Little Boy

This article is about the type of atomic bomb that was dropped on Hiroshima. For other uses, see Little Boy (disambiguation).

Little Boy
A post-war Little Boy model
Type	Nuclear weapon
Place of origin	United States
Production history
Designer	Los Alamos Laboratory
Manufacturer	Naval Gun Factory, Washington, D.C. Naval Ordnance Plant, Center Line, Michigan Expert Tool and Die Company, Detroit, Michigan
Produced	1945–1947
No. built	1 wartime + 5 postwar
Specifications
Mass	9,700 pounds (4,400 kg)
Length	10 feet (3.0 m)
Diameter	28 inches (71 cm)
Filling	Highly enriched uranium
Filling weight	64 kg
Blast yield	15 kilotons of TNT (63 TJ)

Little Boy was the name of the type of atomic bomb used in the bombing of the Japanese city of Hiroshima on 6 August 1945 during World War II, making it the first nuclear weapon used in warfare. The bomb was dropped by the Boeing B-29 Superfortress Enola Gay piloted by Colonel Paul W. Tibbets Jr., commander of the 509th Composite Group, and Captain Robert A. Lewis. It exploded with an energy of approximately 15 kilotons of TNT (63 TJ) and had an explosion radius of approximately 1.3 kilometers which caused widespread death across the city. The Hiroshima bombing was the second nuclear explosion in history, after the Trinity nuclear test.

Little Boy was developed by Lieutenant Commander Francis Birch's group at the Manhattan Project's Los Alamos Laboratory during World War II, a reworking of their abandoned Thin Man nuclear bomb. Like Thin Man, it was a gun-type fission weapon. It derived its explosive power from the nuclear fission of uranium-235, whereas Thin Man was based on fission of plutonium-239. Fission was accomplished by shooting a hollow cylinder (the "bullet") onto a solid cylinder of the same material (the "target") by means of a charge of nitrocellulose propellant powder. Little Boy contained 64 kilograms (141 lb) of highly enriched uranium, although less than a kilogram underwent nuclear fission. Its components were fabricated at three different plants so that no one would have a copy of the complete design. Unlike the implosion design, which required sophisticated coordination of shaped explosive charges, the gun-type design was considered almost certain to work so it was never tested before its first use at Hiroshima.

After the war, a number of components for further Little Boy bombs were built. By 1950, only five complete weapons had been created, and these were retired by November 1950.

Naming

Robert Serber claims that the original gun-type design, Thin Man, was named after the series of noir films based on the work of Dashiell Hammett that were popular in the 1930s and 1940s. "Little Boy" was itself derived from the earlier design codenames of "Thin Man" and "Fat Man".

There are two primary accounts of how the first atomic bombs got their names.

Los Alamos and Project Alberta physicist Robert Serber claimed, many decades after the fact, to have named the first two atomic bomb designs during World War II based on their shapes: Thin Man and Fat Man. The "Thin Man" was a long, thin device and its name came from the Dashiell Hammett detective novel and series of movies about The Thin Man. The "Fat Man" was round and fat so it was named after Kasper Gutman, a rotund character in Hammett's 1930 novel The Maltese Falcon, played by Sydney Greenstreet in the 1941 film version. Little Boy was named by others as an allusion to Thin Man since it was based on its design.

In September 1945, another Project Alberta physicist, Norman F. Ramsey, claimed in his brief "History of Project A," that the early bomb ballistic test shapes designs were referred to as "Thin Man" and "Fat Man" by (unspecified) "Air Force representatives" for "security reasons," so that their communications over telephones sounded "as if they were modifying a plane to carry Roosevelt (the Thin Man) and Churchill (the Fat Man)," as opposed to modifying the B-29s to carry the two atomic bomb shapes as part of Project Silverplate in the fall of 1943.

Another explanation of the names, from a classified United States Air Force history of Project Silverplate from the 1950s, implies a possible reconciliation of the two versions above: that the terms "Thin Man" and "Fat Man" were first developed by someone at or from Los Alamos (i.e., Serber), but were consciously adopted by the officers in Silverplate when they were adopting their own codenames for their own project (including "Silverplate"). As Silverplate involved modifying B-29s for a secret purpose, deliberately using codenames that would align with modifying vehicles for Roosevelt and Churchill would serve their needs well.

Development

Main article: Manhattan Project

Early gun-type design work

Main article: Thin Man (nuclear bomb)

Different fission bomb assembly methods explored during the July 1942 conference. The gun-type design was the first described; third from the top is an early concept of implosion, while the last shows an autocatalytic concept in which the process of the reaction would increase its own efficiency.

Because of its perceived simplicity, the gun-type nuclear weapon design was the first approach pursued by the scientists working on bomb design during the Manhattan Project. In 1942, it was not yet known which of the two fissile materials pathways being simultaneously pursued — uranium-235 or plutonium-239 — would be successful, or if there were significant differences between the two fuels that would impact the design work. Coordination with British scientists in May 1942 convinced the American scientists, led by J. Robert Oppenheimer, that the atomic bomb would not be difficult to design, and that the difficulty would lie only in the production of fuel. Early calculations in the summer of 1942 by theoretical physicists working on the project reinforced the idea that an ordinary artillery gun barrel would be able to impart sufficient velocity to the fissile material projectile.

Several different weapon designs, including autocatalytic assembly, a nascent version of implosion, and alternative gun designs (e.g., using high explosives as a propellent, or creating a "double-gun" with two projectiles) were pursued in the early years of the project, while the facilities to manufacture fissile material were being constructed. The belief that the gun design would be an easy engineering task once fuel was available led to a sense of optimism at Los Alamos, although Oppenheimer established a small research group to study implosion as a fallback in early 1943. A full ordnance program for gun-design development was established by March 1943, with expertise provided by E.L. Rose, an experienced gun-designer and engineer. Work was begun to study the properties of barrels, internal and external ballistics, and tampers of gun weapons. Oppenheimer himself led aspects of the effort, telling Rose that "at the present time [May 1945] our estimates are so ill founded that I think it better for me to take responsibility for putting them forward." He soon delegated the work to Naval Captain William Sterling Parsons, who, along with Ed McMillan, Charles Critchfield, and Joseph Hirschfelder would be responsible for rendering the theory into practice.

"Thin Man" plutonium gun test casings at Wendover Army Air Field, as part of Project Alberta in the Manhattan Project, illustrating their relative length and size.

Concern that impurities in reactor-bred plutonium would make predetonation more likely meant that much of the gun-design work was focused on the plutonium gun. To achieve high projectile velocities, the plutonium gun was 17 feet (5.2 m) long with a narrow diameter — suggesting its code-name as the Thin Man — which created considerable difficulty in its ballistics dropping from aircraft and fitting it into the bomb bay of a B-29.

In the spring of 1944, Emilio G. Segrè and his P-5 Group at Los Alamos received the first samples of plutonium produced from a nuclear reactor, the X-10 Graphite Reactor at Oak Ridge. Analyzing it, they discovered that the presence of the isotope plutonium-240 raised the rate of spontaneous fission of the plutonium to an unacceptable amount. Previous analyses of plutonium had been made from samples created by cyclotrons, and did not have as much of the contaminating isotope. If reactor-bred plutonium were to be used in a gun-type design, they concluded, it would predetonate, causing the weapon to destroy itself before achieving the conditions for a large-scale explosion.

As part of Project Alberta, Commander A. Francis Birch (left) assembles the bomb while physicist Norman Ramsey watches. This is one of the rare photos where the inside of the bomb can be seen.

From Thin Man to Little Boy

As a consequence of the discovery of the Pu-240 contamination problem, in July 1944 almost all research at Los Alamos was redirected to the implosion-type plutonium weapon, and the laboratory itself was entirely reorganized around the implosion problem. Work on the gun-type weapon continued under Person's Ordnance (O) Division, for use exclusively with highly enriched uranium as a fuel. All the design, development, and technical work at Los Alamos was consolidated under Lieutenant Commander Francis Birch's group. In contrast to the plutonium implosion-type nuclear weapon and the plutonium gun-type fission weapon, the uranium gun-type weapon was much simpler to design. As a high-velocity gun was no longer required, the overall length of the gun barrel could be dramatically decreased, and this allowed the weapon to fit into a B-29 bomb bay without difficulty. Though not an optimal use of fissile material compared to the implosion design, it was seen as a nearly guaranteed weapon. Because of its smaller size compared to the Thin Man, it was given the code-name "Little Boy," while the plutonium implosion bomb was given the name "Fat Man." It was also sometimes referred to as the "Mark I" nuclear bomb design, with "Mark II" referring to the abandoned Thin Man, and "Mark III" to the "Fat Man."

The design specifications were completed in February 1945, and contracts were let to build the components. Three different plants were used so that no one would have a copy of the complete design. The gun and breech were made by the Naval Gun Factory in Washington, D.C.; the target case and some other components by the Naval Ordnance Plant in Center Line, Michigan; and the tail fairing and mounting brackets by the Expert Tool and Die Company in Detroit, Michigan. The bomb, except for the uranium payload, was ready at the beginning of May 1945. Manhattan District Engineer Kenneth Nichols expected on 1 May 1945 to have enriched uranium "for one weapon before August 1 and a second one sometime in December", assuming the second weapon would be a gun type; designing an implosion bomb for enriched uranium was considered, and this would increase the production rate. The enriched uranium projectile was completed on 15 June, and the target on 24 July. The target and bomb pre-assemblies (partly assembled bombs without the fissile components) left Hunters Point Naval Shipyard, California, on 16 July aboard the heavy cruiser USS Indianapolis, arriving on 26 July. The target inserts followed by air on 30 July.

Although all of its components had been individually tested, no full test of a gun-type nuclear weapon occurred before the Little Boy was dropped over Hiroshima. The only test explosion of a nuclear weapon concept had been of an implosion-type device employing plutonium as its fissile material, and took place on 16 July 1945 at the Trinity nuclear test. There were several reasons for not testing a Little Boy type of device. Primarily, there was the issue of fissile material. Oak Ridge was designed to produce around 30 kilograms of enriched uranium per month, and the Little Boy design used over 60 kilograms per bomb. So testing the weapon would incur a considerable delay in use of the weapon. (By comparison, the Hanford plant was designed to produce around 20 kilograms of plutonium per month, and each Fat Man bomb used only around 6 kilograms of material.) Because of the simplicity of the gun-type design, laboratory testing could establish that its parts worked correctly on their own — for example, dummy projectiles could be shot down the gun barrel to make sure they were "seated" correctly onto a dummy target. By comparison, with the implosion design it was much more difficult to establish absence of a full-scale test whether the necessary simultaneity of compression had been achieved. While there was at least one prominent scientist (Ernest O. Lawrence) who advocated for a full-scale test, by the spring of 1945 Little Boy was regarded as nearly a sure-thing, and was expected to have a higher-yield than the first-generation implosion bombs.

Though Little Boy incorporated various safety mechanisms, an accidental detonation of a fully-assembled weapon was very possible. For example, should the bomber carrying the device crash then the hollow "bullet" could be driven into the "target" cylinder, possibly detonating the bomb from gravity alone (though tests suggested this was unlikely), but easily creating a critical mass that would release dangerous amounts of radiation. And crash of the B-29 and subsequent fire could trigger the explosives, causing the weapon to detonate. If immersed in water, the uranium components were subject to a neutron moderator effect, which would not cause an explosion but would release radioactive contamination. For this reason, pilots were advised to crash on land rather than at sea. Ultimately, Parsons opted to keep the explosives out of the Little Boy bomb until after the B-29 had taken off, to avoid the risk of a crash that could destroy or damage the military base the weapon was being launched from.

Design

The "gun" assembly method. When the hollow uranium projectile was driven onto the target cylinder, a nuclear explosion resulted.

Two Little Boy type bomb assemblies on Tinian, with casings open. For unit L-1, in the foreground, boxes containing hardware for the clock timers, radar fuzing units, and batteries are visible and arranged around the central gun tube. Pull-out wires are visible on top. L-1 was test-dropped without nuclear fuel on July 23, 1945, to gain experience in assembling, handling, and using the weapons prior to the actual strike (which used unit L-11).

The Little Boy was 120 inches (300 cm) in length, 28 inches (71 cm) in diameter and weighed approximately 9,700 pounds (4,400 kg). The design used the gun method to explosively force a hollow sub-critical mass of enriched uranium and a solid target cylinder together into a super-critical mass, initiating a nuclear chain reaction. This was accomplished by shooting one piece of the uranium onto the other by means of four cylindrical silk bags of cordite powder. This was a widely used smokeless propellant consisting of a mixture of 65 percent nitrocellulose, 30 percent nitroglycerine, 3 percent petroleum jelly, and 2 percent carbamite that was extruded into tubular granules. This gave it a high surface area and a rapid burning area, and could attain pressures of up to 40,000 pounds per square inch (280,000 kPa). Cordite for the wartime Little Boy was sourced from Canada; propellant for post-war Little Boys was obtained from the Picatinny Arsenal. The bomb contained 64 kilograms (141 lb) of enriched uranium. Most was enriched to 89% but some was only 50% uranium-235, for an average enrichment of 80%. Less than a kilogram of uranium underwent nuclear fission, and of this mass only 0.7 grams (0.025 oz) was transformed into several forms of energy, mostly kinetic energy, but also heat and radiation.

Assembly details

Inside the weapon, the uranium-235 material was divided into two parts, following the gun principle: the "projectile" and the "target". The projectile was a hollow cylinder with 60% of the total mass (38.5 kilograms [85 lb]). It consisted of a stack of nine uranium rings, each 6.25 inches (159 mm) in diameter with a 4-inch (100 mm) bore in the center, and a total length of 7 inches (180 mm), pressed together into the front end of a thin-walled projectile 16.25 inches (413 mm) long. Filling in the remainder of the space behind these rings in the projectile was a tungsten carbide disc with a steel back. At ignition, the projectile slug was pushed 42 inches (1,100 mm) along the 72-inch-long (1,800 mm), 6.5-inch-wide (170 mm) smooth-bore gun barrel. The slug "insert" was a 4-inch cylinder, 7 inches in length with a 1-inch (25 mm) axial hole. The slug comprised 40% of the total fissile mass (25.6 kilograms or 56 pounds). The insert was a stack of six washer-like uranium discs somewhat thicker than the projectile rings that were slid over a 1-inch rod. This rod then extended forward through the tungsten carbide plug, impact-absorbing anvil, and nose plug backstop, eventually protruding out of the front of the bomb casing. This entire target assembly was secured at both ends with locknuts.

When the hollow-front projectile reached the target and slid over the target insert, the assembled super-critical mass of uranium would be completely surrounded by a tamper and neutron reflector of tungsten carbide and steel, both materials having a combined mass of 2,300 kilograms (5,100 lb). Neutron initiators inside the assembly were activated by the impact of the projectile into the target.

Counter-intuitive design

The material was split almost in half, with at one end a group of rings of highly enriched uranium with 40% of the supercritical mass, and at the other end another group of slightly larger rings with 60% of the supercritical mass, which was fired onto the smaller group, with four polonium-beryllium neutron initiators to make the supercritical mass explode.

A hole in the center of the larger piece dispersed the mass and increased the surface area, allowing more fission neutrons to escape, thus preventing a premature chain reaction. But, for this larger, hollow piece to have minimal contact with the tungsten carbide tamper, it must be the projectile, since only the projectile's back end was in contact with the tamper prior to detonation. The rest of the tungsten carbide tamper surrounded the sub-critical mass target cylinder (called the "insert" by the designers) with air space between it and the insert. This arrangement packs the maximum amount of fissile material into a gun-assembly design.

For the first fifty years after 1945, every published description and drawing of the Little Boy mechanism assumed that a small, solid projectile was fired into the center of a larger, stationary target. However, critical mass considerations dictated that in Little Boy the more extensive, hollow piece would be the projectile. The assembled fissile core had more than two critical masses of uranium-235. This required one of the two pieces to have more than one critical mass, with the larger piece avoiding criticality prior to assembly by means of shape and minimal contact with the neutron-reflecting tungsten carbide tamper. In 2004, John Coster-Mullen, a truck driver and model maker from Illinois who had studied every photograph and document on the Hiroshima bomb to make an accurate model, corrected earlier published accounts.

Fuze system

Arming plugs for a Little Boy type atomic bomb on display at the National Air and Space Museum's Steven F. Udvar-Hazy Center

The fuzing system was designed to trigger at the most destructive altitude, which calculations suggested was 580 meters (1,900 ft). It employed a three-stage interlock system:

• A timer ensured that the bomb would not explode until at least fifteen seconds after release, one-quarter of the predicted fall time, to ensure the safety of the aircraft. The timer was activated when the electrical pull-out plugs connecting it to the airplane pulled loose as the bomb fell, switching it to its internal 24-volt battery and starting the timer. At the end of the 15 seconds, the bomb would be 3,600 feet (1,100 m) from the aircraft, and the radar altimeters were powered up and responsibility was passed to the barometric stage.
• The purpose of the barometric stage was to delay activating the radar altimeter firing command circuit until near detonation altitude. A thin metallic membrane enclosing a vacuum chamber (a similar design is still used today in old-fashioned wall barometers) gradually deformed as ambient air pressure increased during descent. The barometric fuze was not considered accurate enough to detonate the bomb at the precise ignition height, because air pressure varies with local conditions. When the bomb reached the design height for this stage (reportedly 2,000 meters; 6,600 ft), the membrane closed a circuit, activating the radar altimeters. The barometric stage was added because of a worry that external radar signals might detonate the bomb too early.
• Two or more redundant radar altimeters were used to reliably detect final altitude. When the altimeters sensed the correct height, the firing switch closed, igniting the three BuOrd Mk15, Mod 1 Navy gun primers in the breech plug, which set off the charge consisting of four silk powder bags each containing 2 pounds (910 g) of WM slotted-tube cordite. This launched the uranium projectile towards the opposite end of the gun barrel at an eventual muzzle velocity of 300 meters per second (980 ft/s). Approximately 10 milliseconds later the chain reaction occurred, lasting less than 1 microsecond. The radar altimeters used were modified U.S. Army Air Corps APS-13 tail warning radars, nicknamed "Archie", normally used to warn a fighter pilot of another plane approaching from behind.

Rehearsals

Little Boy in the bomb pit on Tinian island, before being loaded into Enola Gay's bomb bay. A section of the bomb bay door is visible on the top right.

The Little Boy pre-assemblies were designated L-1, L-2, L-3, L-4, L-5, L-6, L-7, and L-11. Of these, L-1, L-2, L-5, and L-6 were expended in test drops. The first drop test was conducted with L-1 on 23 July 1945. It was dropped over the sea near Tinian in order to test the radar altimeter by the B-29 later known as Big Stink, piloted by Colonel Paul W. Tibbets, the commander of the 509th Composite Group. Two more drop tests over the sea were made on 24 and 25 July, using the L-2 and L-5 units in order to test all components. Tibbets was the pilot for both missions, but this time the bomber used was the one subsequently known as Jabit. L-6 was used as a dress rehearsal on 29 July. The B-29 Next Objective, piloted by Major Charles W. Sweeney, flew to Iwo Jima, where emergency procedures for loading the bomb onto a standby aircraft were practiced. This rehearsal was repeated on 31 July, but this time L-6 was reloaded onto a different B-29, Enola Gay, piloted by Tibbets, and the bomb was test dropped near Tinian. L-11 was the assembly used for the Hiroshima bomb, and was fully assembled with its nuclear fuel by 31 July.

Bombing of Hiroshima

Main article: Atomic bombings of Hiroshima and Nagasaki § Bombing of Hiroshima

Enola Gay after Hiroshima mission, entering hardstand. It is in its 6th Bombardment Group livery, with victor number 82 visible on fuselage just forward of the tail fin.

Parsons, the Enola Gay's weaponeer, was concerned about the possibility of an accidental detonation if the plane crashed on takeoff, so he decided not to load the four cordite powder bags into the gun breech until the aircraft was in flight. After takeoff, Parsons and his assistant, Second Lieutenant Morris R. Jeppson, made their way into the bomb bay along the narrow catwalk on the port side. Jeppson held a flashlight while Parsons disconnected the primer wires, removed the breech plug, inserted the powder bags, replaced the breech plug, and reconnected the wires. Before climbing to altitude on approach to the target, Jeppson switched the three safety plugs between the electrical connectors of the internal battery and the firing mechanism from green to red. The bomb was then fully armed. Jeppson monitored the bomb's circuits.

The mushroom cloud over Hiroshima after the detonation of Little Boy on 6 August 1945. A separation between the upper mushroom head and the stem is visible. This photograph and its vaguely question mark appearance was used as the inspiration for the insignia of the Manhattan Engineer District, and was widely reprinted globally within days of the attack.

The bomb was dropped at approximately 08:15 (JST) on 6 August 1945. After falling for 44.4 seconds, the time and barometric triggers started the firing mechanism. The detonation happened at an altitude of 1,968 ± 50 feet (600 ± 15 m). It was less powerful than the Fat Man, which was dropped on Nagasaki, but the damage and the number of victims at Hiroshima were much higher, as Hiroshima was on flat terrain, while the hypocenter of Nagasaki lay in a small valley. According to figures published in 1945, 66,000 people were killed as a direct result of the Hiroshima blast, and 69,000 were injured to varying degrees. Later estimates put the deaths as high as 140,000 people. The United States Strategic Bombing Survey estimated that out of 24,158 Imperial Japanese Army soldiers in Hiroshima at the time of the bombing, 6,789 were killed or missing as a result of the bombing.

The exact measurement of the explosive yield of the bomb was problematic since the weapon had never been tested. President Harry S. Truman officially announced that the yield was 20 kilotons of TNT (84 TJ). This was based on Parsons's visual assessment that the blast was greater than what he had seen at the Trinity nuclear test. Since that had been estimated at 18 kilotons of TNT (75 TJ), speech writers rounded up to 20 kilotons. Further discussion was then suppressed, for fear of lessening the impact of the bomb on the Japanese. Data had been collected by Luis Alvarez, Harold Agnew, and Lawrence H. Johnston on the instrument plane, The Great Artiste, but this was not used to calculate the yield at the time. More rigorous estimates of the bomb yield and conventional bomb equivalent were made when more data was acquired following the end of the war. A 1985 study estimated the bomb's yield was around 15 kilotons of TNT (63 TJ).

Further information: Little boy § Conventional weapon equivalent

Physical effects

The General Effects of the Atomic Bombs on Hiroshima and Nagasaki, a U.S. Air Force film

After being selected in April 1945, Hiroshima was spared conventional bombing to serve as a pristine target, where the effects of a nuclear bomb on an undamaged city could be observed. While damage could be studied later, the energy yield of the untested Little Boy design could be determined only at the moment of detonation, using instruments dropped by parachute from a plane flying in formation with the one that dropped the bomb. Radio-transmitted data from these instruments indicated a yield of about 15 kilotons.

Comparing this yield to the observed damage produced a rule of thumb called the 5 pounds per square inch (34 kPa) lethal area rule. Approximately all the people inside the area where the shock wave carried such an overpressure or greater would be killed. At Hiroshima, that area was 3.5 kilometers (2.2 mi) in diameter.

The damage came from three main effects: blast, fire, and radiation.

Blast

The blast from a nuclear bomb is the result of X-ray-heated air (the fireball) sending a shock wave or pressure wave in all directions, initially at a velocity greater than the speed of sound, analogous to thunder generated by lightning. Knowledge about urban blast destruction is based largely on studies of Little Boy at Hiroshima. Nagasaki buildings suffered similar damage at similar distances, but the Nagasaki bomb detonated 3.2 kilometers (2.0 mi) from the city center over hilly terrain that was partially bare of buildings.

Frame house in 1953 nuclear test, 5 psi overpressure

In Hiroshima, almost everything within 1.6 kilometers (1.0 mi) of the point directly under the explosion was completely destroyed, except for about 50 heavily reinforced, earthquake-resistant concrete buildings, only the shells of which remained standing. Most were completely gutted, with their windows, doors, sashes, and frames ripped out. The perimeter of severe blast damage approximately followed the 5 pounds per square inch (34 kPa) contour at 1.8 kilometers (1.1 mi).

Later test explosions of nuclear weapons with houses and other test structures nearby confirmed the 5 psi overpressure threshold. Ordinary urban buildings experiencing it were crushed, toppled, or gutted by the force of air pressure. The picture at right shows the effects of a nuclear bomb-generated 5 psi pressure wave on a test structure in Nevada in 1953.

A major effect of this kind of structural damage was that it created fuel for fires that were started simultaneously throughout the severe destruction region.

Fire

The first effect of the explosion was blinding light, accompanied by radiant heat from the fireball. The Hiroshima fireball was 370 meters (1,200 ft) in diameter, with a surface temperature of 6,000 °C (10,830 °F), about the same temperature as at the surface of the sun. Near ground zero, everything flammable burst into flame. One famous, anonymous Hiroshima victim, sitting on stone steps 260 metres (850 ft) from the hypocenter, left only a shadow, having absorbed the fireball heat that permanently bleached the surrounding stone. Simultaneous fires were started throughout the blast-damaged area by fireball heat and by overturned stoves and furnaces, electrical shorts, etc. Twenty minutes after the detonation, these fires had merged into a firestorm, pulling in surface air from all directions to feed an inferno which consumed everything flammable.

Hiroshima blast and fire damage, U.S. Strategic Bombing Survey map

The Hiroshima firestorm was roughly 3.2 kilometers (2.0 mi) in diameter, corresponding closely to the severe blast-damage zone. (See the USSBS map, right.) Blast-damaged buildings provided fuel for the fire. Structural lumber and furniture were splintered and scattered about. Debris-choked roads obstructed firefighters. Broken gas pipes fueled the fire, and broken water pipes rendered hydrants useless. At Nagasaki, the fires failed to merge into a single firestorm, and the fire-damaged area was only one-quarter as great as at Hiroshima, due in part to a southwest wind that pushed the fires away from the city.

As the map shows, the Hiroshima firestorm jumped natural firebreaks (river channels), as well as prepared firebreaks. The spread of fire stopped only when it reached the edge of the blast-damaged area, encountering less available fuel. The Manhattan Project report on Hiroshima estimated that 60% of immediate deaths were caused by fire, but with the caveat that "many persons near the center of explosion suffered fatal injuries from more than one of the bomb effects."

Radiation

Local fallout is dust and ash from a bomb crater, contaminated with radioactive fission products. It falls to earth downwind of the crater and can produce, with radiation alone, a lethal area much larger than that from blast and fire. With an air burst, the fission products rise into the stratosphere, where they dissipate and become part of the global environment. Because Little Boy was an air burst 580 meters (1,900 ft) above the ground, there was no bomb crater and no local radioactive fallout.

However, a burst of intense neutron and gamma radiation came directly from the fission of the uranium. Its lethal radius was approximately 1.3 kilometers (0.8 mi), covering about half of the firestorm area. An estimated 30% of immediate fatalities were people who received lethal doses of this direct radiation, but died in the firestorm before their radiation injuries would have become apparent. Over 6,000 people survived the blast and fire, but died of radiation injuries. Among injured survivors, 30% had radiation injuries from which they recovered, but with a lifelong increase in cancer risk. To date, no radiation-related evidence of heritable diseases has been observed among the survivors' children.

After the surrender of Japan was finalized, Manhattan Project scientists began to immediately survey the city of Hiroshima to better understand the damage, and to communicate with Japanese physicians about radiation effects in particular. The collaboration became the Atomic Bomb Casualty Commission in 1946, a joint U.S.–Japanese project to track radiation injuries among survivors. In 1975 its work was superseded by the Radiation Effects Research Foundation.

In 1962, scientists at Los Alamos created a mockup of Little Boy known as "Project Ichiban" in order to answer some of the unanswered questions about the exact radiation output of the bomb, which would be useful for setting benchmarks for interpreting the relationship between radiation exposure and later health outcomes. But it failed to clear up all the issues. In 1982, Los Alamos created a replica Little Boy from the original drawings and specifications. This was then tested with enriched uranium but in a safe configuration that would not cause a nuclear explosion. A hydraulic lift was used to move the projectile, and experiments were run to assess neutron emission.

Conventional weapon equivalent

See also: Operation Meetinghouse

After hostilities ended, a survey team from the Manhattan Project that included William Penney, Robert Serber, and George T. Reynolds was sent to Hiroshima to evaluate the effects of the blast. From evaluating the effects on objects and structures, Penney concluded that the yield was 12 ± 1 kilotons. Later calculations based on charring pointed to a yield of 13 to 14 kilotons. In 1953, Frederick Reines calculated the yield as 15 kilotons of TNT (63 TJ). Based on the Project Ichiban data, and the pressure-wave data from The Great Artiste, the yield was estimated in the 1960s at 16.6 ± 0.3 kilotons. A review conducted by a scientist at Los Alamos in 1985 concluded, on the basis of existing blast, thermal, and radiological data, and then-current models of weapons effects, that the best estimate of the yield was 15 kilotons of TNT (63 TJ) with an uncertainty of 20% (±3 kt). By comparison, the best value for the Nagasaki bomb was evaluated as 21 kilotons of TNT (88 TJ) with an uncertainty of 10% (±2 kt), the difference in uncertainty owing to having better data on the latter.

Although Little Boy exploded with the energy equivalent of around 15 kilotons of TNT, in 1946 the Strategic Bombing Survey estimated that the same blast and fire effect could have been caused by 2.1 kilotons of conventional bombs: "220 B-29s carrying 1.2 kilotons of incendiary bombs, 400 tons of high-explosive bombs, and 500 tons of anti-personnel fragmentation bombs." Since the target was spread across a two-dimensional plane, the vertical component of a single spherical nuclear explosion was largely wasted. A cluster bomb pattern of smaller explosions would have been a more energy-efficient match to the target.

Post-war

One of five casings built for the Little Boy bomb used on Hiroshima on display at the Imperial War Museum in London during 2015

Graph of cumulative shipments of U-235 from the Y-12 electromagnetic enrichment plant at Oak Ridge to Los Alamos, 1944-1946

When the war ended, it was not expected that the inefficient Little Boy design would ever again be required, and many plans and diagrams were destroyed. However, by mid-1946 the Hanford Site reactors were suffering badly from the Wigner effect. Faced with the prospect of no more plutonium for new cores and no more polonium for the initiators for the cores that had already been produced, the Director of the Manhattan Project, Major General Leslie R. Groves, ordered that some Little Boys be prepared as an interim measure until a solution could be found. No Little Boy assemblies were available, and no comprehensive set of diagrams of the Little Boy could be found, although there were drawings of the various components, and stocks of spare parts.

At Sandia Base, three Army officers, Captains Albert Bethel, Richard Meyer, and Bobbie Griffin attempted to re-create the Little Boy. They were supervised by Harlow W. Russ, an expert on Little Boy who served with Project Alberta on Tinian, and was now leader of the Z-11 Group of the Los Alamos Laboratory's Z Division at Sandia. Gradually, they managed to locate the correct drawings and parts, and figured out how they went together. Eventually, they built six Little Boy assemblies. Although the casings, barrels, and components were tested, no enriched uranium was supplied for the bombs. By early 1947, the problem caused by the Wigner effect was on its way to solution, and the three officers were reassigned.

The Navy Bureau of Ordnance began in 1947 to produce 25 "revised" Little Boy mechanical assemblies for use by the nuclear-capable Lockheed P2V Neptune aircraft carrier aircraft (which could be launched from, but not land on, the Midway-class aircraft carriers). Components were produced by the Naval Ordnance Plants in Pocatello, Idaho, and Louisville, Kentucky. Enough fissionable material was available by 1948 to build ten projectiles and targets, although there were only enough initiators for six. However, no actual fissionable components were produced by the end of 1948, and only two outer casings were available. By the end of 1950, only five complete Little Boy assemblies had been built. All were retired by November 1950.

The Smithsonian Institution displayed a Little Boy (complete, except for enriched uranium), until 1986. The Department of Energy took the weapon from the museum to remove its inner components, so the bomb could not be stolen and detonated with fissile material. The government returned the emptied casing to the Smithsonian in 1993. Three other disarmed bombs are on display in the United States; another is at the Imperial War Museum in London.

References

• Abrahamson, James L.; Carew, Paul H. (2002). Vanguard of American Atomic Deterrence. Westport, Connecticut: Praeger. ISBN 0-275-97819-2. OCLC 49859889.
• "The Atomic Bombings of Hiroshima and Nagasaki" (PDF). The Manhattan Engineer District. 29 June 1946. Archived from the original (PDF) on 6 April 2012. Retrieved 6 November 2013. This report can also be found here and here.
• Bernstein, Jeremy (2007). Nuclear Weapons: What You Need to Know. Cambridge University Press. ISBN 978-0-521-88408-2.
• Campbell, Richard H. (2005). The Silverplate Bombers: A History and Registry of the Enola Gay and Other B-29s Configured to Carry Atomic Bombs. Jefferson, North Carolina: McFarland & Company. ISBN 0-7864-2139-8. OCLC 58554961.
• Coster-Mullen, John (2012). Atom Bombs: The Top Secret Inside Story of Little Boy and Fat Man. Waukesha, Wisconsin: J. Coster-Mullen. OCLC 298514167.
• Craven, W. F.; Cate, J. L., eds. (1983). The Pacific: Matterhorn to Nagasaki, June 1944 to August 1945. The Army Air Forces in World War II. Vol. 5. Washington, D.C.: Office of Air Force History. OCLC 9828710. Retrieved 28 March 2023.
• Diacon, Diane (1984). Residential Housing and Nuclear Attack. London: Croom Helm. ISBN 978-0-7099-0868-5.
• D'Olier, Franklin, ed. (1946). United States Strategic Bombing Survey, Summary Report (Pacific War). Washington: United States Government Printing Office. Retrieved 6 November 2013. This report can also be found here.
• "Genetic Effects: Question #7". Radiation Effects Research Foundation. Retrieved 6 November 2013.
• Glasstone, Samuel (1962). The Effects of Nuclear Weapons, Revised Edition. United States: United States Department of Defense and United States Atomic Energy Commission. ISBN 978-1258793555.
• Glasstone, Samuel; Dolan, Philip J. (1977). The Effects of Nuclear Weapons, Third Edition. United States: United States Department of Defense and United States Department of Energy. ISBN 978-1603220163.
• Gosling, F. G. (1999). The Manhattan Project: Making the Atomic Bomb. Diane Publishing. ISBN 978-0-7881-7880-1.
• Groves, Leslie R. (1962). Now it Can Be Told: the Story of the Manhattan Project. New York: Da Capo Press (1975 reprint). ISBN 0-306-70738-1.
• Hansen, Chuck (1995). Volume V: US Nuclear Weapons Histories. Swords of Armageddon: US Nuclear Weapons Development since 1945. Sunnyvale, California: Chuckelea Publications. ISBN 978-0-9791915-0-3. OCLC 231585284.
• Hansen, Chuck (1995a). Volume VII: The Development of US Nuclear Weapons. Swords of Armageddon: US Nuclear Weapons Development since 1945. Sunnyvale, California: Chuckelea Publications. ISBN 978-0-9791915-7-2. OCLC 231585284.
• Hewlett, Richard G.; Anderson, Oscar E. (1962). The New World, 1939–1946 (PDF). University Park: Pennsylvania State University Press. ISBN 0-520-07186-7. OCLC 637004643. Retrieved 26 March 2013.
• Hoddeson, Lillian; Henriksen, Paul W.; Meade, Roger A.; Westfall, Catherine L. (1993). Critical Assembly: A Technical History of Los Alamos During the Oppenheimer Years, 1943–1945. New York: Cambridge University Press. ISBN 0-521-44132-3. OCLC 26764320.
• "Human Shadow Etched in Stone". Photographic Display. Hiroshima Peace Memorial Museum. Archived from the original on 20 July 2021. Retrieved 6 November 2013.
• Izumi S, Koyama K, Soda M, Suyama A (November 2003). "Cancer incidence in children and young adults did not increase relative to parental exposure to atomic bombs". British Journal of Cancer. 89 (9): 1709–1713. doi:10.1038/sj.bjc.6601322. PMC 2394417. PMID 14583774.
• Izumi S, Suyama A, Koyama K (November 2003). "Radiation-related mortality among offspring of atomic bomb survivors: a half-century of follow-up". International Journal of Cancer. 107 (2): 292–297. doi:10.1002/ijc.11400. PMID 12949810. S2CID 23902907.
• Jones, Vincent (1985). Manhattan: The Army and the Atomic Bomb (PDF). Washington, D.C.: United States Army Center of Military History. OCLC 10913875. Archived from the original (PDF) on 7 October 2014. Retrieved 25 August 2013.
• Malik, John S. (1985). "The yields of the Hiroshima and Nagasaki nuclear explosions" (PDF). Los Alamos National Laboratory report number LA-8819. Retrieved 6 November 2013.
• Monk, Ray (2012). Robert Oppenheimer: A Life Inside the Center. New York; Toronto: Doubleday. ISBN 978-0-385-50407-2.
• Nichols, Kenneth (1987). The Road to Trinity: A Personal Account of How America's Nuclear Policies Were Made. New York: William Morrow. ISBN 068806910X. OCLC 15223648.
• "Nuclear Weapon Thermal Effects". Special Weapons Primer, Weapons of Mass Destruction. Federation of American Scientists. 1998. Archived from the original on 22 April 2013. Retrieved 5 November 2013.
• Rhodes, Richard (1986). The Making of the Atomic Bomb. New York: Simon & Schuster. ISBN 0-684-81378-5. OCLC 13793436.
• Rhodes, Richard (1995). Dark Sun: The Making of the Hydrogen Bomb. New York: Touchstone. ISBN 0-684-82414-0.
• Richardson, David; et al. (September 2009). "Ionizing Radiation and Leukemia Mortality among Japanese Atomic Bomb Survivors, 1950–2000". Radiation Research. 172 (3): 368–382. Bibcode:2009RadR..172..368R. doi:10.1667/RR1801.1. PMID 19708786. S2CID 12463437.
• Samuels, David (15 December 2008). "Atomic John: A truck driver uncovers secrets about the first nuclear bombs". The New Yorker. Retrieved 30 August 2013.
• Serber, Robert; Crease, Robert P. (1998). Peace & War: Reminiscences of a Life on the Frontiers of Science. New York: Columbia University Press. ISBN 978-0231105460. OCLC 37631186.

External links

• Little Boy description at Carey Sublette's NuclearWeaponArchive.org
• Nuclear Files.org Definition and explanation of 'Little Boy'
• The Nuclear Weapon Archive
• Simulation of "Little Boy" an interactive simulation of "Little Boy"
• Little Boy 3D Model
• Hiroshima & Nagasaki Remembered information about preparation and dropping the Little Boy bomb
• Little boy Nuclear Bomb at Imperial War museum London UK (jpg)