Jump to content

Sound board (music)

From Wikipedia, the free encyclopedia

This is an old revision of this page, as edited by Joelthesecond (talk | contribs) at 18:32, 3 April 2024 (Dictionary.com, Merriam-Webster, Cambridge, Collins, and the OED all say it is "soundboard"; none of them show results for "sound board". "Sounding board" is included in three of the five dictionaries.). The present address (URL) is a permanent link to this revision, which may differ significantly from the current revision.

Soundboard of a harpsichord with Chladni patterns
A portion of the soundboard of a Vose & Sons upright piano
No. 15 indicates the Soundboard

A soundboard (occasionally called a sounding board) is the surface of a string instrument that the strings vibrate against, usually via some sort of bridge. Pianos, guitars, banjos, and many other stringed instruments incorporate soundboards. The resonant properties of the soundboard and the interior of the instrument greatly increase the loudness of the vibrating strings.[1] "The sound board is probably the most important element of a guitar in terms of its influence on the quality of the instrument's tone [timbre]."[2][3][4]

When the [guitar] top (or soundboard) vibrates, it generates sound waves, much like a loudspeaker. As the soundboard moves forward, the air that is in front of it is compressed and it moves away from the guitar. As the soundboard moves back, the pressure on the air in front of the guitar is reduced. This is called a "rarefaction," and air rushes in to fill the rarefied region. Through this process, an alternating series of compression and rarefaction pulses travel away from the soundboard, creating sound waves.[5]

The soundboard operates by the principle of forced vibration. The string gently vibrates the board, and despite their differences in size and composition, makes the board vibrate at exactly the same frequency. This produces the same sound as the string alone, differing only in timbre. The string would produce the same amount of energy without the board present, but the greater surface area of the soundboard moves a greater volume of air, which produces a louder sound. "Generally, stiffer boards will give a brighter edge to the sound than softer, more flexible boards....A good, dry soundboard has a certain 'live' tone while a poor one will have a relatively dead response", which may be tested during construction by thumping the board and listening for, "brighter, more noticeable ring[ing]", as one works the board, "to the appropriate thinness".[3]

Soundboards are traditionally made of wood (see tonewood), though other materials are used, such as skin or plastic on instruments in the banjo family. Wooden soundboards typically have one or more sound holes of various shapes. Round, oval, or F-holes appear on many plucked instruments, such as guitars and mandolins. F-holes are usual in violin family instruments. Lutes commonly have elaborate rosettes.

The soundboard, depending on the instrument, is called a top plate, table, sound-table, or belly. It is usually made of a softwood, often spruce.[6]

In a grand piano, the soundboard is part of the case. In an upright piano, the soundboard is a large vertical plate at the back of the instrument. The harp has a soundboard below the strings.

More generally, any hard surface can act as a soundboard. An example is when someone strikes a tuning fork and holds it against a table top to amplify its sound.

Production and material

Wood for woodworking must be specially prepared. Ideally, it should be naturally dried. The natural drying process takes at least one year, but it is the only process that preserves the natural structure of the fibres and pores of the wood, which determine the resonance and frequency characteristics of the material. Not only is this process lengthy, but it is also expensive. It would be far quicker and cheaper to subject the wood to artificial drying, although the quality of the material would be compromised. The acoustic properties of an instrument are also influenced by the wood's cutting profile, the direction of its fibres and the lack of knots.[7]

See also

References

  1. ^ Alberto Bachmann (1975), An encyclopedia of the violin, p. 87
  2. ^ Siminoff, Roger H. (2002). The Luthier's Handbook, p.44. Hal Leonard. ISBN 9780634014680. "The soundboard is the most important component of an acoustic instrument. In acoustic terms, it is referred to as a 'plate.'" Or "plaque"".
  3. ^ a b Sloane, Irving (1989). Classic Guitar Construction, p.20. Bold Strummer. ISBN 9780933224148. "The sound board is the most important element in the guitar."
  4. ^ Gerken, Teja; Simmons, Michael; Ford, Frank; and Johnston, Richard (2005). Acoustic Guitar, p.127. Hal Leonard. ISBN 9780634079207. "The soundboard, or top, is the most important component of any guitar, for it is responsible for the majority of the instrument's sound [amplitude]."
  5. ^ Price, Huw (2002). Recording Guitar and Bass, p.72. Hal Leonard. ISBN 9780879307301.
  6. ^ Montagu, Jeremy (2001). "Belly". In Sadie, Stanley; Tyrrell, John (eds.). The New Grove Dictionary of Music and Musicians (2nd ed.). London: Macmillan Publishers. ISBN 978-1-56159-239-5.
  7. ^ Wegst, Ulrike G. K. (1 October 2006). "Wood for sound". American Journal of Botany. 93 (10): 1439–1448. doi:10.3732/ajb.93.10.1439. ISSN 0002-9122. PMID 21642091. Archived from the original on Apr 17, 2023. Retrieved 2023-04-12 – via ResearchGate.