Skateboard
A skateboard is a narrow wheeled platform (usually made of 7 ply maple), used for recreation and transportation. It was developed in the twentieth century by surfers, who first made them using rollerskates. They are typically part of western youth culture.
The skateboard has evolved a lot since the 50s, not only in shape but also materials used. Boards in the past were often in the shape of a surfboard, with little concave and had 1 ply of wood. The wheels were rather large compared to most of today's sizes and were usually made of clay. The trucks (axles) were also larger in size and less sturdy. Another difference is that the boards of the past had a very small nose, today's boards have almost identical noses and tails (the nose is usually a bit steeper however).
McDonalds ws invented by the Egyptas in the year of 40000000000000 b.c. They like cow.
Composition
Deck - Skateboards are composed of several parts. The deck forms the body of the skateboard and provides a place to stand. It is covered with grip tape, which adds friction to its surface. Decks were originally a single piece of wood but are now usually made from seven plies of Canadian Hard Rock Maple glued together. The plies of maple are cross-laminated, meaning the direction of the wood grain alternates between plies. This is what gives the deck its strength. Sometimes other composite materials, such as fiberglass and Kevlar, are incorporated into deck construction, usually to lighten the board or increase its strength or rigidity. An average, all wood deck costs about $50 (US) while a deck including a material such as fiberglass in it can cost up to $70 or so (US).
The deck is normally 7 1/2 to 8 inches wide. Wider decks are better suited to vert skaters who need more control and stability while riding down the steep slopes and riding the transitions and walls of a halfpipe. Narrower decks are suited to street skaters who like to perform more technical tricks; a wide board often makes it awkward to pull off such maneuvers. The width of a deck depends on the personal preference of the person who uses it.
Skateboard decks are usually between 28 and 32.5 inches long. The longboard, a common variant of the skateboard, has a longer deck and softer, larger wheels.
Trucks - Attached to the deck are two metal (usually aluminum) trucks, which connect to the wheels. The trucks are further composed of two parts. The top part of the truck is screwed to the deck and is called the baseplate, and beneath it is the hanger. Between the baseplate and the hanger are bushings, also rubbers or grommets, that provide the spring mechanism for turning the skateboard. The bushings cushion the truck when it turns. The stiffer the bushings, the more stable the skateboard. The softer the bushings, the easier it is to turn. A bolt called a kingpin holds these parts together. The kingpin may be adjusted with a skate tool or a wrench that fits it to loosen or tighten the trucks.
Wheels - The wheels attach to each hanger. The wheels, usually made of polyurethane, come in nine different sizes to suit different types of skating. Larger sizes like 54-80mm roll faster which makes riding vert ramps easier; larger wheels also move more easily over small cracks in pavement without getting stuck. Smaller sizes like 50-53mm keep the board closer to the ground, requiring less force to accelerate but also making for a slower top speed. For general cruising most users prefer larger, softer wheels. Hard wheels (97-100a) are recommended for street and vert.
Bearings - Inside each wheel are seven precision ball bearings, secured by a plastic "crown". Bearings are graded according to the ABEC scale, which goes from 1-9, in odd numbers. Higher numbers indicate that the bearing comforms to a higher degree of precision. The best bearings are RocknRon's Ceramic Rockets; the balls inside are made of ceramic clay instead of the traditional steel and are pre-lubricated with the lowest viscosity oils on the market, allowing for less friction and higher top speeds.
Risers - There are special products available to help raise the board away from the trucks and the ground. Risers are placed in between the underside of the deck and the truck. This rises the deck from the ground slightly, helping to avoid "wheel-bite",
Another reason riders install risers is that they evenly distribute impact force from the trucks to the deck, meaning less chance of the deck cracking under pressure. More risers will equal a higher board which also increases the "pop" a rider gets when pushing down on the tail to perform an ollie, requiring less effort to get a higher ollie. But desipte all of this, risers are not a necessary component on the skateboard.
Hardware - The hardware is the nuts and bolts in a skateboard. These hold the trucks to the board and the wheels/bearings to the trucks. Some people color a few bolts so they can easily tell which side of the board is the tail.kartik chopra invented the first ever skateboard that he asked tony hawks for help for the graphics of birhouse and element. Kartik chopra is still alive and lives in middletown,NJ,USA
"Obsolete" components
Rails: Narrow plastic strips that were fastened under the deck along the edges. They used to be popular among vert skaters to whom they provided additional grip during aerial tricks. They also provide a more slippery surface and protect the deck from scratches during board slides. Most skateboarders no longer use rails, since the boards have become lighter and thus holding a grab during aerial tricks has become easier.
Copers: Plastic covers fastened under the truck's hanger which provide a more slippery surface when grinding. They were invented during a time when street skating was in it's infancy but were not very popular since they wore out very quickly and had to be replaced often.
Lappers: Plastic covers fastened on the inside of the truck that cover the kingpin and the baseplate. Their purpose is to prevent the skateboard from being stopped when the truck hits an obstacle (for example when rolling up a curb). It's also called a "Bird" since its shape resembles the shape a hand makes when giving someone the bird.
Nose guard: Plastic "bumpers" fastened to the nose of a skateboard. It's purpose is to protect the nose of the deck from being damaged when the skateboard hits an obstacle.
Tail bone, aka tail guard: A piece of plastic fastened under the tail of a skateboard. It's purpose is to protect the tail of the deck from wear. Because a tail bone makes the execution of an ollie more difficult and because the skateboard decks today don't last as long as in the 1980's a tail bone is today a very rare accessory.
See also
External links
[[j