Bootleg ground: Difference between revisions
PetesGuide (talk | contribs) Added text to clarify the content is specific to one type of electrical distribution network used in the U.S.--the most common residential wiring scheme. |
PetesGuide (talk | contribs) Separated mention of Germany into new section. |
||
| Line 6: | Line 6: | ||
== Introduction == |
== Introduction == |
||
In United States [[building wiring]] installed according to the [[Earthing system#Types of TN networks|TN-S network]], a '''bootleg ground''' (or a false ground) is an electrical [[Ground (electricity)|ground]] that is wired from the neutral side of a [[AC power plugs and sockets|receptacle]] or light fixture in an older 2-wire home.<ref>Steven Bliss ''Troubleshooting Guide to Residential Construction ''Craftsman Book Company, 1997 {{ISBN|1-928580-23-8}}, page 287</ref> This essentially connects the neutral side of the receptacle to the casing of an appliance or lamp. It can be a hazard because the neutral wire is a current-carrying conductor, which means the casing can become energized.<ref name=":0">{{Cite journal|last=Sokol|first=Mike|date=2013|title=Failures in Outlet Testing Exposed|url=https://www.ecmweb.com/contractor/failures-outlet-testing-exposed|journal=Electrical Construction & Maintenance magazine|volume=|pages=|via=}}</ref> In addition, a fault condition to a bootleg ground will not trip a [[Residual-current device|GFCI]] breaker or a receptacle that is wired from the load side of a GFCI receptacle. Bootleg grounding is now against [[Electrical code|code]] in many places, but was once common in some places |
In United States [[building wiring]] installed according to the [[Earthing system#Types of TN networks|TN-S network]], a '''bootleg ground''' (or a false ground) is an electrical [[Ground (electricity)|ground]] that is wired from the neutral side of a [[AC power plugs and sockets|receptacle]] or light fixture in an older 2-wire home.<ref>Steven Bliss ''Troubleshooting Guide to Residential Construction ''Craftsman Book Company, 1997 {{ISBN|1-928580-23-8}}, page 287</ref> This essentially connects the neutral side of the receptacle to the casing of an appliance or lamp. It can be a hazard because the neutral wire is a current-carrying conductor, which means the casing can become energized.<ref name=":0">{{Cite journal|last=Sokol|first=Mike|date=2013|title=Failures in Outlet Testing Exposed|url=https://www.ecmweb.com/contractor/failures-outlet-testing-exposed|journal=Electrical Construction & Maintenance magazine|volume=|pages=|via=}}</ref> In addition, a fault condition to a bootleg ground will not trip a [[Residual-current device|GFCI]] breaker or a receptacle that is wired from the load side of a GFCI receptacle. Bootleg grounding is now against [[Electrical code|code]] in many places, but was once common in some places. A safer alternative, allowed in recent editions of the [[National Electrical Code]] [NEC Sec. 406.4(D)(2)(b)] if a grounding connection is not practicable (where a local electrical code allows it) is to install a [[Residual-current device|GFCI]] and leave the grounding terminal screw unconnected, then place a label that says "No Equipment Ground" on the GFCI and a marking that states “GFCI Protected” and “No Equipment Ground” on all downstream receptacles. |
||
=== Correct-polarity bootleg ground === |
=== Correct-polarity bootleg ground === |
||
| Line 16: | Line 16: | ||
==120/240 volt split-phase circuits== |
==120/240 volt split-phase circuits== |
||
Before 1996, in the United States it was common to ground the frames of 120/240-volt appliances (such as a [[clothes dryer]] or [[oven]]) to neutral (grounded) conductors. This has been prohibited in new installations since the 1996 National Electrical Code upon local adoption by legislation or regulation. Existing installations are permitted to continue in accordance with NEC 250.140 Exception. |
Before 1996, in the United States it was common to ground the frames of 120/240-volt appliances (such as a [[clothes dryer]] or [[oven]]) to neutral (grounded) conductors. This has been prohibited in new installations since the 1996 National Electrical Code upon local adoption by legislation or regulation. Existing installations are permitted to continue in accordance with NEC 250.140 Exception. |
||
==Other countries== |
|||
West Germany banned bootleg grounding in 1973, although it was common practice before and can still be found in older installations. |
|||
==See also== |
==See also== |
||
Revision as of 22:36, 19 November 2018
 | This article needs attention from an expert on the subject. The specific problem is: Is there any difference between this and TN-S? The article does not make it clear for European readers. (January 2015) |
Introduction
In United States building wiring installed according to the TN-S network, a bootleg ground (or a false ground) is an electrical ground that is wired from the neutral side of a receptacle or light fixture in an older 2-wire home.[1] This essentially connects the neutral side of the receptacle to the casing of an appliance or lamp. It can be a hazard because the neutral wire is a current-carrying conductor, which means the casing can become energized.[2] In addition, a fault condition to a bootleg ground will not trip a GFCI breaker or a receptacle that is wired from the load side of a GFCI receptacle. Bootleg grounding is now against code in many places, but was once common in some places. A safer alternative, allowed in recent editions of the National Electrical Code [NEC Sec. 406.4(D)(2)(b)] if a grounding connection is not practicable (where a local electrical code allows it) is to install a GFCI and leave the grounding terminal screw unconnected, then place a label that says "No Equipment Ground" on the GFCI and a marking that states “GFCI Protected” and “No Equipment Ground” on all downstream receptacles.
Correct-polarity bootleg ground
In the least-dangerous instance of a bootleg ground, a short wire jumper is connected between the bonding screw terminal (usually colored green) on a NEMA 5-15R or 5-20R outlet to the neutral (a.k.a. non-grounded conductor, colored white according to code) or directly to the white neutral wire via a pigtail. This practice is a NEC code violation, but a standard 3-lamp receptacle tester will report the outlet as correctly wired.[2]
Reverse-polarity bootleg ground
In the very-dangerous instance of a bootleg ground, the hot and neutral wires have been connected to the opposite terminals, and a jumper or pigtail connection is made between the green bonding screw terminal and what is believed to be the neutral circuit. But because the wiring has been crossed at some point, the hot 120 Volt wire is now connected directly to the ground on the receptacle, placing live voltage on all grounded parts of all equipment plugged into that outlet, thus allowing people to come into contact with a deadly voltage that can travel back to the source[2] (the power transformer) through a path that does not trip either a normal circuit breaker, a GFCI, nor an AFCI soon enough to prevent electrocution.
120/240 volt split-phase circuits
Before 1996, in the United States it was common to ground the frames of 120/240-volt appliances (such as a clothes dryer or oven) to neutral (grounded) conductors. This has been prohibited in new installations since the 1996 National Electrical Code upon local adoption by legislation or regulation. Existing installations are permitted to continue in accordance with NEC 250.140 Exception.
Other countries
West Germany banned bootleg grounding in 1973, although it was common practice before and can still be found in older installations.
See also
References
- ^ Steven Bliss Troubleshooting Guide to Residential Construction Craftsman Book Company, 1997 ISBN 1-928580-23-8, page 287
- ^ a b c Sokol, Mike (2013). "Failures in Outlet Testing Exposed". Electrical Construction & Maintenance magazine.
 | This electricity-related article is a stub. You can help Wikipedia by expanding it. |