Experimental Model 2 submachine gun
Experimental Model 2 submachine gun | |
---|---|
Type | Submachine gun |
Place of origin | Empire of Japan |
Service history | |
In service | 1935–1945 (Japan) |
Used by | Imperial Japanese Army |
Wars | Second Sino-Japanese War World War II Chinese Civil War[1] |
Production history | |
Designer | Kijiro Nambu |
Designed | 1935 |
Manufacturer | Nambu |
No. built | 50-150 |
Variants | Mukden Type 2 |
Specifications | |
Mass | 3.37 kg (7 lb 7 oz) (empty) 4.39 kg (9 lb 11 oz) (loaded) |
Length | 896 mm (35 in) |
Barrel length | 228 mm (9 in) |
Cartridge | 8×22mm Nambu .45 ACP (Mukden Type 2) |
Caliber | 8 mm 11.5mm (Mukden Type 2) |
Action | Blowback |
Rate of fire | 800 rounds/min |
Feed system | 30 and 50 round box magazine[2] |
Sights | Iron sights |
The Experimental Model 2 submachine gun (試製二型機関短銃, Shisei-ni-gata kikan-tanjū) was a pre–World War II experimental submachine gun of Japanese origin chambered in the 8mm Nambu round.
History
The Type 2 was a development of the earlier Type 1 submachine gun, designed in response to criticisms of the Type 1's awkward ergonomics. The Type 2 offered a more conventional magazine feed and stock, but wholly retained the Type 1's method of operation and was essentially the same gun in a different body. It was initially produced in the mid-1930s and was tested by the Imperial Japanese Army, but rejected. During World War II, an urgent demand for automatic infantry weapons saw the revival of several experimental weapon projects, including the Type 2 submachine gun. Blueprints of the weapon was sent to the Mukden Arsenal in Manchukuo in 1944 for use in development of cheap submachine guns. Instead, those blueprints were used by the Chinese communists to produce submachine guns to be used in the Chinese Civil War following the end of the war with Japan and communist control over Mukden. These weapons were operationally identical but chambered in .45 ACP rather than 8×22mm Nambu.[1] The British and US armies studied examples of the earlier Japanese prototypes obtained in Singapore and Japan after the surrender of Japan.
Design details
The Type 2 was a blowback-operated submachine gun that fired from a closed bolt. Much like the Type 1, the Type 2's return spring enveloped the barrel of the gun rather than behind the bolt. The front section of the receiver and barrel shroud would travel back with the bolt upon firing and be pushed back forward by the return spring. The barrel stayed stationary. The cocking handle was not located in a slotted groove but instead took the form of a protruding tab fixed to the left side of the receiver. Early pre-war prototypes of the Type 2 were built with the same pneumatic buffer device seen on the Type 1, which cushioned the action of the gun and acted as a bolt delay. The timing of the delay could be adjusted by changing the air pressure exerted by the buffer, thus lowering or increasing the fire rate. This was done by turning a pressure valve located underneath the rear cap. The later wartime models omitted the air buffer feature in an attempt to cut the expensive production costs. The Type 2 typically issued with 30-round magazines, although it could also feed from the same 50-round magazines as the Type 1.[3] Late-war examples of the Type 2 had bayonet fittings, a feature not present on the original production models. A spike bayonet was also designed for the gun but was not used on the production models. The finish of the late-war models was typically poor compared to the earlier pre-war prototypes.
See also
- List of submachine guns
- List of common World War II infantry weapons
- List of Japanese military equipment of World War II
References
- ^ a b "Mukden Arsenal after WWII". 3 April 2017.
- ^ "Dragons of Fire". Archived from the original on 2020-10-07. Retrieved 2009-04-02.
- ^ Illustrated Directory of 20th Century Guns, David Miller, 2002
Further reading
- Chris Bishop et al. The Complete Encyclopedia of Weapons of World War II. Brown Books, 1998.