Jump to content

Aerojet M-1

From Wikipedia, the free encyclopedia

This is an old revision of this page, as edited by InternetArchiveBot (talk | contribs) at 06:28, 11 November 2017 (Rescuing 1 sources and tagging 0 as dead. #IABot (v1.6.1) (Balon Greyjoy)). The present address (URL) is a permanent link to this revision, which may differ significantly from the current revision.

M-1
M-1 rocket engine specifications
Country of originUnited States
First flightDevelopment abandoned at pre-prototype stage
ManufacturerAerojet
StatusAbandoned in development stage.
Liquid-fuel engine
PropellantLOX / Liquid hydrogen
Cyclegas-generator cycle
Performance
Thrust, vacuum1,500,000 lbf (6.67 MN)
Thrust-to-weight ratio60
Chamber pressure1,000 psia
Specific impulse, vacuum428 seconds (4.20 km/s)
Dimensions
Length7.72 m
Diameter4.28 m
Dry mass9068 kg

Aerojet's M-1 was the largest and most powerful liquid-hydrogen-fueled liquid-fuel rocket engine to be designed and component-tested. The M-1 offered a baseline thrust of 6.67 MN (1.5 million lbf) and 8 MN (1.8 million lbf) as its immediate growth target. If built, the M-1 would be larger and more efficient than the famed F-1 that powered the first stage of the Saturn V rocket to the Moon.

History

The M-1 traces its history to US Air Force studies from the late 1950s for its launch needs in the 1960s. By 1961 these had evolved into the Space Launcher System design. The SLS consisted of a series of four rocket designs, all built around a series of solid-fuel boosters and liquid-hydrogen-powered upper stages.

The smallest model, intended to launch the Dynasoar, used two 100-inch (2,500 mm) solids and an "A" liquid core. To power the "A" booster, Aerojet was contracted to convert an LR-87, used in the Titan II missile, to run on liquid hydrogen. A prototype was successfully tested between 1958 and 1960. Initial studies of the 100-inch (2,500 mm) solid were also handed to Aerojet, starting in 1959.

The SLS also envisioned a number of much larger designs intended to launch the Air Force's Lunex Project manned lunar landing. Lunex was a direct landing mission, in which a single very large spacecraft would fly to the Moon, land, and return. In order to launch such a design to low Earth orbit (LEO), a very large booster with a 125,000 lb (57,000 kg) payload would be required. These larger SLS designs followed the same basic outline as the smaller Dynasoar booster, but used much more powerful 180-inch (4,600 mm) solids and the "B" and "C" liquid stages. To provide the required power, the liquid stages mounted a cluster of twelve J-2s. To reduce this complexity, the Air Force also had Aerojet start studies of a much larger hydrogen-fueled design that would replace the twelve J-2s with only two engines. These initial studies would eventually emerge as the M-1, with a thrust of 1.2 million pounds force.

When NASA formed in 1958, they also started planning for a lunar landing. Like the Air Force, their Project Apollo initially favoured a direct landing profile, requiring a large booster to launch the spacecraft into LEO. Prior to NASA taking over Wernher von Braun's Saturn work for the US Army, they had no large rocket designs of their own, and started a study program known as Nova to study a range of options. Initially the payload requirements were fairly limited, and the favoured Nova designs used a first stage with four F-1 engines and a payload of about 50,000 lb (23,000 kg). These designs were presented to President Dwight D. Eisenhower on January 27, 1959.

However, the Apollo spacecraft requirements quickly grew, settling on a 10,000 lb (4,500 kg) spacecraft (the CSM) with a three-man crew. To launch a 10,000 lb (4,500 kg) craft to the Moon required a massive 125,000 lb (57,000 kg) payload to LEO. Nova designs of this capability were quickly presented with up to eight F-1 engines, along with much more powerful upper stages that demanded the M-1 engine. Thus, for a brief period, the M-1 was used on the baseline designs for both NASA's and the Air Force's lunar programs.

In 1961, President John F. Kennedy announced his intentions of landing a man on the Moon before the decade was out. After a brief argument, NASA won the mission over the Air Force. However, Nova would require massive manufacturing capability that did not currently exist, and it was not clear that booster construction could be started in time for a landing before 1970. By 1962 they had decided to use von Braun's Saturn design, which went through a process of re-design to produce a usable booster that could be built in the existing facilities at Michoud, Louisiana.

With the selection of Saturn for the lunar missions, work on Nova turned to the post-Apollo era. The designs were re-targeted for manned planetary expedition, namely a manned landing on Mars. Even utilizing a lightweight mission profile like that selected for Apollo, a Mars mission required a truly massive payload of about one million pounds to low Earth orbit. This led to a second series of design studies, also known as Nova, although they were essentially unrelated to the earlier designs.

Many of the new designs used the M-1 as their second-stage engine, although demanding much higher payloads. In order to meet these goals, the M-1 project was uprated from 1.2 million pounds force to a nominal 1.5 million pounds force, and the designers deliberately added more turbopump capability to allow it to expand to at least 1.8 million pounds force and potentially as high as 2.0 million pounds force.[1] Additionally, the M-1 was even considered for a number of first-stage designs, in place of the F-1 or the 180-inch (4,600 mm) solids. For this role the specific impulse was dramatically reduced, and it appears that some consideration was given to various expanding nozzle designs to address this.

M-1 development continued through this period, although as the Apollo program expanded, NASA started cutting funding to the M-1 project in order to complete Saturn-related developments first. In 1965, another NASA project studied advanced versions of the Saturn, replacing the cluster of five J-2s on the S-II second stage with one M-1, five J-2Ts (an improved version of the J-2 with an aerospike nozzle), or a high-pressure engine known as the HG-3, which would later become the direct predecessor of the Space Shuttle SSME.

By 1966 it was clear that present funding levels for NASA would not be maintained in the post-Apollo era. The Nova design studies ended that year, and the M-1 along with it. The last M-1 contract expired on August 24, 1965, although testing continued on existing funds until August 1966. Studies on the J-2T ended at the same time. Although the HG-3 was never built, its design formed the basis for the Space Shuttle Main Engine.

Description

The M-1 used the gas-generator cycle, burning some of its liquid hydrogen and oxygen in a small combustor to provide hot gases for running the fuel pumps. In the case of the M-1, the hydrogen and oxygen turbopumps were completely separate, each using their own turbine, rather than running both off a common power shaft. The hydrogen and oxygen pumps were some of the most powerful ever built at the time, producing 75,000 horsepower for the former, and 27,000 hp (20,000 kW) for the latter.

M-1 rocket engine display at Evergreen Aviation & Space Museum
A turbopump designed and built for the M-1 rocket engine

In most American designs, a gas-generator engine would dump the exhaust from the turbines overboard. In the case of the M-1, the resulting exhaust was relatively cool, and was instead directed into cooling pipes on the lower portion of the engine skirt. This meant that liquid hydrogen was needed for cooling only on the high-heat areas of the engine —the combustion chamber, nozzle and upper part of the skirt— reducing plumbing complexity considerably. The gas entered the skirt area at about 700 °F (371 °C), heating to about 1,000 °F (538 °C) before being dumped through a series of small nozzles at the end of the skirt. The exhaust added 28,000 lbf (120 kN) of thrust.

The engine was started by driving the pumps to speed by helium gas stored in a separate high-pressure container. This started the fuel flow into the main engine and gas generator. The main engine was ignited by a generator that sprayed sparks into the combustion area. Shutdown was achieved by simply turning off the fuel flow to the gas generator, allowing the pumps to slow down on their own.

The use of separate turbopumps and other components allowed the various parts of the M-1 to be built and tested individually. Over the three-year lifetime of the project, a total of eight combustion chambers were built (two of them uncooled test units), eleven gas generators, four oxygen pumps, as well as four hydrogen pumps that were in the process of being completed.

References

  1. ^ Dankhoff 1963, pp. 1–2.

Bibliography

Retrieved from "https://en.wikipedia.org/enwiki/w/index.php?title=Aerojet_M-1&oldid=809760813"