @@
 A '''SEPIC''' (single ended primary inductor converter) is a [[DC to DC converter|DC-DC converter]] which allows the output voltage to be greater than, less than, or equal to the input voltage. The output voltage of the SEPIC is controlled by the duty cycle of the control transistor.  The largest advantage of a SEPIC over the [[buck-boost converter]] is a non-inverted output (positive voltage).
 [[Image:SEPIC_Schematic.gif|thumb|500px|right|Figure 1: Schematic of SEPIC]]
-== Cicuit Operation ==
+== Circuit Operation ==
 === Continuous Mode ===
 The basic schematic for a SEPIC is shown in Figure 1. A SEPIC is said to be in continuous mode if the current through the inductor L1 never falls to zero.  In a SEPIC, during steady-state operation, the average of V<sub>C1</sub> is V<sub>in</sub>. Since C1 blocks DC current, the average of I<sub>C1</sub> is zero. Since I<sub>C1</sub> is zero, the only source of the average load current is I<sub>L2</sub>. Therefore, the average current through L2 is the same as the load current and is independent of the input voltage.