Jump to content

Electric vehicle conversion

From Wikipedia, the free encyclopedia

This is an old revision of this page, as edited by 12.164.196.101 (talk) at 15:57, 25 May 2008 (→Other trucks - full size and most SUVs). The present address (URL) is a permanent link to this revision, which may differ significantly from the current revision.

An electric vehicle conversion is the modification of a conventional internal combustion engine (ICE) driven vehicle to battery electric propulsion, creating a battery electric vehicle or plug-in hybrid. In some cases the vehicle may be built by the converter, or assembled from a kit car, and vehicles of this type are also noted below.

Vehicles may be converted by a manufacturer (as was done by Ford Motor Company to create the Ford Ranger EV) or by an independent converter that purchases new vehicles without a motor or related equipment (these vehicles are called "gliders"[1] to offer a two-stage vehicle and the procedure is called third-party (power)trainization). A two-stage vehicle is a vehicle that has been built by two separate manufacturers. The result is a standard, complete vehicle.[2]

Most conversions in North America are performed by hobbyists who typically will convert a well used vehicle with a non-functioning engine, since such defective vehicles can be quite inexpensive to purchase. Other hobbyists with larger budgets may prefer to convert a later model vehicle, or a vehicle of a particular type.

In some countries, the user can choose to buy a converted vehicle of any model in the automaker dealerships only paying the cost of the batteries and motor, with no installation costs (it is called preconversion or previous conversion).

Elements of a conversion

  • The battery pack, which provides a source of electrical power. The most commonly available and affordable batteries are lead acid flooded type. Next are the AGM (Absorption Glass Mat) sealed maintenance free batteries, a little more powerful and expensive. Then there are the more exotic batteries like NI-MH and LI-ION; more difficult to find but light and longer lasting, maintenance free, and much more expensive. The new lithium batteries are showing some promise for EVs in the near future.
  • The charger which restores energy to the batteries (which may be mounted within the vehicle or at a special charging station at some fixed location)
  • The power controller, which regulates the flow of energy between the battery and the motor(s), controlled by an electronic throttle.
  • One or more electric motors and their mechanical attachment to the driveline
  • Power conductors connecting the battery, controller, and motor(s)
  • Accessory equipment to power auxiliary equipment such as power brakes and heating system
  • Control circuitry and equipment to allow control and interlocking of the various components
  • Instrumentation specific to the operation and maintenance of the conversion

Vehicle types (including scratch built)

== == LOW COST ELECTRIC VEHICLE ==Electric two wheelers , three wheelers and four wheelers conversion is done very easily just by selecting apropriate donor automotive vehicle. 

===Electric bicycle===

An electric bicycle is a class of bicycles that are fitted with an electric motor. Often they are powered by rechargeable batteries however some experimental electric bicycles run directly on or recharge their batteries via solar panels, fuel cells, gas generators or other alternative energy sources. Some experimenters have even used super capacitors to store energy. Using an on-board generator may impact the legal jurisdictional definition of an electric bicycle. A few types of electric bicycles are able to re-capture energy from braking and can re-charge the batteries while braking or travelling down hills (regenerative braking). With the advent of newer technology further features can be expected.

Some electric bikes have features where the motor can move the bicycle by itself if the rider chooses not to pedal, while others require the rider to pedal at all times. This latter type may in some jurisdictions allow the vehicle to be used on bicycle trails that otherwise prohibit motorized vehicles of any kind. (See motorized bicycle).

The conversion of a bicycle to electric power is probably the lowest cost means of learning conversion methods. Battery packs are usually lead acid gel cells since these are available in small sizes suitable for this application. It is also practical to experiment with more expensive battery types since only a small pack is required. It is possible to repurpose battery packs and chargers intended for powering toys and similar small electrical devices.

Electric motorcycle and Scooters

Low speed Scooters are not typically suitable for on the road use. These may be configured for either standing or sitting use. Some local laws apply bicycle laws to such scooters such as helmet and pedestrian right of way considerations.

Motorcycle conversions are a specialty niche which can offer an opportunity to build a relatively low cost electric vehicle. Most of these use a two wheel configuration, although the two types of three wheel vehicle (and sometimes four wheel vehicles) are classified as motorcycles in many jurisdictions if their weight is sufficiently low (typically around 500 kg/1000 pounds maximum). If a tricycle layout is employed, greater handling stability is obtained with the single wheel at the back, with normal automotive type front wheel steering, as compared with placing the single wheel in the front.

Economy coupe

This elderly fiat employs batteries that can be mounted in any position

Owing to its light weight and efficiency, a light vehicle can make an excellent choice- particularly if care is taken in component selection and placement. It is possible to obtain conversion kits for some popular light vehicles, most notably the rear motor, rear drive Volkswagen Beetle, its Type 3 evolution, and its successor, the front motor/drive VW Rabbit.

By converting a light vehicle it is possible to use a smaller motor, which both weighs and costs less than a larger motor. A lighter overall vehicle weight will reduce power consumption in start and stop traffic and so increase range in many practical driving conditions.

(At least one commercial converter, Solectria, had converted the front wheel drive General Motors Geo Metro for electric use, creating the Solectria Force. Solectria was acquired by Azure Dynamics of Canada in January 2005 and now focuses on electric and hybrid fleet vehicles.)

Canadian Electric Vehicles have conversion kits for an electric Geo and a whole range of vehicles from compacts to trucks.

Compact sedan or coupe

A compact sedan may be a better choice than a subcompact owing to better load capacity and more room for battery placement. Some commercial EV Conversions use vehicles in this size range. One example is a 1992 Honda Civic [4]. In this conversion, the back seat was retained, and there is still enough room to sink nine flooded lead acid batteries low in the trunk where the spare tire was located, as well as another nine batteries under the hood. With suspension modifications, (increasing shock length & spring rating), the car must still be below GVWR , even with the driver and passengers. Exceeding the total design weight of the vehicle would be illegal.

Full size sedan

Full size sedans and minivans are generally considered to be poor candidates for EV conversion. As the suspensions and tires are already operating close to the maximum permissible it may be necessary to make substantial modifications in these areas. It may be easier to obtain upgraded suspension components for some smaller vehicles, if these are also typically used for sports racing (particularly autocross). Starting with a heavy vehicle and adding batteries will result in poor performance in acceleration, handling, braking, and economy of operation.

Sports car

For a person interested in sports car performance and appearance, the creation of a satisfying conversion will likely lead to a number of difficulties in such details as battery disposition, as such vehicles generally have available space distributed in small volumes around the vehicle. This leads to complexity in securing and wiring batteries. Such vehicles can offer stunning performance in the lower speed ranges owing to light weight and rear wheel drive and may also offer good range from their superior aerodynamics.

The 1969-1976 Porsche 914 is one of the more successful sportscar conversions, as well as being one of the most popular. Once converted, it boasts better performance in range, acceleration and top speed than most other vehicles. Also, its low aquistion costs contributes to its popularity as a candidate. Some manufacturers of conversion kits have made a kit specific to the 914.

Another popular sportscar used for conversion is the 1984-1989 Toyota MR2 Reasons for its popularity are low weight before conversion, low cost to purchase the car, and available locations within the car to place the large batteries that most people use (lead-acid and its derivative technologies). The later MR2 body style (Mark 2) does not seem as popular, and as of March 2008, there is only one known conversion Toyota is also known for its hybrid Prius, and the Toyota Rav4 EV.

Tesla Motors has produced a high end electric sports car (with exceptional performance), although not a conversion but rather being of new construction following an electrically powered initial design. Such a performance vehicle suggests what converters may be able to do once there is a ready access to lightweight and powerful batteries. For a non-production conversion using such batteries and a modern A/C motor and controller see Wrightspeed X1.

Sterling Sports Cars LLC Low cost sports car conversion option. If appearance is as important as performance this company offers DIY options and turnkey cars. Very aerodynamic and space for battery options. Retro European styling from the 70's with modern details.

The Bradley GT II as well as other VW based kit cars are very popular conversion candidates due to their being inexpensive, extensive support groups as well as their simple sports car design. Availability of conversion kits for these cars are quite prevalent with commercial retail establishments that specialize in EV conversions.

Light truck

Light trucks are especially suitable for hobbyist conversion because it is easy to locate batteries remote from the passenger compartment and there is a good load handling capacity for the use of heavy batteries such as the flooded lead-acid batteries commonly used in golf carts. Light trucks also offer substantial utility in use simply because they are trucks.. Even if a portion of the weight capacity is removed by the presence of batteries within the cargo bed, much of the spacial utility remains. A light truck is highly recommended as a first conversion effort because of the simplicity of component layout. With proper battery placement the stability of a late production truck can be improved over the ICE version. While a number of suitable vehicles are available in pre-2000 models, the modern evolution of this type has become taller, heavier, and less efficient, and their excessive height makes under-bed battery placement necessary to keep the center of gravity low.

Canadian Electric Vehicles produce conversions for many types of vehicles - including light trucks.

Other trucks - full size and most SUVs

These are rarely converted due to their excessive weight, and aerodynamic inefficiencies. To make the situation worse, many modern trucks/SUVs continue to get bulkier, heavier, and their high stance means the height of the center of gravity leads to instability while making high speed turns, a distinct disadvantage if there not enough room between the frame rails to enable low battery mounting. As a direct result, the payload carrying capacity and thus the GVWR of the vehicles goes down. Such a trait is not desirable because it limits the weight of the battery pack that can be carried, limiting the maximum battery-to-vehicle weight ratio that could be achieved for the vehicle when converted to an EV. (Such considerations are important due to current price, weight, and performance limitations current battery technoligies.) For a given battery type, reducing the battery-to-vehicle weight ratio always results in reduced vehicle range per charge. However, despite these mostly unavoidable limitations, several SUVs and larger trucks have been successfully converted to electric power by hobbyists. Some examples include the "Gone Postal" van converted to an EV racer by Roderick Wilde and Suckamps EV Racing, the 1971 Land Rover EV converted by Wilde Evolutions, and the 1988 Jeep Cherokee EV converted by Nick Viera.

Electric buses

The principle efforts in the development electric buses without trolleys and wires have involved limited production of very expensive fuel cell vehicles. Most economically effective development in this area involves the creation of hybrid buses, well suited to this application owning to frequent stops and starts and effective energy recovery and release in this cycle. Another solution is the use of battery electric buses that follow the principle of replacing (discharged batteries) instead of recharging.

Racers

Hotrod

While this type of vehicle is usually made to be a "street-legal" performance machine, it may also be developed for occasional use as a drag racing vehicle. The leading vehicle in this field is the "Maniac Mazda" [5] a Mazda RX-7 sports car converted from rotary engine to electric by Roderick Wilde. This vehicle can outrun Dodge Viper and Ferrari sports cars in quarter mile drag races.

Autocross racer

EVs may prove to be especially suitable for autocross contests as low speed acceleration is especially important to success in this type of racing. Specific classes for electric autocross (called electrocross ) are being introduced in some venues. Vehicles for these will typically be economy car conversions or custom built chassis but with excess rear weight bias to allow agile handling under the control of an experienced driver (such rearward balance may be dangerous for everyday use).

Drag racer

Intended only for specialized straight line quarter mile (acceleration) racing this type of vehicle is used only "off road" at specialized "drag strips".

High speed straight line racer

Even more specialized than the drag racer this is intended to obtain high speeds on long, straight, and flat raceways, such as the dry lake beds found in locations such as the Bonneville Salt Flats.

Custom chassis

Suitable for a builder who is capable of constructing a kit car, with good abilities and equipment in machining and welding this can result in a unique vehicle. It is especially suitable for the construction of a lightweight vehicle that can offer exceptional performance.

A glider kit includes all components of a vehicle except the power train.[3][4][5]

Electric Boats

[6] Electric boats offer the ability to have a powered boat on lakes that exclude gasoline motors. Edison Marine has built a 17' solid mahogany runabout with dual electric motors for just these applications. These boats offer more options for boaters who want an electric powered boat that has the looks and aesthetics of the runabouts of the past. These boats are primarily cocktail cruisers and will run all day at 5-7 knots. They are capable of speeds exceeding 30 MPH for about ten minutes at a time. High speed operation does shorten overall run time.

Novelty solar vehicle

At the 2005 Stanford University EV Gathering

Above: Bob Schneeveis[7][8][9] demonstrates his Silver Sofa to the delight of his passengers. This can spin rapidly in place as does a carnival ride and its batteries are recharged by the solar panels.

A novelty vehicle or an electric powered art car may not be suitable for on road use. Applications include electric vehicle show demonstrations, parades, parade floats, float towing, and eclectic off-road gatherings such as Burning Man. This vehicle is ideal for the beach (where not prohibited) and to promote tourist places but will usually require trailering to its operating site.

Registration of converted and newly constructed vehicles

The ease of registration will vary by state. Some states require safety inspections, usually to ensure body integrity in areas subject to severe corrosion from winter road de-icing materials. In any case, for general registration all functional safety equipment should be operating - turn signals, brake lights, headlights, horn, etc. The windshield should have no running cracks (small stone chips and "stars" may be acceptable if not in the driver's principle line of vision) If the vehicle has been reconstructed from a salvage vehicle (a vehicles whose registration has been forfited) inspection may be more severe to ensure compliance.

Registration procedures will vary by state and will usually be more difficult (even bizarre) in states with strict emissions requirements (even though a plug-in only conversion will be a zero emission vehicle). Arguing with DMV staff is typically futile in all jurisdictions, but there may be appeal procedures available but whose availability may not be openly publicized.

California (US) conversion registration and taxation

Registration of a converted electric vehicle in California can be difficult. First, if the vehicle is custom built from components and salvage, only a limited number of such vehicles may be registered each year (as of 2008 this is 500 vehicles). Registration slots are usually gone on the first available day of the year and registration requires a "paper trail" on all salvage components, this to inhibit illegal vehicle "chop shop" operations.

Nor is it possible to convert to electric power and register for on-road use a vehicle that would otherwise not qualify for registration (for example, certain subcompact "Kei car" class trucks, four wheel sport "dirt" vehicles, and other utility vehicles are imported and sold for "off road" use only; these cannot qualify for registration except perhaps if a custom body is installed to allow its qualification under the custom manufacture rules outlined above. Some possiblity may exist for registering such a vehicle as a speed-limited neighborhood electric vehicle.

As all originally ICE roadable automobiles and light trucks built after 1975 must pass a smog test (including a "visual inspection") a conversion of such a late model vehicle must be registered as an electric powered only vehicle and thus exempt, otherwise it would fail the required smog test, not for producing polution, but rather for being altered from its original configuration and so failing the visual inspection portion of the test.

It is no more simple if the vehicle is currently registered with current tags in California and may even be more difficult. Under new 2008 regulations for converted ICE vehicles a multi-step process is required. First, an appointment is made by telephone with a "Smog Referee". A meeting with the vehicle to be registered will typically be at a local junior college with an automotive shop program. The referee will inspect and certify that the vehicle is both smog exempt and that it qualifies for an "E" power code (electric only). The next step requires real-time coordination between a cooperative clerk at the local California Department of Motor Vehicles (DMV) office and an appropriate clerk at the Sacramento office. (These procedures are in place to inhibit fraudulant registration of ICE vehicles as Electric in order to avoid smog inspections.) If the computer terminals are not operated in a coordinated manner the registration propulsion code will default to "Q" (hybrid vehicle) which is not exempt from smog inspection and the conversion will always fail such an inspection. Unfortunately, once the computer has defaulted to the "Q" code it is necessary to re-engage the Smog Referee to obtain a new prospective "E" code. The ability to sucessfully register as an electric vehicle is highly dependant upon the cooperation of the staff at the local office, their experience with registering electric vehicles, their ability to coordinate with Sacramento, and their interest in assisting you. Some offices will be much more accommodating than others. Multiple trips to the DMV office and the Referee are typically required.

Since no fuel or recharging taxes are collected the revenue that would otherwise be lost to the state is made up for with a substantial weight fee specific to electric vehicles registered for commercial use (no weight charges are added for noncommercial vehicles). While light ICE vehicles are taxed on a refined and progressive grading scheme, electric vehicles with commercial licences are grouped into only a few broad catagories, with the result that even a modest and lightweight commercially registered EV will pay the same tax as will a much heaver (up to 6000 lbs) EV.[6] If an open-bed pickup truck (as opposed to a panel truck) is converted, the only way to register as a non-commercial vehicle (and so avoid the weight fees) is to permanently install a camper shell (not a bed cover), which need not project above the truck cab nor include any other "camping" equipment. (This can be inconvenient if access to an in-bed battery box is required.) In California, one advantage of a commercial license is the ability to park in yellow zones, but only for short term pick-up and delivery.

See also

References

  1. ^ Vehicle analysis, pg 14 (PDF)
  2. ^ Titling - Homemade, Two-Stage or Reconstructed Vehicle
  3. ^ NYS DMV - (Brochure) Let the Buyer Be Aware
  4. ^ Energy Storage Fuel Cell Vehicle Analysis: Preprint
  5. ^ Glider Kits & Kit Vehicles
  6. ^ http://www.dmv.ca.gov/pubs/vctop/d03/vc9400.htm Weight Fees for Commercial Motor Vehicles with Declared Gross Vehicle Weight 10,000 lbs. or Less
Wikibooks has more on the topic of: Electric vehicle conversion
Retrieved from "https://en.wikipedia.org/enwiki/w/index.php?title=Electric_vehicle_conversion&oldid=214851222"