Transfer case

A transfer case is a part of a four wheel drive system found in four wheel drive and all wheel drive vehicles. The transfer case is connected to the transmission and also to the front and rear axles by means of drive shafts. It is also referred to as a "transfer gearcase", "transfer gearbox","transfer box" or "jockey box" (Australia).

Functions

• The transfer case receives power from the transmission and sends it to both the front and rear axles. This can be done with a set of gears, but the majority of transfer cases manufactured today are chain driven. On some vehicles, such as four wheel drive trucks or vehicles intended for off-road use, this feature is controlled by the driver. The driver can put the transfer case into either "two wheel drive" or "four wheel drive" mode. This is sometimes accomplished by means of a shifter, similar to that in a manual transmission. On some vehicles this may be electronically operated by a switch instead. Some vehicles, such as all wheel drive sports cars, have transfer cases that are not selectable. Such a transfer case is permanently "locked" into all-wheel-drive mode.

• The transfer case may contain one or more sets of low range gears. Low range gears are engaged with a shifter or electronic switch. On many transfer cases, this shifter is the same as the one that selects 2WD or 4WD operation. Low range gears slow down the vehicle and increase the torque available at the axles. Low-range gears are used during slow-speed or extreme off road maneuvers, such as rockcrawling, or when pulling a heavy load. This feature is often absent on all wheel drive sports cars. Some very large vehicles, such as heavy equipment or military trucks, have more than one low-range gear.

Types of transfer cases

Those used on "part-time four-wheel drive" system off-road vehicles such as trucks, truggies, rock-crawling vehicles, and some military vehicles generally allow the driver to select 2WD versus 4WD as well as high versus low gear ranges. Those used in sports cars are usually "transparent" to the driver; there is no shifter or select lever.

There are two different types of "internal workings" found in most transfer cases. Gear-driven transfer cases can use sets of gears to drive either the front or both the front and rear driveshafts. These are generally strong, heavy units that are used in large trucks, but there are currently several gear drive cases in production for passenger cars.

Chain-driven transfer cases use a chain to drive most often only the front axle, but can drive both axles. Chain-driven transfer cases are quieter and lighter than gear-driven ones. They are used in vehicles such as compact trucks, full size trucks, Jeeps and SUVs. Some off-road driving enthusiasts modify their vehicles to use gear-driven transfer cases, accepting the additional weight and noise to gain the extra strength they generally provide.

Transfer cases are also classified as either "independent" or "married". "Married" transfer cases are bolted directly to the transmission. Sometimes a "married" transfer case is an integral part of the transmission and the two components share the same housing, as is commonly found on modern Subaru products and other four-wheel drive cars. An "independent" transfer case is completely separate from the transmission; it is bolted to the transmission output shaft and a short driveshaft travels from the transfer case to the front and rear differentials. Married transfer cases are by far the most common found in cars. Most pickups and SUVs use an independent transfer case. In fact, this is so common that the term "married" is rarely used. Independent transfer cases are used on very long wheelbase vehicles, such as commercial trucks or military trucks.

Manual transfer cases have a selector lever on the driver's side floor transmission hump and may also have either two sealed automatic front axle locking hubs or two manual front axle hub selectors of "LOCK" and "UNLOCK" or "FREE". To engage the four wheel drive system the vehicle must be moving at a slow speed less than 30 miles per hour, this is only for the four wheel drive high setting. To engage the four wheel drive low setting the vehicle must be stopped and the transmission must be shifted to neutral, then the four wheel drive low can be selected.

Electronic Shift On-the-Fly (ESOF) transfer cases have a dash-mounted selector switch or buttons with front sealed automatic locking axle hubs. Some models also have what is called selec trac which has a slider switch on the center console. This was usually found in the Jeep Cherokee vehicles. Unlike the manual transfer case, this system has a transfer case motor and vacuum operated front hubs. To engage or disengage, the vehicle can be completely stopped or moving at any speed under 55 mph.

Most mud trucks are set up with a transmission and dual transfer cases because of the high relocation after a massive body lift is installed. This saves money on custom drive shafts for high pinion angles. Most of the time, monster trucks and mud trucks are full time four wheel drive and aren't set up with a transmission at all, just an independent three speed transfer case. These trucks are set up to be run at one constant speed and only need to have 1 to 2 gears plus reverse.

See also

• Transmission (mechanics)
• AMC/Jeep Transmissions
• Jeep four wheel drive systems
• four wheel drive