Smart grid
This article's tone or style may not reflect the encyclopedic tone used on Wikipedia. (February 2010) |
A smart grid is a digitally enabled electrical grid that gathers, distributes, and acts on information about the behavior of all participants (suppliers and consumers) in order to improve the efficiency, importance, reliability, economics, and sustainability of electricity services.
Smart grid policy is organized in Europe as Smart Grid European Technology Platform.[1] Policy in the United States is described in 42 U.S.C. ch. 152, subch. IX § 17381.
Background and goals
The smart grid implies a fundamental re-engineering of the electricity services industry, but focuses on the technical infrastructure.
History
Today's alternating current power grid evolved after 1896, based in part on Nikola Tesla's design published in 1888 (see War of Currents). Many implementation decisions that are still in use today were made for the first time using the limited emerging technology available 120 years ago. Specific obsolete power grid assumptions and features (like centralized unidirectional[2] electric power transmission, electricity distribution, and demand-driven control) represent a vision of what was thought possible in the 19th century.
Part of this is due to an institutional risk aversion that utilities naturally feel regarding use of untested technologies on a critical infrastructure they have been charged with maintaining.[3]
The 20th century power grids were originally built out as local grids which, over time, became interwoven for economic and reliability purposes. One of the largest engineered systems ever constructed, the mature, interconnected electric grid of the late 1960s became conceived of as "dividing and distributing" electric power, on a bulk basis, from a relatively small number (i.e., ~thousands) of "central plant" generating stations, to major load centers, and from there to a large number of individual consumers, large and small. The nature of generating technologies available over the first three-quarters of the 20th century lent themselves to both notable efficiencies of scale (individual plants of 1000-3000 MW were not uncommon) and to situationally-specific locations (hydroelectric plants at high dams, coal-, gas-, and oil-fired plants near supply lines, nuclear plants near supplies of cooling water, and all of them, for a variety of reasons, as far away from population centers as economically possible). As the electric power industry continued to produce ever more-affordable electric power to an ever-increasing base of customers, by the late 1960s it had reached nearly every home and business in the developed world. [references pending]
However, the data-collecting and processing capabilities of the era required broadly averaged, statistical rate classifications that severely limited the timely propagation of supply and demand price signals through the system. At the same time, increasing environmental concerns and increasing sociopolitical dependence on electrification combined to limit further economies of scale. By the end of the 20th century, the cost escalation of electric power in major metropolitan areas was considered untenable, and technologies that would remain recognizable to the founders of the industry from a century earlier were no longer considered adequate to an information- and services-based economy. [references pending]
Over the past 50 years, electricity networks have not kept pace with modern challenges, such as:
- security threats, from either energy suppliers or cyber attack
- national goals to employ alternative power generation sources whose intermittent supply makes maintaining stable power significantly more complex
- conservation goals that seek to lessen peak demand surges during the day so that less energy is wasted in order to ensure adequate reserves
- high demand for an electricity supply that is uninterruptible
- digitally controlled devices that can alter the nature of the electrical load (giving the electric company the ability to turn off appliances in your home if they see fit) and result in electricity demand that is incompatible with a power system that was built to serve an “analog economy.” For a simple example, timed Christmas lights can present significant surges in demand because they come on at near the same time (sundown or a set time). Without the kind of coordination that a smart grid can provide, the increased use of such devices lead to electric service reliability problems, power quality disturbances, blackouts, and brownouts.[4]
Although these points tend to be the "conventional wisdom" with respect to smart grids, their relative importance is debatable. For instance, despite the weaknesses of power network being publicly broadcast, there has never been an attack on a power network in the United States or Europe.[citation needed] However, in April 2009 it was learned that spies had infiltrated the power grids, perhaps as a means to attack the grid at a later time.[5] In the case of renewable power and its variability, recent work undertaken in Europe (Dr. Bart Ummels et al.)[full citation needed] suggests that a given power network can take up to 30% renewables (such as wind and solar) without any changes whatsoever.
Meanwhile, advances in automation, data communications, and distributed generation began to appear adequate to support the concept of a smart grid, which could accommodate suppliers and consumers from a wide range of circumstances, with a greater capacity to anticipate and respond to changing operating conditions, and with greater economic efficiency. [references pending]
The term smart grid has been in use since at least 2005, when the article "Toward A Smart Grid", authored by S. Massoud Amin and Bruce F. Wollenberg appeared in the September/October issue of IEEE P&E Magazine (Vol. 3, No.5, pgs 34–41). The term had been used previously and may date as far back as 1998. There are a great many smart grid definitions, some functional, some technological, and some benefits-oriented. A common element to most definitions is the application of digital processing and communications to the power grid, making data flow and information management central to the smart grid. Various capabilities result from the deeply integrated use of digital technology with power grids, and integration of the new grid information flows into utility processes and systems is one of the key issues in the design of smart grids. Electric utilities now find themselves making three classes of transformations: improvement of infrastructure, called the strong grid in China; addition of the digital layer, which is the essence of the smart grid; and business process transformation, necessary to capitalize on the investments in smart technology. Much of the modernization work that has been going on in electric grid modernization, especially substation and distribution automation, is now included in the general concept of the smart grid, but additional capabilities are evolving as well.
Smart grid technologies have emerged from earlier attempts at using electronic control, metering, and monitoring. In the 1980s, Automatic meter reading was used for monitoring loads from large customers, and evolved into the Advanced Metering Infrastructure of the 1990s, whose meters could store how electricity was used at different times of the day.[6] Smart meters add continuous communications so that monitoring can be done in real time, and can be used as a gateway to demand response-aware devices and "smart sockets" in the home. Early forms of such Demand side management technologies were dynamic demand aware devices that passively sensed the load on the grid by monitoring changes in the power supply frequency. Devices such as industrial and domestic air conditioners, refrigerators and heaters adjusted their duty cycle to avoid activation during times the grid was suffering a peak condition. Beginning in 2000, Italy's Telegestore Project was the first to network large numbers (27 million) of homes using such smart meters connected via low bandwidth power line communication.[7] Recent projects use Broadband over Power Line (BPL) communications, or wireless technologies such as mesh networking that is advocated as providing more reliable connections to disparate devices in the home as well as supporting metering of other utilities such as gas and water[citation needed].
Monitoring and synchronization of wide area networks were revolutionized in the early 1990s when the Bonneville Power Administration expanded its smart grid research with prototype sensors that are capable of very rapid analysis of anomalies in electricity quality over very large geographic areas. The culmination of this work was the first operational Wide Area Measurement System (WAMS) in 2000.[8] Other countries are rapidly integrating this technology — China will have a comprehensive national WAMS system when its current 5-year economic plan is complete in 2012[9]
First cities with smart grids
The earliest, and still largest, example of a smart grid is the Italian system installed by Enel S.p.A. of Italy. Completed in 2005, the Telegestore project was highly unusual in the utility world because the company designed and manufactured their own meters, acted as their own system integrator, and developed their own system software. The Telegestore project is widely regarded as the first commercial scale use of smart grid technology to the home, and delivers annual savings of 500 million euro at a project cost of 2.1 billion euro.[7]
In the US, the city of Austin, Texas has been working on building its smart grid since 2003, when its utility first replaced 1/3 of its manual meters with smart meters that communicate via a wireless mesh network. It currently manages 200,000 devices real-time (smart meters, smart thermostats, and sensors across its service area), and expects to be supporting 500,000 devices real-time in 2009 servicing 1 million consumers and 43,000 businesses.[10] Boulder, Colorado completed the first phase of its smart grid project in August 2008. Both systems use the smart meter as a gateway to the home automation network (HAN) that controls smart sockets and devices. Some HAN designers favor decoupling control functions from the meter, out of concern of future mismatches with new standards and technologies available from the fast moving business segment of home electronic devices.[11]
Hydro One, in Ontario, Canada is in the midst of a large-scale Smart Grid initiative, deploying a standards-compliant communications infrastructure from Trilliant. By the end of 2010, the system will serve 1.3 million customers in the province of Ontario. The initiative won the "Best AMR Initiative in North America" award from the Utility Planning Network.[12]
The City of Mannheim in Germany is using realtime Broadband Powerline (BPL) communications in its Model City Mannheim "MoMa" project[13]
InovGrid is an innovative project in Evora that aims to equip the electricity grid with information and devices to automate grid management, improve service quality, reduce operating costs, promote energy efficiency and environmental sustainability, and increase the penetration of renewable energies and electric vehicles. It will be possible to control and manage the state of the entire electricity distribution grid at any given instant, allowing suppliers and energy services companies to use this technological platform to offer consumers information and added-value energy products and services. This project to install an intelligent energy grid places Portugal and EDP at the cutting edge of technological innovation and service provision in Europe.[14][15]
Goals of the smart grid
Respond to many conditions in supply and demand
Latency of the data flow is a major concern, with some early smart meter architectures allowing actually as long as 24 hours delay in receiving the data, preventing any possible reaction by either supplying or demanding devices.[16]
Smart energy demand
Smart energy demand describes the energy user component of the smart grid. It goes beyond and means much more than even energy efficiency and demand response combined. Smart energy demand is what delivers the majority of smart meter and smart grid benefits.
Smart energy demand is a broad concept. It includes any energy-user actions to:
- Enhancement of reliability
- reduce peak demand,
- shift usage to off-peak hours,
- lower total energy consumption,
- actively manage electric vehicle charging,
- actively manage other usage to respond to solar, wind, and other renewable resources
- buy more efficient appliances and equipment over time based on a better understanding of how energy is used by each appliance or item of equipment.
All of these actions minimize adverse impacts on electricity grids and maximize utility and, as a result, consumer savings.
Smart Energy Demand mechanisms and tactics include:
- smart meters,
- dynamic pricing,
- smart thermostats and smart appliances,
- automated control of equipment,
- real-time and next day energy information feedback to electricity users,
- usage by appliance data
- scheduling and control of loads such as electric vehicle chargers, home area networks (HANs), and others.
Provision megabits, control power with kilobits, sell the rest
The amount of data required to perform monitoring and switching your appliances off automatically is very small compared with that already reaching even remote homes to support voice, security, Internet and TV services. Many smart grid bandwidth upgrades are paid for by over-provisioning to also support consumer services, and subsidizing the communications with energy-related services or subsidizing the energy-related services, such as higher rates during peak hours, with communications. This is particularly true where governments run both sets of services as a public monopoly, e.g. in India. Because power and communications companies are generally separate commercial enterprises in North America and Europe, it has required considerable government and large-vendor effort to encourage various enterprises to cooperate. Some, like Cisco, see opportunity in providing devices to consumers very similar to those they have long been providing to industry.[17] Others, such as Silver Spring Networks[18] or Google,[19][20] are data integrators rather than vendors of equipment. While the AC power control standards suggest powerline networking would be the primary means of communication among smart grid and home devices, the bits may not reach the home via Broadband over Power Lines (BPL) initially but by fixed wireless. This may be only an interim solution, however, as separate power and data connections defeats full control.
Scale and scope
Europe's SuperSmart Grid, as well as earlier proposals (such as Al Gore's continental Unified Smart Grid) make semantic distinctions between local and national grids that sometimes conflict. Papers[21] by Battaglini et al. associate the term "smart grid" with local clusters (page 6), whereas the intelligent interconnecting backbone provides an additional layer of coordination above the local smart grids. Media use in both Europe and the US however tends to conflate national and local.
Regardless of terminology used, smart grid projects always intend to allow the continental and national interconnection backbones to fail without causing local smart grids to fail. As in the case of existing utility infrastructure, they would have to be able to function independently and ration whatever power is available to critical needs.
Municipal grid
Before recent standards efforts, municipal governments, for example in Miami, Florida,[22] have historically taken the lead in enforcing integration standards for smart grids/meters. As municipalities or municipal electricity monopolies also often own some fiber optic backbones and control transit exchanges at which communication service providers meet, they are often well positioned to force good integration.
Municipalities also have primary responsibility for emergency response and resilience, and would in most cases have the legal mandate to ration or provision power, say to ensure that hospitals and fire response and shelters have priority and receive whatever power is still available in a general outage.
Home area network
A home area network, or "home grid", extends some of these capabilities into the home using powerline networking and/or RF using standards such as ZigBee, INSTEON, Zwave, WiFi or others. In the smart grid, NIST is promoting interoperability between the different standards. OSHAN[23] is one initiative that enables interoperability in the home.
Because of the communication standards both smart power grids and some home area networks support more bandwidth than is required for power control and therefore may cost more than required. The existing 802.11 home networks generally have megabits of additional bandwidth for other services (burglary, fire, medical and environmental sensors and alarms, ULC and CCTV monitoring, access control and keying systems, intercoms and secure phone line services), and furthermore can't be separated from LAN and voice over IP networking, nor from TV once the IPTV standards have emerged.
A number of companies have entered the home area network space, such as Plug Smart, a brand of Juice Technologies, LLC, Tendril, Control4, and EnergyHub.
Consumer electronics devices now consume over half the power in a typical US home. Accordingly, the ability to shut down or hibernate devices when they are not receiving data could be a major factor in cutting energy use, but this would mean the electric company has information on whether a consumer is using their computer or not.
Other key devices that could aide in the utilities efforts to shed load during times of peak demand include air conditioning units, electric water heaters, pool pumps and other high wattage devices. In 2009, smart grid companies may represent one of the biggest and fastest growing sectors in the "cleantech" market.[24] It consistently receives more than half the venture capital investment.
In 2009 President Barack Obama asked the United States Congress "to act without delay" to pass legislation that included doubling alternative energy production in the next three years and building a new electricity "smart grid".[25] On April 13, 2009, George W. Arnold was named the first National Coordinator for Smart Grid Interoperability.
What a smart grid is
An electrical grid is not a single entity but an aggregate of multiple networks and multiple power generation companies with multiple operators employing varying levels of communication and coordination, most of which is manually controlled. Smart grids increase the connectivity, automation and coordination between these suppliers, consumers and networks that perform either long distance transmission or local distribution tasks.
- Transmission networks move electricity in bulk over medium to long distances, are actively managed, and generally operate from 345kV to 800kV over AC and DC lines.
- Local networks traditionally moved power in one direction, "distributing" the bulk power to consumers and businesses via lines operating at 132kV and lower.
This paradigm is changing as businesses and homes begin generating more wind and solar electricity, enabling them to sell surplus energy back to their utilities. Modernization is necessary for energy consumption efficiency, real time management of power flows and to provide the bi-directional metering needed to compensate local producers of power. Although transmission networks are already controlled in real time, many in the US and European countries are antiquated[26] by world standards, and unable to handle modern challenges such as those posed by the intermittent nature of alternative electricity generation, or continental scale bulk energy transmission.
Modernizes both transmission and distribution
A smart grid is an umbrella term that covers modernization of both the transmission and distribution grids. The modernization is directed at a disparate set of goals including facilitating greater competition between providers, enabling greater use of variable energy sources, establishing the automation and monitoring capabilities needed for bulk transmission at cross continent distances, and enabling the use of market forces to drive energy conservation.
Many smart grid features readily apparent to consumers such as smart meters serve the energy efficiency goal. The approach is to make it possible for energy suppliers to charge variable electric rates so that charges would reflect the large differences in cost of generating electricity during peak or off peak periods. Such capabilities allow load control switches to control large energy consuming devices such as water heaters so that they consume electricity when it is cheaper to produce.
Peak curtailment/leveling and time of use pricing
To reduce demand during the high cost peak usage periods, communications and metering technologies inform smart devices in the home and business when energy demand is high and track how much electricity is used and when it is used. It also gives utility companies the ability to reduce consumption by communicating to devices directly in order to prevent system overloads. An example would be a utility reducing the usage of a group of electric vehicle charging stations. To motivate them to cut back use and perform what is called peak curtailment or peak leveling, prices of electricity are increased during high demand periods, and decreased during low demand periods. It is thought that consumers and businesses will tend to consume less during high demand periods if it is possible for consumers and consumer devices to be aware of the high price premium for using electricity at peak periods. This could mean making trade-offs such as cooking dinner at 9 pm instead of 5 pm. When businesses and consumers see a direct economic benefit of using energy at off-peak times become more energy efficient, the theory is that they will include energy cost of operation into their consumer device and building construction decisions. See Time of day metering and demand response.
According to proponents of smart grid plans,[who?] this will reduce the amount of spinning reserve that electric utilities have to keep on stand-by, as the load curve will level itself through a combination of "invisible hand" free-market capitalism and central control of a large number of devices by power management services that pay consumers a portion of the peak power saved by turning their devices off.
Platform for advanced services
As with other industries, use of robust two-way communications, advanced sensors, and distributed computing technology will improve the efficiency, reliability and safety of power delivery and use. It also opens up the potential for entirely new services or improvements on existing ones, such as fire monitoring and alarms that can shut off power, make phone calls to emergency services, etc.
US and UK savings estimates and concerns
One United States Department of Energy study calculated that internal modernization of US grids with smart grid capabilities would save between 46 and 117 billion dollars over the next 20 years.[27] As well as these industrial modernization benefits, smart grid features could expand energy efficiency beyond the grid into the home by coordinating low priority home devices such as water heaters so that their use of power takes advantage of the most desirable energy sources. Smart grids can also coordinate the production of power from large numbers of small power producers such as owners of rooftop solar panels — an arrangement that would otherwise prove problematic for power systems operators at local utilities.
One important question is whether consumers will act in response to market signals. In the UK, where consumers have for nearly 10 years had a choice in the company from which they purchase electricity, more than 80% have stayed with their existing supplier, despite the fact that there are significant differences in the prices offered by a given electricity supplier.[citation needed]
Another concern is that the cost of telecommunications to fully support smart grids may be prohibitive. A less expensive communication mechanism is proposed[citation needed] using a form of "dynamic demand management" where devices shave peaks by shifting their loads in reaction to grid frequency. Grid frequency could be used to communicate load information without the need of an additional telecommunication network, but it would not support economic bargaining or quantification of contributions.
Although there are specific and proven smart grid technologies in use, smart grid is an aggregate term for a set of related technologies on which a specification is generally agreed, rather than a name for a specific technology. Some of the benefits of such a modernized electricity network include the ability to reduce power consumption at the consumer side during peak hours, called demand side management; enabling grid connection of distributed generation power (with photovoltaic arrays, small wind turbines, micro hydro, or even combined heat power generators in buildings); incorporating grid energy storage for distributed generation load balancing; and eliminating or containing failures such as widespread power grid cascading failures. The increased efficiency and reliability of the smart grid is expected to save consumers money and help reduce CO2 emissions.[28]
Problem definition
The major driving forces to modernize current power grids can be divided in four, general categories.
- Increasing reliability, efficiency and safety of the power grid.
- Enabling decentralized power generation so homes can be both an energy client and supplier (provide consumers with an interactive tool to manage energy usage, as net metering).
- Flexibility of power consumption at the clients side to allow supplier selection (enables distributed generation, solar, wind, biomass).
- Increase GDP by creating more new, green-collar energy jobs related to renewable energy industry manufacturing, plug-in electric vehicles, solar panel and wind turbine generation, energy conservation construction.[29][30]
Smart grid functions
Before examining particular technologies, a proposal can be understood in terms of what it is being required to do. The governments and utilities funding development of grid modernization have defined the functions required for smart grids. According to the United States Department of Energy's Modern Grid Initiative report,[30] a modern smart grid must:
- Be able to heal itself
- Motivate consumers to actively participate in operations of the grid
- Resist attack
- Provide higher quality power that will save money wasted from outages
- Accommodate all generation and storage options
- Enable electricity markets to flourish
- Run more efficiently
- Enable higher penetration of intermittent power generation sources
Self-healing
Using real-time information from embedded sensors and automated controls to anticipate, detect, and respond to system problems, a smart grid can automatically avoid or mitigate power outages, power quality problems, and service disruptions.[citation needed] Technology such as Fault Detection Isolation and Restoration (FDIRTM) can be used in conjunction with protective relays to automatically detect and isolate a fault, and then restore power to as many customers as possible. This will greatly improve the reliability of the electrical distribution network.
As applied to distribution networks, there is no such thing as a "self healing" network. If there is a failure of an overhead power line, given that these tend to operate on a radial basis (for the most part) there is an inevitable loss of power. In the case of urban/city networks that for the most part are fed using underground cables, networks can be designed (through the use of interconnected topologies) such that failure of one part of the network will result in no loss of supply to end users. A fine example of an interconnected network using zoned protection is that of the Merseyside and North Wales Electricity Board (MANWEB).
It is envisioned that the smart grid will likely have a control system that analyzes its performance using distributed, autonomous reinforcement learning controllers that have learned successful strategies to govern the behavior of the grid in the face of an ever changing environment such as equipment failures. Such a system might be used to control electronic switches that are tied to multiple substations with varying costs of generation and reliability.[31]
Consumer participation
A smart grid is a means for consumers to change their behavior around variable electric rates or participate in pricing programs designed to ensure reliable electrical service during high-demand conditions. Historically, the intelligence of the grid in North America has been demonstrated by the utilities operating it in the spirit of public service and shared responsibility, ensuring constant availability of electricity at a constant price, day in and day out, in the face of any and all hazards and changing conditions. A smart grid incorporates consumer equipment and behavior in grid design, operation, and communication. This enables consumers to better control “smart appliances” and “intelligent equipment” in homes and businesses, interconnecting energy management systems in “smart buildings” and enabling consumers to better manage energy use and reduce energy costs. Advanced communications capabilities equip customers with tools to take advantage of real-time electricity pricing, incentive-based load reduction signals, or emergency load reduction signals.
There is marketing evidence of consumer demand for greater choice. A survey conducted in the summer of 2007 interviewed almost 100 utility executives and sought the opinions of 1,900 households and small businesses from the U.S., Germany, Netherlands, England, Japan and Australia.[32] Among the findings:
- 83% of those who cannot yet choose their utility provider would welcome that option
- Roughly two-thirds of the customers that do not yet have renewable power options would like the choice
- Almost two-thirds are interested in operating their own generation, provided they can sell power back to the utility
And as already noted, in the UK where the experiment has been running longest, 80% have not changed their utility provider when given the choice (source: National Grid).
Proponents assert that the real-time, two-way communications available in a smart grid will enable consumers to be compensated for their efforts to save energy and to sell energy back to the grid through net-metering. By enabling distributed generation resources like residential solar panels, small wind and plug-in hybrid, proponents assert that the smart grid will spark a revolution in the energy industry by allowing small players like individual homes and small businesses to sell power to their neighbors or back to the grid. Many utilities currently promote small independent distributed generation and successfully integrate it with no impact. These sources of power are currently cost-effective with the help government subsidies that are available to help consumers purchase the often expensive equipment that is required.
The same will hold true for larger commercial businesses that have renewable or back-up power systems that can provide power for a price during peak demand events, typically in the summer when air condition units place a strain on the grid. This participation by smaller entities has been called the "democratization of energy"[citation needed]—it is similar to former Vice President Al Gore's vision for a Unified Smart Grid.
Resist attack
Smart grid technologies better identify and respond to man-made or natural disruptions. Real-time information enables grid operators to isolate affected areas and redirect power flows around damaged facilities.
One of the most important issues of resist attack is the smart monitoring of power grids, which is the basis of control and management of smart grids to avoid or mitigate the system-wide disruptions like blackouts. The traditional monitoring is based on weighted least square (WLS) which is very weak and prone to fail when gross errors (including topology errors, measurement errors or parameter errors) are present. New technology of state monitor is needed to achieve the goals of the smart grids.
High quality power
Outages and power quality issues cost US businesses more than $100 billion on average each year.[33] It is asserted that assuring more stable power provided by smart grid technologies will reduce downtime and prevent such high losses, but the reliability of complex systems is very difficult to analyze and guarantee. A more practical approach to improving reliability and power quality is to simply follow the well established and well documented engineering principles developed by federal agencies like the USDA's Rural Utility Service.[neutrality is disputed].
Accommodate generation options
As smart grids continue to support traditional power loads they also seamlessly interconnect fuel cells, renewables, microturbines, and other distributed generation technologies at local and regional levels. Integration of small-scale, localized, or on-site power generation allows residential, commercial, and industrial customers to self-generate and sell excess power to the grid with minimal technical or regulatory barriers. This also improves reliability and power quality, reduces electricity costs, and offers more customer choice. It will be a long time before a smart grid is actually necessary to realize these benefits. The existing grid can typically accommodate an order of magnitude more than the existing small-scale localized generation without the benefit of the smart grid. Most obstacles to the integration of larger renewable projects, like wind farms, is due to limitations of traditional infrastructure.
Enable electricity market
Significant increases in bulk transmission capacity will require construction of new transmission lines before improvements in transmission grid management proposed by smart grids can make a difference. Such improvements are aimed at creating an open marketplace where alternative energy sources from geographically distant locations can easily be sold to customers wherever they are located.
Intelligence in distribution grids are not required to enable small producers to generate and sell electricity at the local level using alternative sources such as rooftop-mounted photo voltaic panels, small-scale wind turbines, and micro hydro generators. For example Chelan PUD's SNAP program promotes distributed, consumer owned small scale generation. Only after very high penetration of these types of resources is additional intelligence provided by sensors and software designed to react instantaneously to imbalances caused by intermittent sources, such as distributed generation, necessary.
Optimize assets
A smart grid can optimize capital assets while minimizing operations and maintenance costs. Optimized power flows reduce waste and maximize use of lowest-cost generation resources. Harmonizing local distribution with inter-regional energy flows and transmission traffic improves use of existing grid assets and reduces grid congestion and bottlenecks, which can ultimately produce consumer savings.
Enable high penetration of intermittent generation sources
Climate change and environmental concerns will increase the amount of renewable energy resources. These are for the most part intermittent in nature. Smart Grid technologies will enable power systems to operate with larger amounts of such energy resources since they enable both the suppliers and consumers to compensate for such intermittency.
Features
Existing and planned implementations of smart grids provide a wide range of features to perform the required functions.
Load adjustment
The total load connected to the power grid can vary significantly over time. Although the total load is the sum of many individual choices of the clients, the overall load is not a stable, slow varying, average power consumption. Imagine the increment of the load if a popular television program starts and millions of televisions will draw current instantly. Traditionally, to respond to a rapid increase in power consumption, faster than the start-up time of a large generator, some spare generators are put on a dissipative standby mode[citation needed]. A smart grid may warn all individual television sets, or another larger customer, to reduce the load temporarily (to allow time to start up a larger generator) or continuously (in the case of limited resources). Using mathematical prediction algorithms it is possible to predict how many standby generators need to be used, to reach a certain failure rate. In the traditional grid, the failure rate can only be reduced at the cost of more standby generators. In a smart grid, the load reduction by even a small portion of the clients may eliminate the problem.
Demand response support
Demand response support allows generators and loads to interact in an automated fashion in real time, coordinating demand to flatten spikes. Eliminating the fraction of demand that occurs in these spikes eliminates the cost of adding reserve generators, cuts wear and tear and extends the life of equipment, and allows users to cut their energy bills by telling low priority devices to use energy only when it is cheapest.[34]
Currently, power grid systems have varying degrees of communication within control systems for their high value assets, such as in generating plants, transmission lines, substations and major energy users. In general information flows one way, from the users and the loads they control back to the utilities. The utilities attempt to meet the demand and succeed or fail to varying degrees (brownout, rolling blackout, uncontrolled blackout). The total amount of power demand by the users can have a very wide probability distribution which requires spare generating plants in standby mode to respond to the rapidly changing power usage. This one-way flow of information is expensive; the last 10% of generating capacity may be required as little as 1% of the time, and brownouts and outages can be costly to consumers.
Greater resilience to loading
Although multiple routes are touted as a feature of the smart grid, the old grid also featured multiple routes. Initial power lines in the grid were built using a radial model, later connectivity was guaranteed via multiple routes, referred to as a network structure. However, this created a new problem: if the current flow or related effects across the network exceed the limits of any particular network element, it could fail, and the current would be shunted to other network elements, which eventually may fail also, causing a domino effect. See power outage. A technique to prevent this is load shedding by rolling blackout or voltage reduction (brownout). [citation needed]
Decentralization of power generation
Another element of fault tolerance of traditional and smart grids is decentralized power generation. Distributed generation allows individual consumers to generate power onsite, using whatever generation method they find appropriate. This allows individual loads to tailor their generation directly to their load, making them independent from grid power failures. Classic grids were designed for one-way flow of electricity, but if a local sub-network generates more power than it is consuming, the reverse flow can raise safety and reliability issues. A smart grid can manage these situations, but utilities routinely manage this type of situation in the existing grid.[citation needed]
Price signaling to consumers
In many countries, including Belgium, Greece, the Netherlands and the UK, the electric utilities have installed double tariff electricity meters in many homes to encourage people to use their electric power during night time or weekends, when the overall demand from industry is very low. During off-peak time the price is reduced significantly, primarily for heating storage radiators or heat pumps with a high thermal mass, but also for domestic appliances. This idea will be further explored in a smart grid, where the price could be changing in seconds and electric equipment is given methods to react on that.
Technology
The bulk of smart grid technologies are already used in other applications such as manufacturing and telecommunications and are being adapted for use in grid operations. In general, smart grid technology can be grouped into five key areas:[35]
Integrated communications
Some communications are up to date, but are not uniform because they have been developed in an incremental fashion and not fully integrated. In most cases, data is being collected via modem rather than direct network connection. Areas for improvement include: substation automation, demand response, distribution automation, supervisory control and data acquisition (SCADA), energy management systems, wireless mesh networks and other technologies, power-line carrier communications, and fiber-optics. Integrated communications will allow for real-time control, information and data exchange to optimize system reliability, asset utilization, and security.
Sensing and measurement
Core duties are evaluating congestion and grid stability, monitoring equipment health, energy theft prevention, and control strategies support. Technologies include: advanced microprocessor meters (smart meter) and meter reading equipment, wide-area monitoring systems, dynamic line rating (typically based on online readings by Distributed temperature sensing combined with Real time thermal rating (RTTR) systems), electromagnetic signature measurement/analysis, time-of-use and real-time pricing tools, advanced switches and cables, backscatter radio technology, and Digital protective relays.
Smart meters
A smart grid replaces analog mechanical meters with digital meters that record usage in real time. Smart meters are similar to Advanced Metering Infrastructure meters and provide a communication path extending from generation plants to electrical outlets (smart socket) and other smart grid-enabled devices. By customer option, such devices can shut down during times of peak demand.[citation needed]
Phasor measurement units
High speed sensors called PMUs distributed throughout their network can be used to monitor power quality and in some cases respond automatically to them. Phasors are representations of the waveforms of alternating current, which ideally in real-time, are identical everywhere on the network and conform to the most desirable shape. In the 1980s, it was realized that the clock pulses from global positioning system (GPS) satellites could be used for very precise time measurements in the grid. With large numbers of PMUs and the ability to compare shapes from alternating current readings everywhere on the grid, research suggests that automated systems will be able to revolutionize the management of power systems by responding to system conditions in a rapid, dynamic fashion.[36]
A wide-area measurement system (WAMS) is a network of PMUS that can provide real-time monitoring on a regional and national scale. Many in the power systems engineering community believe that the Northeast blackout of 2003 would have been contained to a much smaller area if a wide area phasor measurement network was in place.[37]
Advanced components
Innovations in superconductivity, fault tolerance, storage, power electronics, and diagnostics components are changing fundamental abilities and characteristics of grids. Technologies within these broad R&D categories include: flexible alternating current transmission system devices, high voltage direct current, first and second generation superconducting wire, high temperature superconducting cable, distributed energy generation and storage devices, composite conductors, and “intelligent” appliances.[citation needed]
Advanced control
Power system automation enables rapid diagnosis of and precise solutions to specific grid disruptions or outages. These technologies rely on and contribute to each of the other four key areas. Three technology categories for advanced control methods are: distributed intelligent agents (control systems), analytical tools (software algorithms and high-speed computers), and operational applications (SCADA, substation automation, demand response, etc.). Using artificial intelligence programming techniques, Fujian power grid in China created a wide area protection system that is rapidly able to accurately calculate a control strategy and execute it.[38] The Voltage Stability Monitoring & Control (VSMC) software uses a sensitivity-based successive linear programming method to reliably determine the optimal control solution.[39]
Improved interfaces and decision support
Information systems that reduce complexity so that operators and managers have tools to effectively and efficiently operate a grid with an increasing number of variables. Technologies include visualization techniques that reduce large quantities of data into easily understood visual formats, software systems that provide multiple options when systems operator actions are required, and simulators for operational training and “what-if” analysis.
Standards and groups
IEC TC57 has created a family of international standards that can be used as part of the smart grid. These standards include IEC61850 which is an architecture for substation automation, and IEC 61970/61968 – the Common Information Model (CIM). The CIM provides for common semantics to be used for turning data into information.
MultiSpeak has created a specification that supports distribution functionality of the smart grid. MultiSpeak has a robust set of integration definitions that supports nearly all of the software interfaces necessary for a distribution utility or for the distribution portion of a vertically integrated utility. MultiSpeak integration is defined using extensible markup language (XML) and web services.
The IEEE has created a standard to support synchrophasors – C37.118.
The UCA International User Group discusses and supports real world experience of the standards used in smart grids.
A utility task group within LonMark International deals with smart grid related issues.
There is a growing trend towards the use of TCP/IP technology as a common communication platform for smart meter applications, so that utilities can deploy multiple communication systems, while using IP technology as a common management platform.[40][41]
IEEE P2030 is an IEEE project developing a "Draft Guide for Smart Grid Interoperability of Energy Technology and Information Technology Operation with the Electric Power System (EPS), and End-Use Applications and Loads".[42][43]
NIST has included ITU-T G.hn as one of the "Standards Identified for Implementation" for the Smart Grid "for which it believed there was strong stakeholder consensus".[44] G.hn is standard for high-speed communications over power lines, phone lines and coaxial cables.
OASIS EnergyInterop' – is an OASIS technical committee developing XML standards for energy interoperation. It's starting point is the California OpenADR standard.
Under the Energy Independence and Security Act of 2007 (EISA), NIST is charged with overseeing the identification and selection of hundreds of standards that will be required to implement the Smart Grid in the U.S. These standards will be referred by NIST to the Federal Energy Regulatory Commission (FERC). This work has begun, and the first standards have already been selected for inclusion in NIST’s Smart Grid catalog.[45] However, some commentators have suggested that the benefits that could be realized from Smart Grid standardization could be threatened by a growing number of patents that cover Smart Grid architecture and technologies.[46] If patents that cover standardized Smart Grid elements are not revealed until technology is broadly distributed throughout the network (“locked-in”), significant disruption could occur when patent holders seek to collect unanticipated rents from large segments of the market.
Smart power generation
Smart power generation is a concept of matching electricity production with demand using multiple identical generators which can start, stop and operate efficiently at chosen load, independently of the others, making them suitable for base load and peaking power generation.[47] Matching supply and demand, called load balancing, is essential for a stable and reliable supply of electricity. Short-term deviations in the balance lead to frequency variations and a prolonged mismatch results in blackouts. Operators of power transmission systems are charged with the balancing task, matching the power output of the all the generators to the load of their electrical grid. The load balancing task has become much more challenging as increasingly intermittent and variable generators such as wind turbines and solar cells are added to the grid, forcing other producers to adapt their output much more frequently than has been required in the past.
First two dynamic grid stability power plants utilizing the concept has been ordered by Elering and will be built by Wärtsilä in Kiisa, Estonia. Their purpose is to "provide dynamic generation capacity to meet sudden and unexpected drops in the electricity supply." They are scheduled to be ready during 2013 and 2014, and their total output will be 250 MW.[48]
Recent studies
Many different concepts have been used to model intelligent power grids. They are generally studied within the framework of complex systems. In a recent brainstorming session,[49] the power grid was considered within the context of optimal control, ecology, human cognition, glassy dynamics, information theory, microphysics of clouds, and many others. Here is a selection of the types of analyses that have appeared in recent years.
- Protection systems that verify and supervise themselves
Pelqim Spahiu and Ian R. Evans in their study introduced the concept of a substation based smart protection and hybrid Inspection Unit.[50][51]
- Kuramoto oscillators
The Kuramoto model is a well-studied system. The power grid has been described in this context as well.[52][53] The goal is to keep the system in balance, and/or to maintain phase synchronization (also known as phase locking). Non-uniform oscillators also help to model different technologies, different types of power generators, patterns of consumption, and so on. The model has also been used to describe the synchronization patterns in the blinking of fireflies.[52]
- Bio-systems
Power grids have been related to complex biological systems in many other contexts. In one study, power grids were compared to the dolphin social network.[54] These creatures streamline and/or intensify communication in case of an unusual situation. The intercommunications that enable them to survive are highly complex.
- Random fuse networks
In percolation theory, random fuse networks have been studied. The current density might be too low in some areas, and too strong in others. The analysis can therefore be used to smooth out potential problems in the network. For instance, high-speed computer analysis can predict blown fuses and correct for them, or analyze patterns that might lead to a power outage.[55] It is difficult for humans to predict the long term patterns in complex networks, so fuse and/or diode networks are used instead.
- Neural networks
Neural networks have been considered for power grid management as well. The references are too numerous to list.[56][57][58][59]
- Markov processes
As wind power continues to gain popularity, it becomes a necessary ingredient in realistic power grid studies. Off-line storage, wind variability, supply, demand, pricing, and other factors can be modelled as a mathematical game. Here the goal is to develop a winning strategy. Markov processes have been used to model and study this type of system.[60]
- Maximum entropy
All of these methods are, in one way or another, maximum entropy methods, which is an active area of research.[61][62] This goes back to the ideas of Shannon, and many other researchers who studied communication networks. Continuing along similar lines today, modern wireless network research often considers the problem of network congestion,[63] and many algorithms are being proposed to minimize it, including game theory,[64] innovative combinations of FDMA, TDMA, and others.
Obstacles
In Europe and the US, significant impediments exist to the widespread adoption of smart grid technologies, including:
- regulatory environments that don't reward utilities for operational efficiency, excluding U.S. awards.
- consumer concerns over privacy,
- social concerns over "fair" availability of electricity,
- social concerns over Enron style abuses of information leverage,
- limited ability of utilities to rapidly transform their business and operational environment to take advantage of smart grid technologies.
- concerns over giving the government mechanisms to control the use of all power using activities.
Before a utility installs an advanced metering system, or any type of smart system, it must make a business case for the investment. Some components, like the power system stabilizers (PSS)[clarification needed] installed on generators are very expensive, require complex integration in the grid's control system, are needed only during emergencies, but are only effective if other suppliers on the network have them. Without any incentive to install them, power suppliers don't.[9] Most utilities find it difficult to justify installing a communications infrastructure for a single application (e.g. meter reading). Because of this, a utility must typically identify several applications that will use the same communications infrastructure – for example, reading a meter, monitoring power quality, remote connection and disconnection of customers, enabling demand response, etc. Ideally, the communications infrastructure will not only support near-term applications, but unanticipated applications that will arise in the future. Regulatory or legislative actions can also drive utilities to implement pieces of a smart grid puzzle. Each utility has a unique set of business, regulatory, and legislative drivers that guide its investments. This means that each utility will take a different path to creating their smart grid and that different utilities will create smart grids at different adoption rates.
Some features of smart grids draw opposition from industries that currently are, or hope to provide similar services. An example is competition with cable and DSL Internet providers from broadband over powerline internet access. Providers of SCADA control systems for grids have intentionally designed proprietary hardware, protocols and software so that they cannot inter-operate with other systems in order to tie its customers to the vendor.[9]
Market outlook
In 2009, the US smart grid industry was valued at about $21.4 billion – by 2014, it will exceed at least $42.8 billion. Given the success of the smart grids in the U.S., the world market is expected to grow at a faster rate, surging from $69.3 billion in 2009 to $171.4 billion by 2014. With the segments set to benefit the most will be smart metering hardware sellers and makers of software used to transmit and organize the massive amount of data collected by meters.[65]
Deployments and deployment attempts
In the so called E-Energy projects several German utilities are creating first nucleolus in six independent model regions. A technology competition identified this model regions to carry out research and development activities with the main objective to create an "Internet of Energy"[66]
One of the first attempted deployments of "smart grid" technologies in the United States was rejected in 2009 by electricity regulators in the Commonwealth of Massachusetts, a US state.[67] According to an article in the Boston Globe, Northeast Utilities' Western Massachusetts Electric Co. subsidiary actually attempted to create a "smart grid" program using public subsidies that would switch low income customers from post-pay to pre-pay billing (using "smart cards") in addition to special hiked "premium" rates for electricity used above a predetermined amount.[67] This plan was rejected by regulators as it "eroded important protections for low-income customers against shutoffs".[67] According to the Boston Globe, the plan "unfairly targeted low-income customers and circumvented Massachusetts laws meant to help struggling consumers keep the lights on".[67] A spokesman for an environmental group supportive of smart grid plans and Western Massachusetts' Electric's aforementioned "smart grid" plan, in particular, stated "If used properly, smart grid technology has a lot of potential for reducing peak demand, which would allow us to shut down some of the oldest, dirtiest power plants... It’s a tool."[67]
In the Netherlands a large scale project (>5000 connections, >20 partners) was initiated to demonstrate integrated smart grids technologies, services and business cases.[68]
General economics developments
As customers can choose their electricity suppliers, depending on their different tariff methods, the focus of transportation costs will be increased. Reduction of maintenance and replacements costs will stimulate more advanced control.
A smart grid precisely limits electrical power down to the residential level, network small-scale distributed energy generation and storage devices, communicate information on operating status and needs, collect information on prices and grid conditions, and move the grid beyond central control to a collaborative network.[37]
Guidelines and standards
IEEE 2030.2 represents an extension of the work aimed at utility storage systems for transmission and distribution networks. The IEEE P2030 group expects to deliver early 2011 an overarching set of guidelines on smart grid interfaces. The new guidelines will cover areas including batteries and supercapacitors as well as flywheels. the group has also spun out a 2030.1 effort drafting guidelines for integrating electric vehicles into the smart grid.
See also
References
- ^ "Smart Grids European Technology Platform | www.smartgrids.eu". smartgrids.eu. 2011 [last update]≤. Retrieved October 11, 2011.
{{cite web}}
: Check date values in:|year=
(help)CS1 maint: year (link) - ^ unidirectional – Wiktionary. En.wiktionary.org. Retrieved on 2011-05-14.
- ^ [1]. The Regulatory Compact. Retrieved on 2011-05-19.
- ^
Smart Grid Working Group (2003-06). "Challenge and Opportunity: Charting a New Energy Future, Appendix A: Working Group Reports" (PDF). Energy Future Coalition. Retrieved 2008-11-27.
{{cite web}}
: Check date values in:|date=
(help) - ^ Gorman, Siobhan (2009-04-08). "Electricity Grid in U.S. Penetrated By Spies". The Wall Street Journal.
- ^ Federal Energy Regulatory Commission staff report (2006-08). "Assessment of Demand Response and Advanced Metering (Docket AD06-2-000)" (PDF). United States Department of Energy: 20. Retrieved 2008-11-27.
{{cite journal}}
: Check date values in:|date=
(help); Cite journal requires|journal=
(help) - ^ a b National Energy Technology Laboratory (2007-08). "NETL Modern Grid Initiative — Powering Our 21st-Century Economy" (PDF). United States Department of Energy Office of Electricity Delivery and Energy Reliability: 17. Retrieved 2008-12-06.
{{cite journal}}
: Check date values in:|date=
(help); Cite journal requires|journal=
(help) - ^ "Gridwise History: How did GridWise start?". Pacific Northwest National Laboratory. 2007-10-30. Archived from the original on 2008-10-27. Retrieved 2008-12-03.
- ^ a b c Qixun Yang, Board Chairman, Beijing Sifang Automation Co. Ltd., China and .Bi Tianshu, Professor, North China Electric Power University, China. (2001-06-24). "WAMS Implementation in China and the Challenges for Bulk Power System Protection" (PDF). Panel Session: Developments in Power Generation and Transmission — Infrastructures in China, IEEE 2007 General Meeting, Tampa, FL, USA, 24–28 June 2007 Electric Power, ABB Power T&D Company, and Tennessee Valley Authority. Institute of Electrical and Electronics Engineers. Retrieved 2008-12-01.
{{cite journal}}
: CS1 maint: multiple names: authors list (link) Cite error: The named reference "Yang" was defined multiple times with different content (see the help page). - ^ "Building for the future: Interview with Andres Carvallo, CIO — Austin Energy Utility". Next Generation Power and Energy (244). GDS Publishing Ltd.... Retrieved 2008-11-26.
- ^ Betsy Loeff (2008-03). "AMI Anatomy: Core Technologies in Advanced Metering". Ultrimetrics Newsletter. Automatic Meter Reading Association (Utilimetrics).
{{cite journal}}
: Check date values in:|date=
(help) - ^ Betsy Loeff, Demanding standards: Hydro One aims to leverage AMI via interoperability, PennWell Corporation
- ^ "E-Energy Project Model City Mannheim". MVV Energie. 2011 [last update]. Retrieved May 16, 2011.
{{cite web}}
: Check date values in:|year=
(help)CS1 maint: year (link) - ^ Évora InovCity - Smart Energy Living
- ^ Portuguese Smart City
- ^ Why the Smart Grid Won't Have the Innovations of the Internet Any Time Soon: Cleantech News and Analysis «. Earth2tech.com (2009-06-05). Retrieved on 2011-05-14.
- ^ Cisco's Latest Consumer Play: The Smart Grid: Cleantech News and Analysis «. Earth2tech.com Retrieved on 2011-05-14.
- ^ Silver Spring Networks: The Cisco of Smart Grid?: Cleantech News and Analysis «. Earth2tech.com (2008-05-01). Retrieved on 2011-05-14.
- ^ Utility Perspective: Why Partner With Google PowerMeter?: Cleantech News and Analysis «. Earth2tech.com (2009-05-20). Retrieved on 2011-05-14.
- ^ E-Commerce News: Deals: Utility Companies Plug In to Google PowerMeter. Ecommercetimes.com. Retrieved on 2011-05-14.
- ^ Supersmart grid paper
- ^ Smart Grid Miami: FPL, GE, Cisco, Silver Spring Rolling Out 1M Smart Meters: Cleantech News and Analysis «. Earth2tech.com (2009-04-20). Retrieved on 2011-05-14.
- ^ "Open Source Home Area Network (OSHAN) Initiative".
- ^ "The rise of the Smart Grid". Deloitte TMT Predictions. Archived from the original on 2010-07-29.
- ^ "Obama's Speech on the Economy". New York Times. 2009-01-09.
- ^ The Federal Energy Regulatory Commission Chairman Pat Wood, III (appointed by George Bush) stated that the US transmission system cannot afford to be "antiquated" in this news release Federal Energy Regulatory Commission (2002-09-18). "FERC news release on [[ISO]]" (PDF). ProQuest Dissertations and Theses; Thesis (PhD)--Duke University: 1. Bibcode:1997PhDT.......318S. Archived from the original (PDF) on 2009-01-17. Retrieved 2009-04-29.
{{cite journal}}
: URL–wikilink conflict (help) - ^ L. D. Kannberg (2003-11). "GridWise: The Benefits of a Transformed Energy System". Pacific Northwest National Laboratory under contract with the United States Department of Energy: 25. arXiv:nlin/0409035.
{{cite journal}}
:|format=
requires|url=
(help); Check|authorlink=
value (help); Check date values in:|date=
(help); Cite journal requires|journal=
(help); External link in
(help); Unknown parameter|authorlink=
|coauthors=
ignored (|author=
suggested) (help) - ^ Smart Grid and Renewable Energy Monitoring Systems, SpeakSolar.org 03rd September 2010
- ^ Smartgrids Advisory Council. "Driving Factors in the Move Towards Smartgrids". European Smartgrids Technology Platform: Vision and Strategy (PDF). European Commission. p. 9. ISBN 92-79-01414-5.
- ^ a b National Energy Technology Laboratory (2007-07-27). "A Vision for the Modern Grid" (PDF). United States Department of Energy: 5. Retrieved 2008-11-27.
{{cite journal}}
: Cite journal requires|journal=
(help) - ^ Anderson, Roger (2008 ISBN 978-1-59370-157-4). p 333. Computer-Aided Lean Management for the Energy Industry.
{{cite book}}
: Check date values in:|year=
(help); Unknown parameter|coauthors=
ignored (|author=
suggested) (help)CS1 maint: year (link) - ^ Energy and Utilities, 2007 IBM Global Residential/Small Business Consumer Survey
- ^ page 10
- ^ Energy Future Coalition, “Challenge and Opportunity: Charting a New Energy Future,” Appendix A: Working Group Reports, Report of the Smart Grid Working Group. http://web.archive.org/web/20080910051559/http://www.energyfuturecoalition.org/pubs/app_smart_grid.pdf
- ^ U.S. Department of Energy, National Energy Technology Laboratory, Modern Grid Initiative, http://www.netl.doe.gov/moderngrid/opportunity/vision_technologies.html
- ^ Yilu Liu, Lamine Mili, Jaime De La Ree, Reynaldo Francisco Nuqui, Reynaldo Francisco Nuqui (2001-07-12). "State Estimation and Voltage Security Monitoring Using Synchronized Phasor Measurement" (PDF). Research paper from work sponsored by American Electric Power, ABB Power T&D Company, and Tennessee Valley Authority. Virginia Polytechnic Institute and State University. Retrieved 2008-12-01.
"Simulations and field experiences suggest that PMUs can revolutionize the way power systems are monitored and controlled."
{{cite journal}}
: Unknown parameter|laysummary=
ignored (help)CS1 maint: multiple names: authors list (link) - ^ a b Patrick Mazza (2005-04-27). "Powering Up the Smart Grid: A Northwest Initiative for Job Creation, Energy Security, and Clean, Affordable Electricity" (doc). Climate Solutions: 7. Retrieved 2008-12-01.
{{cite journal}}
: Cite journal requires|journal=
(help) Cite error: The named reference "Mazza01" was defined multiple times with different content (see the help page). - ^ "Wide Area Protection System for Stability" (PDF). Nanjing Nari-Relays Electric Co., Ltd. 2008-04-22: 2. Archived from the original (PDF) on 2009-03-18. Retrieved 2008-12-12.
{{cite journal}}
: Cite journal requires|journal=
(help) Examples are given of two events, one stabilizing the system after a fault on a 1 gigawatt HVDC feed, with response timed in milliseconds. - ^ Zhao, Jinquan; Huang, Wenying; Fang, Zhaoxiong; Chen, Feng; Li, Kewen; Deng, Yong (2007-06-24). "2007 IEEE Power Engineering Society General Meeting". Proceedings, Power Engineering Society General Meeting, 2007. Tampa, FL, USA: IEEE: 1. doi:10.1109/PES.2007.385975. ISBN 1-4244-1296-X.
{{cite journal}}
:|chapter=
ignored (help);|format=
requires|url=
(help); Unknown parameter|laysummary=
ignored (help) - ^ Cisco Outlines Strategy for Highly Secure, 'Smart Grid' Infrastructure -> Cisco News. Newsroom.cisco.com (2009-05-18). Retrieved on 2011-05-14.
- ^ DS2 Blog: Why the Smart Grid must be based on IP standards. Blog.ds2.es (2009-05-20). Retrieved on 2011-05-14.
- ^ IEEE P2030 Official Website
- ^ IEEE, conference drive smart grids. Eetimes.com (2009-03-19). Retrieved on 2011-05-14.
- ^ Commerce Secretary Unveils Plan for Smart Grid Interoperability. Nist.gov. Retrieved on 2011-05-14.
- ^ SGIP Catalog of Standards
- ^ Jorge L. Contreras, "Gridlock or Greased Lightning: Intellectual Property, Government Involvement and the Smart Grid" (presented at American Intellectual Property Law Assn. (AIPLA) 2011 Annual Meeting (Oct. 2011, Washington D.C.)
- ^ Klimstra, Jakob; Hotakainen, Markus (2011). Smart Power Generation (PDF). Helsinki: Avain Publishers. ISBN 78-9-51692-846-6.
{{cite book}}
: Check|isbn=
value: length (help) - ^ Toomas Hõbemägi, Baltic Business News
- ^ Paul Bourgine; David Chavalarias; Edith Perrier; Frederic Amblard; Francois Arlabosse; Pierre Auger; Jean-Bernard Baillon; Olivier Barreteau; Pierre Baudot (2009). "French Roadmap for complex Systems 2008–2009". arXiv:0907.2221 [nlin.AO].
- ^ 1 Protection Systems that verify and supervise themselves, Pelqim Spahiu, Ian R. Evans – IEEE ISGT Innovative Smart Grid Technologies Europe 2011
- ^ 2 IED based Protection & Control equipment with Non-Standard primary system arrangements – An approach to application, Pelqim Spahiu, Namita Uppal – 10th IET International Conference on DPSP in Manchester, April 2010
- ^ a b Giovanni Filatrella; Arne Hejde Nielsen; Niels Falsig Pedersen (2008). "Analysis of a power grid using the Kuramoto-like model". European Physical Journal B. 61 (4): 485–491. arXiv:0705.1305. doi:10.1140/epjb/e2008-00098-8.
- ^ Florian Dorfler; Francesco Bullo (2009). "Synchronization and Transient Stability in Power Networks and Non-Uniform Kuramoto Oscillators". arXiv:0910.5673 [math.OC].
- ^ David Lusseau (2003). "The emergent properties of a dolphin social network". Proceedings of the Royal Society of London B. 270: S186–S188. arXiv:cond-mat/0307439. doi:10.1098/rsbl.2003.0057.
- ^ Olaf Stenull; Hans-Karl Janssen (2001). "Nonlinear random resistor diode networks and fractal dimensions of directed percolation clusters". Phys. Rev. E 6435 (2001). 64. arXiv:cond-mat/0104532. doi:10.1103/PhysRevE.64.016135.
- ^ Werbos (2006). "Using Adaptive Dynamic Programming to Understand and Replicate Brain Intelligence: the Next Level Design". arXiv:q-bio/0612045.
{{cite arXiv}}
:|class=
ignored (help) - ^ Claire Christensen; Reka Albert (2006). "Using graph concepts to understand the organization of complex systems". arXiv:q-bio.OT/0609036.
{{cite arXiv}}
:|class=
ignored (help) - ^ Vito Latora; Massimo Marchiori (2002). "Economic Small-World Behavior in Weighted Networks". European Physical Journal B. 32 (2): 249–263. arXiv:cond-mat/0204089. doi:10.1140/epjb/e2003-00095-5.
- ^ Vito Latora; Massimo Marchiori (2002). "The Architecture of Complex Systems". arXiv:cond-mat/0205649.
{{cite arXiv}}
:|class=
ignored (help) - ^ Miao He; Sugumar Murugesan; Junshan Zhang (2010). "Multiple Timescale Dispatch and Scheduling for Stochastic Reliability in Smart Grids with Wind Generation Integration". arXiv:1008.3932 [cs.SY].
- ^ Barreiro; Julijana Gjorgjieva; Fred Rieke; Eric Shea-Brown (2010). "When are feedforward microcircuits well-modeled by maximum entropy methods?". arXiv:1011.2797 [q-bio.NC].
- ^ Jianxin Chen; Zhengfeng Ji; Mary Beth Ruskai; Bei Zeng; Duanlu Zhou (2010). "Principle of Maximum Entropy and Ground Spaces of Local Hamiltonians". arXiv:1010.2739 [quant-ph].
- ^ Sahand Haji Ali Ahmad; Mingyan Liu; Yunnan Wu (2009). "Congestion games with resource reuse and applications in spectrum sharing". arXiv:0910.4214 [cs.GT].
- ^ Sahand Ahmad; Cem Tekin; Mingyan Liu; Richard Southwell; Jianwei Huang (2010). "Spectrum Sharing as Spatial Congestion Games". arXiv:1011.5384 [cs.GT].
- ^ "Report: Smart Grid Market Could Double in Four Years". Zpryme Smart Grid Market.
- ^ E-Energy: Startseite. E-energy.de. Retrieved on 2011-05-14.
- ^ a b c d e Massachusetts rejects utility's prepayment plan for low income customers, The Boston Globe, 2009-07-23
- ^ Smart Energy Collective. Smartenergycollective.nl. Retrieved on 2011-05-14.
External links
- IEEE SmartGrid Portal IEEE's collection of SmartGrid resources
- Smart Grids (European Commission)
- The NIST Smart Grid Collaboration Site NIST's public wiki for Smart Grid
- Video Lecture: Computer System Security: Technical and Social Challenges in Creating a Trustworthy Power Grid, University of Illinois at Urbana-Champaign
- Video Lecture: Smart Grid: Key to a Sustainable Energy Infrastructure, University of Illinois at Urbana-Champaign
- The IDEAS project (University of Southampton project developing agent-based mechanisms for the Smart Grid)
- Institute for Computational Sustainability
- Perspectives and priorities on RuggedCom Smart Grid Research IEC 61850 Technologies
- Projects with Smart Substation Solution
- Smart High Voltage Substation Based on IEC 61850 Process Bus and IEEE 1588 Time Synchronization
- Test and evaluation system for multi-protocol sampled value protection schemesby Dave Ingram