United States Standard thread: Difference between revisions
The abreviations UNC and UNF DO NOT mean Unified National Coarse or Fine. The unified thread standards was established to do away "national" threads. It established a "Unified" thread standard for the U.S. , Canada, and the U.K. |
|||
| Line 4: | Line 4: | ||
==Thread form== |
==Thread form== |
||
The thread form is defined by flats at the tip and root of the thread form. This flat length is defined as the pitch divided by eight. The thread depth, which is from flat to flat is 0.6495 times the pitch.<ref>{{Cite book | last = American Railway Master Mechanics' Association | title = Report of proceedings of the annual convention of the American Railway Master Mechanics' Association | publisher = American Railway Master Mechanics' Association | volume = 49 | year = 1916 | page = 71 | url = https://books.google.com/books?id=YKYR9N5cbUQC&pg=PA71}}</ref> For {{ |
The thread form is defined by flats at the tip and root of the thread form. This flat length is defined as the pitch divided by eight. The thread depth, which is from flat to flat is 0.6495 times the pitch.<ref>{{Cite book | last = American Railway Master Mechanics' Association | title = Report of proceedings of the annual convention of the American Railway Master Mechanics' Association | publisher = American Railway Master Mechanics' Association | volume = 49 | year = 1916 | page = 71 | url = https://books.google.com/books?id=YKYR9N5cbUQC&pg=PA71}}</ref> For {{convert|1/4|in|adj=on}} screws and larger, the pitch is defined as: |
||
:<math>P = 0.24 \sqrt {D + 0.625} - 0.175</math> |
:<math>P = 0.24 \sqrt {D + 0.625} - 0.175</math> |
||
where P is the pitch and D is the diameter of the rough stock.<ref name="adt"/> |
where ''P'' is the pitch and ''D'' is the diameter of the rough stock.<ref name="adt"/> |
||
==History and use== |
==History and use== |
||
Revision as of 23:06, 24 May 2018
United States Standard thread (USS thread), also known as Sellers Standard thread,[1] Franklin Institute thread[1] and American Standard thread,[2] is a standard for inch based threaded fasteners and washers.
The USS standard is no longer supported. It, together with the SAE fastener standard, was incorporated into the Unified Thread Standard. However, the term, USS, continues to be used occasionally today to describe inch based threaded fasteners with a coarse thread pitch and inch based washers that are a little bit larger than the corresponding SAE washer. The Unified Thread Standard uses the term UNC (Unified Coarse) to describe a fastener that previously would have been designated USS and the Unified Thread Standard uses the term UNF (Unified Fine) to describe a fastener that would have previously been designated SAE.
Thread form
The thread form is defined by flats at the tip and root of the thread form. This flat length is defined as the pitch divided by eight. The thread depth, which is from flat to flat is 0.6495 times the pitch.[3] For 1⁄4-inch (6.4 mm) screws and larger, the pitch is defined as:
where P is the pitch and D is the diameter of the rough stock.[1]
History and use
William Sellers originally developed the USS thread, and set forth many of its details in his paper, "A System of Screw Threads and Nuts", presented in April 1864 to the Franklin Institute. In 1898, the standard for metric threaded fasteners was established.[4] The metric standard used the same thread geometry as the USS standard but differed in that the dimensions and pitch were based on metric units. In 1906, the A.L.A.M developed what would be the SAE thread standard for threaded fasteners based on the USS standard but with a finer thread pitch.[5][6]
A Unified Thread Standard UNC thread is mechanically interchangeable with a USS thread of the same diameter. However, there are tolerance and other differences between a thread compliant with the USS thread and a Unified Thread Standard UNC thread.[7] The Unified Thread Standard for quarter inch and larger threaded fasteners was adopted on November 18, 1948,[8] and was subsequently adopted for smaller thread series.
See also
References
- ^ a b c Adt, Howard. Screw Thread Production to Close Limits. p. 7. Retrieved 2009-01-16.
- ^ "History of screw threads". Retrieved 2011-04-24.
- ^ American Railway Master Mechanics' Association (1916). Report of proceedings of the annual convention of the American Railway Master Mechanics' Association. Vol. 49. American Railway Master Mechanics' Association. p. 71.
- ^ Oberg, Erik; Jones, Franklin D.; McCauley, Christopher J.; Heald, Ricardo M. (2004), Machinery's Handbook (27th ed.), Industrial Press, p. 1726, ISBN 978-0-8311-2700-8.
- ^ The Society of Automobile Engineers 1912 Transactions Part II, pages 43-44. Retrieved 2009-01-17.
- ^ Browning's Industrial Magazine, page 590. The Browning Press. Retrieved 2009-01-27.
- ^ Oberg (1988). Machinery's Handbook 23rd edition. p. 1479.
- ^ National Bureau of Standards. "Screw-Thread Standards for Federal Services, pages 10-12" (PDF). Retrieved 2009-01-16.