Jump to content

Boeing 777

From Wikipedia, the free encyclopedia

This is an old revision of this page, as edited by 77.186.6.240 (talk) at 08:07, 25 January 2014 (→Entry into service: exactly). The present address (URL) is a permanent link to this revision, which may differ significantly from the current revision.

Boeing 777
Aircraft landing approach. Front quarter view of twin-engine jet in flight with flaps and landing gear extended.
Boeing 777-200 of United Airlines, the 777's launch customer
Role Wide-body jet airliner
National origin United States
Manufacturer Boeing Commercial Airplanes
First flight June 12, 1994
Introduction June 7, 1995, with United Airlines
Status In service
Primary users Emirates
United Airlines
Air France
Singapore Airlines
Produced 1993–present
Number built 1,164 through December 2013[1]

The Boeing 777 is a family of long-range wide-body twin-engine jet airliners developed and manufactured by Boeing Commercial Airplanes. It is the world's largest twinjet and has a typical seating capacity for 314 to 451 passengers, with a range of 5,235 to 9,380 nautical miles (9,695 to 17,372 km). Commonly referred to as the "Triple Seven",[2][3] its distinguishing features include the largest-diameter turbofan engines of any aircraft, six wheels on each main landing gear, a circular fuselage cross-section, and a blade-shaped tail cone.[4] Developed in consultation with eight major airlines, the 777 was designed to replace older wide-body airliners and bridge the capacity difference between the 767 and 747. As Boeing's first fly-by-wire airliner, it has computer-mediated controls; it is also the first entirely computer-designed commercial aircraft.

As of 2013, the 777 is produced in two fuselage lengths. The original 777-200 variant entered commercial service in 1995, followed by the extended-range 777-200ER in 1997. The stretched 777-300, which is 33.3 ft (10.1 m) longer, entered service in 1998. The longer-range 777-300ER and 777-200LR variants entered service in 2004 and 2006 respectively, while a freighter version, the 777F, debuted in February 2009. Both longer-range versions and the freighter feature General Electric GE90 engines and extended raked wingtips. The earlier 777-200, −200ER and −300 versions are equipped with GE90, Pratt & Whitney PW4000 or Rolls-Royce Trent 800 engines. The 777-200LR is the world's longest-range airliner and can fly more than halfway around the globe; it holds the record for the longest distance flown non-stop by a commercial aircraft.[5][6] In November 2013, Boeing announced the development of upgraded 777-8X and 777-9X models featuring composite wings and GE9X engines.

United Airlines first placed the 777 into commercial airline service in June 1995. As of June 2013, 60 customers had placed orders for 1,452 aircraft of all variants, with 1,113 delivered.[1] The most common and successful variant is the 777-300ER with 452 delivered and over 700 orders as of December 2013.[1] Emirates operates the largest 777 fleet, with 127 passenger and freighter aircraft as of June 2013.[7] The airliner is rated as one of the safest aircraft based on its accident safety record and high number of flight hours.[8] The 777 has been involved in three hull-loss accidents as of July 2013; Asiana Airlines Flight 214 was the first fatal crash of the aircraft in 18 years of revenue service.

The 777 ranks as one of Boeing's best-selling models. Because of rising fuel costs, airlines have acquired the type as a comparatively fuel-efficient alternative to other wide-body jets and have increasingly deployed the aircraft on long-haul transoceanic routes. Direct market competitors include the Airbus A330-300, upcoming Airbus A350 XWB, and the out-of-production A340 and McDonnell Douglas MD-11. The 787 Dreamliner, which entered service in 2011, shares design features with the 777. The updated 777X, currently in development, further includes technologies used on the 787.

Development

Background

In the early 1970s, the Boeing 747, McDonnell Douglas DC-10, and the Lockheed L-1011 TriStar became the first generation of wide-body passenger airliners to enter service.[9] In 1978, Boeing unveiled three new models: the twin-engine Boeing 757 to replace its venerable 727, the twin-engine 767 to challenge the Airbus A300, and a trijet 777 concept to compete with the DC-10 and L-1011.[10][11][12] The mid-size 757 and 767 launched to market success, due in part to 1980s extended-range twin-engine operational performance standards (ETOPS) regulations governing transoceanic twinjet operations.[13] These regulations allowed twin-engine airliners to make ocean crossings at up to three hours' distance from emergency diversionary airports.[14] Under ETOPS rules, airlines began operating the 767 on long-distance overseas routes that did not require the capacity of larger airliners.[13] The trijet 777 was later dropped, following marketing studies that favored the 757 and 767 variants.[15] Boeing was left with a size and range gap in its product line between the 767-300ER and the 747-400.[16]

By the late 1980s, DC-10 and L-1011 models were approaching retirement age, prompting manufacturers to develop replacement designs.[17] McDonnell Douglas was working on the MD-11, a stretched and upgraded successor of the DC-10,[17] while Airbus was developing their A330 and A340.[17] In 1986, Boeing unveiled proposals for an enlarged 767, tentatively named 767-X,[18] to target the replacement market for first-generation wide-bodies like the DC-10,[14] and to complement existing 767 and 747 models in the company lineup.[19] The initial proposal featured a longer fuselage and larger wings than the existing 767,[18] along with winglets.[20] Later plans expanded the fuselage cross-section but retained the existing 767 flight deck, nose, and other elements.[18]

Airline customers were unimpressed with the 767-X proposals, and instead wanted an even wider fuselage cross-section, fully flexible interior configurations, short- to intercontinental-range capability, and an operating cost lower than any 767 stretch.[14] Airline planners' requirements for larger aircraft had become increasingly specific, adding to the heightened competition among aircraft manufacturers.[17] By 1988, Boeing realized that the only answer was a new design, which became the 777 twinjet.[21] The company opted for the twin-engine configuration given past design successes, projected engine developments, and reduced-cost benefits.[22] On December 8, 1989, Boeing began issuing offers to airlines for the 777.[18]

Design effort

A flight deck, from behind the two pilots' seats. A center console lies in between the seats, in front is an instrument panel with several displays, and light enters through the forward windows.
Glass cockpit of a Transaero Airlines 777-200ER

The design phase for Boeing's new twinjet was different from the company's previous commercial jetliners. For the first time, eight major airlines – All Nippon Airways, American Airlines, British Airways, Cathay Pacific Airways, Delta Air Lines, Japan Airlines, Qantas, and United Airlines – had a role in the development of the airliner.[23] This was a departure from industry practice, where manufacturers typically designed aircraft with minimal customer input.[11] The eight airlines that contributed to the design process became known within Boeing as the "Working Together" group.[23] At the first group meeting in January 1990, a 23-page questionnaire was distributed to the airlines, asking each what it wanted in the new design.[14] By March 1990, Boeing and the airlines had decided upon a basic design configuration: a cabin cross-section close to the 747's, capacity up to 325 passengers, flexible interiors, a glass cockpit, fly-by-wire controls, and 10 percent better seat-mile costs than the A330 and MD-11.[14] Boeing also selected its Everett factory in Washington, home of 747 production, as the final assembly site for the 777.[24]

On October 14, 1990, United Airlines became the 777's launch customer when it placed an order for 34 Pratt & Whitney-powered aircraft valued at US$11 billion with options on an additional 34.[25][26] The development phase coincided with United's replacement program for its aging DC-10s.[27] United required that the new aircraft be capable of flying three different routes: Chicago to Hawaii, Chicago to Europe, and non-stop from Denver, a hot and high airport, to Hawaii.[27] ETOPS certification was also a priority for United,[28] given the overwater portion of United's Hawaii routes.[25] In January 1993, a team of United developers joined other airline teams and Boeing designers at the Everett factory.[29] The 240 design teams, with up to 40 members each, addressed almost 1,500 design issues with individual aircraft components.[30] The fuselage diameter was increased to suit Cathay Pacific, the baseline model grew longer for All Nippon Airways, and British Airways' input led to added built-in testing and interior flexibility,[14] along with higher operating weight options for the basic aircraft.[31]

The 777 was the first commercial aircraft designed entirely on computer.[19][25][32] Each design drawing was created on a three-dimensional CAD software system known as CATIA, sourced from Dassault Systemes and IBM.[33] This lets engineers assemble a virtual aircraft, in simulation, to check for interference and verify that the thousands of parts fit properly—thus reducing costly rework.[34] Boeing developed their own high-performance visualization system, FlyThru, later called IVT (Integrated Visualization Tool) to support large-scale collaborative engineering design reviews, production illustrations, and other uses of the CAD data outside of engineering.[35] Boeing was initially not convinced of CATIA's abilities and built a physical mock-up of the nose section to verify its results. The test was so successful that additional mock-ups were canceled.[36]

Production and testing

The production process included substantial international content, with an unprecedented level of global subcontracting for a Boeing jetliner,[37] exceeded only by the later 787.[38] International contributors included Mitsubishi Heavy Industries and Kawasaki Heavy Industries (fuselage panels),[39] Fuji Heavy Industries, Ltd. (center wing section),[39] Hawker de Havilland (elevators), and Aerospace Technologies of Australia (rudder).[40] An agreement between Boeing and the Japan Aircraft Development Corporation, representing Japanese aerospace contractors, made the latter risk-sharing partners for 20 percent of the entire development program.[37] The initial 777-200 model was launched with propulsion options from three manufacturers, General Electric, Pratt & Whitney, and Rolls-Royce,[41] giving the airlines their choice of engines from competing firms.[42] Each manufacturer had agreed to develop an engine in the 77,000 lbf (340 kN) and higher thrust class (a measure of jet engine output) to power the world's largest twinjet.[41]

Aircraft factory. Rectangular building with six doors, one of which is open to reveal an emerging airliner. The background is a forest; small vehicles and taxiways surround the factory.
An Air India Boeing 777-200LR is rolled out of the Boeing Everett Factory

To accommodate production of its new airliner, Boeing doubled the size of the Everett factory at the cost of nearly US$1.5 billion[25] to provide space for two new assembly lines.[27] New production methodologies were developed, including a turn machine that could rotate fuselage subassemblies 180 degrees, giving workers access to upper body sections.[33] Major assembly of the first aircraft began on January 4, 1993.[43] By the start of production, the program had amassed 118 firm orders, with options for 95 more from 10 airlines.[44] Total investment in the program was estimated at over US$4 billion from Boeing, with an additional US$2 billion from suppliers.[45]

On April 9, 1994, the first 777, line number WA001, was rolled out in a series of 15 ceremonies held during the day to accommodate the 100,000 invited guests.[46] The first flight took place on June 12, 1994,[47] under the command of chief test pilot John E. Cashman.[48] This marked the start of an 11-month flight test program that was more extensive than testing for any previous Boeing model.[49] Nine aircraft fitted with General Electric, Pratt & Whitney, and Rolls-Royce engines[47] were flight tested at locations ranging from the desert airfield at Edwards Air Force Base in California[50] to frigid conditions in Alaska, mainly Fairbanks International Airport.[51] To satisfy ETOPS requirements, eight 180-minute single-engine test flights were performed.[52] The first aircraft built was used by Boeing's nondestructive testing campaign from 1994 to 1996, and provided data for the −200ER and −300 programs.[53] At the successful conclusion of flight testing, the 777 was awarded simultaneous airworthiness certification by the U.S. Federal Aviation Administration (FAA) and European Joint Aviation Authorities (JAA) on April 19, 1995.[47]

Entry into service

Airliner takeoff. The jet's nose is angled upwards as it lifts above the runway, with landing gear still deployed.
The first Boeing 777-200 in commercial service, United Airlines' N777UA

Boeing delivered the first 777 to United Airlines on May 15, 1995.[54][55] The FAA awarded 180-minute ETOPS clearance ("ETOPS-180") for the Pratt & Whitney PW4084-engined aircraft on May 30, 1995, making it the first airliner to carry an ETOPS-180 rating at its entry into service.[56] Longer ETOPS clearance of 207 minutes was approved the following October.[57] The first commercial flight took place on June 7, 1995, from London Heathrow Airport to Dulles International Airport near Washington, D.C.[58]

On November 12, 1995, Boeing delivered the first model with General Electric GE90-77B engines to British Airways,[59] which placed the aircraft into service five days later.[60] Initial service was affected by gearbox bearing wear issues, which caused the airline to temporarily withdraw its 777 fleet from transatlantic service in 1997.[60] British Airways' aircraft returned to full service later that year,[50] and General Electric subsequently announced engine upgrades.[50]

The first Rolls-Royce Trent 877-powered aircraft was delivered to Thai Airways International on March 31, 1996,[59] completing the introduction of the three powerplants initially developed for the airliner.[61] Each engine-aircraft combination had secured ETOPS-180 certification from the point of entry into service.[62] By June 1997, orders for the 777 numbered 323 from 25 airlines, including satisfied launch customers that had ordered additional aircraft.[47] Operations performance data established the consistent capabilities of the twinjet over long-haul transoceanic routes, leading to additional sales.[63] In long term average Boeing claims a dispatch reliability figure (rate of takeoff with no more than 15 minutes delay due to technical issues) of the 777 family of above 99 percent[64] with rates at a time in 2013 at 99.4 percent.[65]

Initial derivatives

Airliner takeoff. Side view of jet ascending in the sky, with landing gear in partially retracted position.
A Malaysia Airlines 777-200ER

After the original model, Boeing developed an increased gross weight variant of the 777-200 with greater range and payload capability.[66] Initially named 777-200IGW,[67] the 777-200ER first flew on October 7, 1996,[68] received FAA and JAA certification on January 17, 1997,[69] and entered service with British Airways on February 9, 1997.[69] Offering greater long-haul performance, the variant became the most widely ordered version of the aircraft through the early 2000s.[66] On April 2, 1997, a Malaysia Airlines −200ER named "Super Ranger" broke the great circle "distance without landing" record for an airliner by flying eastward from Boeing Field, Seattle to Kuala Lumpur, a distance of 10,823 nautical miles (20,044 km), in 21 hours and 23 minutes.[70]

Following the introduction of the −200ER, Boeing turned its attention to a stretched version of the airliner. On October 16, 1997, the 777-300 made its first flight.[68] At 242.4 ft (73.9 m) in length, the −300 became the longest airliner yet produced (until the A340-600), and had a 20 percent greater overall capacity than the standard length model.[71] The −300 was awarded type certification simultaneously from the FAA and JAA on May 4, 1998,[72] and entered service with launch customer Cathay Pacific on May 27, 1998.[68][73]

From the start of the development program, Boeing had considered building ultra-long-range variants.[74] Early plans centered on a 777-100X proposal,[75] which would have been a shortened version of the −200 with reduced weight and increased range,[75] similar to the 747SP.[76] However, the −100X would have carried fewer passengers than the −200 while having similar operating costs, leading to a higher cost per seat.[75][76] By the late 1990s, design plans shifted to longer-range versions of existing models.[75] A more powerful engine in the 100,000 lbf (440 kN) and higher thrust class was required, leading to active discussions between Boeing and the engine manufacturers. General Electric offered to develop the GE90-115B engine,[42] while Rolls-Royce proposed developing the Trent 8104 engine.[77] In 1999, Boeing announced an agreement with General Electric, beating out rival proposals.[42] As part of the deal with General Electric, Boeing agreed they would only offer GE90 engines on new 777 versions.[42]

Longer-range models

Aircraft engine, forward-facing view with a Boeing engineer in front to demonstrate the engine's size. The engine's large circular intake contains a center hub with a swirl mark, surrounded by multiple curved fan blades.
A GE90 engine mounted on a 777-300ER with a Boeing engineer to show the engine's size. A single GE90 engine has powered GE's test 747 during flight.[78]

On February 29, 2000, Boeing launched its next-generation twinjet program,[79] initially called 777-X,[74] and began issuing offers to airlines.[66] Development of the long-range models was slowed by the airline industry downturn, which lasted through the early 2000s.[68] The first model to emerge from the program, the 777-300ER, was launched with an order for ten aircraft from Air France,[80] along with additional commitments.[66] On February 24, 2003, the −300ER made its first flight, and the FAA and EASA (European Aviation Safety Agency, successor to the JAA) certified the model on March 16, 2004.[81] The first delivery to Air France took place on April 29, 2004.[68] The −300ER, which combined the −300's added capacity with the −200ER's range, became the top-selling 777 variant in the late 2000s,[82] gaining orders as airlines replaced comparable four-engine models with twinjets because of their lower operating costs.[83]

The second long-range model, the 777-200LR, rolled out on February 15, 2005, and completed its first flight on March 8, 2005.[68] The −200LR was certified by both the FAA and EASA on February 2, 2006,[84] and the first delivery to Pakistan International Airlines occurred on February 26, 2006.[85] On November 10, 2005, the first −200LR set a record for the longest non-stop flight of a passenger airliner by flying 11,664 nautical miles (21,602 km) eastward from Hong Kong to London.[6] Lasting 22 hours and 42 minutes, the flight surpassed the −200LR's standard design range and was logged in the Guinness World Records.[5][86]

The production freighter model, the 777F, rolled out on May 23, 2008.[87] The maiden flight of the 777F, which used the structural design and engine specifications of the −200LR[88] along with fuel tanks derived from the −300ER,[89] occurred on July 14, 2008.[90] FAA and EASA type certification for the freighter was received on February 6, 2009,[91] and the first delivery to launch customer Air France took place on February 19, 2009.[92][93]

Initially second to the 747 as Boeing's most profitable jetliner,[94] the 777 became the company's most lucrative model in the 2000s.[95] Program sales accounted for an estimated US$400 million of Boeing's pretax earnings in 2000, US$50 million more than the 747.[94] By 2004, the airliner comprised the bulk of wide-body revenues for the Boeing Commercial Airplanes division.[96] In 2007, orders for second-generation 777 models approached 350 aircraft,[97] and in November of that year, Boeing announced that all production slots were sold out to 2012.[83] The program backlog of 356 orders was valued at US$95 billion at list prices in 2008.[98]

Production updates

Aircraft takeoff. Quarter view of aircraft ascending in the sky, with landing gear still deployed.
An All Nippon Airways 777-300ER taking off

In 2010, Boeing announced plans to increase 777 production from 5 aircraft per month to 7 aircraft per month by mid-2011, and 8.3 per month by early 2013.[99] Complete assembly of each 777-300ER requires 49 days.[100] In November 2011, Boeing began assembly of the 1,000th 777, a −300ER model for Emirates;[100] the aircraft was rolled out in March 2012.[101] In late 2011, the FAA assigned a common type rating to the 787 and 777, allowing pilots qualified on either aircraft to operate both models, due to related design features.[102] The smaller 787 was the first stage of a replacement aircraft initiative called the Boeing Yellowstone Project.[103] According to industry reports, the 777 could eventually be replaced by a new product family, the Boeing Yellowstone 3, which would draw upon technologies from the 787.[97]

By the late 2000s, the 777 was facing the possibility of increased competition from Airbus' planned A350 XWB and internally from proposed variants of the 787,[97] both airliners that promise fuel efficiency improvements. As a consequence, the 777-300ER received an engine and aerodynamics improvement package for reduced drag and weight.[104] In 2010, the variant further received a 5,000 lb (2,300 kg) maximum zero-fuel weight increase, equivalent to a higher payload of 20–25 passengers; its GE90-115B1 engines received a 1–2.5 percent thrust enhancement for increased takeoff weights at higher-altitude airports.[104] More design changes were targeted for late 2012, including possible extension of the wingspan,[104] along with other major changes, including a composite wing, new powerplant, and different fuselage lengths.[104][105][106] Emirates was reported as working closely with Boeing on the project, with the possibility of being the launch customer for new versions of the 777.[107]

777X program

View of airport tarmac with terminal building and multiple airliners parked adjacent to it.
A row of Emirates 777s at Dubai International Airport. The carrier has been involved in discussions on the 777X.

In September 2011, Boeing released more details on proposed new 777 versions, collectively referred to as 777X and tentatively designated 777-8X and 777-9X.[108] The 777-9X is to feature extended horizontal stabilizers compared to the 777-300ER and a fuselage stretch of 7.0 ft (2.13 m) to a total length of 250 ft 11 in (76.5 m) to accommodate 407 passengers.[109][110] The 777-9X's planned length exceeds the 250 ft 2 in (76.3 m) length of the 747-8, currently the world's longest airliner. Wingspan was expected to increase from the current 212 ft 7 in (64.8 m) to 234 ft (71.3 m), and incorporate the use of carbon-fiber-reinforced polymer in its construction.[89][108] In addition, gross weight was tentatively slated to decrease slightly from the current 775,000 lb (352,000 kg) to approximately 759,000 lb (344,000 kg) for the −9X model.[109] Boeing was also studying an ultra long-range replacement for the 777-200LR, conceptually dubbed the 777-8LX, which would share the –9X's fuel capacity and gross weight. Its range will be 9,480 nmi (10,910 mi; 17,560 km) compared to 9,395 nmi (10,812 mi; 17,400 km) for the −200LR,[109] and its fuselage length will be 228.17 ft (69.5 m).[108] Preliminary estimates placed entry into service for the first 777X variants at around 2019.[111][112]

In February 2012, General Electric disclosed studies on a slightly smaller engine, dubbed the GE9X, to power the 777X. It was to feature the same fan diameter from the GE90-115B (128 in or 325 cm) and a thrust decrease to new ratings of 99,500 lbf (443 kN) per engine for the –9X and –8LX.[113][114][115] Rolls-Royce and Pratt & Whitney also proposed powerplants for the 777X, including the RB3025 concept, based off the Trent 1000 and Trent XWB engines, and an adaptation of PW1000G engine architecture to produce up to 100,000 lbf (440 kN) of thrust.[108] However, in March 2013 the General Electric GE9X was selected as the exclusive engine to power the 777X.[116] GE subsequently recently updated the GE9X specifications to reflect growing concerns that the 777X would be underpowered. Design changes included a slight increase of thrust to 102,000 lbf (450 kN) (and then again to 105,000 lbf (470 kN)[117]) and a new fan diameter of 132 in (335 cm), giving the new engine the largest fan GE has ever produced.[118][119][120]

In August 2012, the Seattle Times reported that Boeing had slowed 777X development, but still planned for it to begin service by about 2019.[121] Boeing's board of directors gave formal permission for its Commercial Airplanes division to start offering the 777X to customers in May 2013.[122] On September 19, 2013, Lufthansa's supervisory board gave approval to order 34 Boeing 777-9X aircraft to replace their 747-400s, in advance of the program's official launch.[123][124][125] In October 2013, Boeing announced that its U.S. facilities in Charleston, Huntsville, Long Beach, Philadelphia, and St. Louis as well as Russian facilities in Moscow would support the 777X design effort.[126]

Boeing officially launched the 777X at the 2013 Dubai Airshow in November 2013, announcing a total of 259 orders worth more than US$95 billion.[127] According to Boeing, this is the largest product launch by dollar value in the history of commercial aviation.[128] The 777X program includes two models: the 777-9X, which is stretched beyond the length of the 777-300ER, and the 777-8X, which is sized close to the 777-300ER but with ultra-long range capability.[129] In addition to the 34 aircraft commitment from Lufthansa in September 2013, Boeing received orders and commitments at the Dubai Airshow for 150 aircraft from Emirates, 25 aircraft from Etihad Airways and 50 aircraft from Qatar Airways.[127][129][130] In December 2013 Cathay Pacific ordered 21 777-9X airliners with deliveries in 2021-2024.[131]

Design

Aircraft belly section. Close view of engines, extended landing gear and angled control flaps.
Engines, extended slats, flaps, and landing gear of an American Airlines 777-200ER

Boeing introduced a number of advanced technologies with the 777 design, including fully digital fly-by-wire controls,[132] fully software-configurable avionics, Honeywell LCD glass cockpit flight displays,[133] and the first use of a fiber optic avionics network on a commercial airliner.[134] Boeing made use of work done on the cancelled Boeing 7J7 regional jet,[135] which utilized similar versions of the chosen technologies.[135] In 2003, Boeing began offering the option of cockpit electronic flight bag computer displays.[136] In 2013, Boeing announced that the upgraded 777X models would incorporate airframe, systems, and interior technologies from the 787.[137]

Fly-by-wire

In designing the 777 as its first fly-by-wire commercial aircraft, Boeing decided to retain conventional control yokes rather than change to sidestick controllers as used in many fly-by-wire fighter aircraft and in many Airbus airliners.[132] Along with traditional yoke and rudder controls, the cockpit features a simplified layout that retains similarities to previous Boeing models.[138] The fly-by-wire system also incorporates flight envelope protection, a system that guides pilot inputs within a computer-calculated framework of operating parameters, acting to prevent stalls and overly stressful maneuvers.[132] This system can be overridden by the pilot in command if deemed necessary.[132] The fly-by-wire system is supplemented by mechanical backup.[139]

Airframe and systems

Aircraft landing gear. Six wheel gear on the ground, with attachment assembly and gear door leading up to the aircraft belly.
The six-wheel undercarriage of a Boeing 777-300

The wings on the 777 feature a supercritical airfoil design that is swept back at 31.6 degrees and optimized for cruising at Mach 0.83 (revised upward after flight tests to Mach 0.84).[140] The wings are designed with increased thickness and a longer span than previous airliners, resulting in greater payload and range, improved takeoff performance, and a higher cruising altitude.[47] The wings also serve as fuel storage, with longer-range models able to carry up to 47,890 US gallons (181,300 L) of fuel.[89] This capacity allows the 777-200LR to operate ultra-long-distance, trans-polar routes such as Toronto to Hong Kong.[141] In 2013, a new wing made of composite materials was introduced for the upgraded 777X, with a wider span and design features based on the 787's wings.[137]

Large folding wingtips, 21 feet (6.40 m) long, were offered when the 777 was first launched, to appeal to airlines who might use gates made to accommodate smaller aircraft, but no airline purchased this option.[142] Folding wingtips reemerged as a design feature at the announcement of the upgraded 777X in 2013. Smaller folding wingtips of 11 feet (3.35 m) in length will allow 777X models to use the same airport gates and taxiways as earlier 777s.[137] These smaller folding wingtips are less complex than those proposed for earlier 777s, and internally only affect the wiring needed for wingtip lights.[137]

The airframe incorporates the use of composite materials, which comprise nine percent of its original structural weight (all models outside the 777-8X and 777-9X).[143] Elements made from composite material include the cabin floor and rudder. The main fuselage cross-section is circular[144] and tapers rearward into a blade-shaped tail cone with a port-facing auxiliary power unit.[4] The aircraft also features the largest landing gear and the biggest tires ever used in a commercial jetliner.[145] The six-wheel bogies are designed to spread the load of the aircraft over a wide area without requiring an additional centerline gear. This helps reduce weight and simplifies the aircraft's braking and hydraulic systems. Each tire of a 777-300ER six-wheel main landing gear can carry a load of 59,490 lb (26,980 kg), which is heavier than other wide-bodies such as the 747-400.[146] The aircraft has triple redundant hydraulic systems with only one system required for landing.[147] A ram air turbine –a small retractable propeller which can provide emergency power– is also fitted in the wing root fairing.[148]

Interior

Airliner cabin. Rows of seats arranged between two aisles. Each seatback has a monitor; light shines from the sidewalls and overhead bins.
Economy class cabin of Etihad Airways 777-300ER in a 3-3-3 layout

The original 777 interior, also known as the Boeing Signature Interior, features curved panels, larger overhead bins, and indirect lighting.[60] Seating options range from six abreast in first class up to 10 across in economy.[149] The 777's windows were the largest of any current commercial airliner until the 787, and measure 15-inch (380 mm) by 10-inch (250 mm) in size (all models outside the 777-8X and 777-9X).[150] The cabin also features "Flexibility Zones", which entails deliberate placement of water, electrical, pneumatic, and other connection points throughout the interior space, allowing airlines to move seats, galleys, and lavatories quickly and more easily when adjusting cabin arrangements.[149] Several aircraft have also been fitted with VIP interiors for non-airline use.[151] Boeing engineers designed a new hydraulically damped toilet seat cover hinge that closes slowly.[152]

In 2003, Boeing introduced overhead crew rests as an option on the 777.[153] Located above the main cabin and connected via staircases, the forward flight crew rest contains two seats and two bunks, while the aft cabin crew rest features multiple bunks.[153] The Signature Interior has since been adapted for other Boeing wide-body and narrow-body aircraft, including 737NG, 747-400, 757-300, and newer 767 models, including all 767-400ER models.[154][155] The 747-8 and 767-400ER have also adopted the larger, more rounded windows of the original 777.

In 2011, Flight International reported that Boeing is considering replacing the Signature Interior on the 777 with a new interior similar to that on the 787, as part of a move towards a "common cabin experience" across all Boeing platforms.[156] With the launch of the 777X in 2013, Boeing confirmed that the aircraft would be receiving a new interior featuring 787 cabin elements and larger windows.[137]

Variants

Aircraft in flight, underside view. The jet's two wings have one engine each. The rounded nose leads to a straight body section, which tapers at the tail section with its two rear fins.
Planform view of an Air France Boeing 777-200ER in flight

Boeing uses two characteristics, fuselage length and range, to define their 777 models.[16] Fuselage length affects the number of passengers and amount of cargo that can be carried; the 777-200 and derivatives are the base size, and the aircraft was stretched into the 777-300 in 1998. In terms of range, the aircraft has been categorized into three segments based on design criteria; these were initially defined as the following:

  • A-market: up to 4,200 nautical miles (7,800 km)[157]
  • B-market: 6,600 nautical miles (12,200 km)[157]
  • C-market: 7,800 nautical miles (14,400 km)[158]

When referring to different variants, Boeing and airlines often collapse the model number (777) and the variant designator (−200 or −300) into a truncated form (e.g. "772" or "773"[159]). The International Civil Aviation Organization (ICAO) aircraft type designator system adds a preceding manufacturer letter (e.g. "B772" or "B773").[160] Subsequent to the capacity number, designations may or may not append the range identifier (e.g. 777-300ER as "773ER",[161] "773B",[162] "77W",[163] or "B77W"[160]). These notations may be found in aircraft manuals or airline timetables.

777-200

Aircraft in flight, surrounded by white clouds. Side view of twin-engine jet in the sky.
A Boeing 777-200 in Boeing's original livery. Note the tail logos of the aircraft's firm customers below the windows under "Boeing 777".

The 777-200 was the initial A-market model. The first −200 was delivered to United Airlines on May 15, 1995.[68] With a maximum range of 5,235 nautical miles (9,695 km),[164] the −200 was chiefly aimed at U.S. domestic airline operators.[16] Nine different −200 customers have taken delivery of 88 aircraft,[1] with 85 in airline service as of July 2012.[165] The competing aircraft from Airbus is the A330-300.[166]

777-200ER

Aircraft during landing approach. Front quarter view of twin-engine jet in flight with flaps and landing gear extended.
An El Al 777-200ER landing at London Heathrow Airport

The 777-200ER ("ER" for Extended Range), the B-market version of the −200, was originally known as the 777-200IGW for its increased gross weight.[67] The −200ER features additional fuel capacity and an increased maximum takeoff weight (MTOW) over the −200.[164] Aimed at international airlines operating transatlantic routes,[16] the −200ER's maximum range is 7,700 nautical miles (14,300 km).[164] In addition to breaking the eastbound great circle "distance without landing" record, the −200ER also holds the record for the longest ETOPS-related emergency flight diversion (177 minutes under one engine), on a United Airlines flight carrying 255 passengers on March 17, 2003, over the Pacific Ocean.[167][168]

The first −200ER was delivered to British Airways on February 6, 1997.[68] Singapore Airlines, one of the type's largest customers,[1] ordered over half of its −200ERs with reduced engine thrust specifications (de-rated) for use on medium-length routes.[169][170] The de-rated engines lower MTOW, which reduces the aircraft's purchase price and landing fees, and can be re-rated to full −200ER standard for long-haul operations.[169] As of August 2013, −200ER deliveries to 33 different customers totaled 422.[1] As of July 2013, 418 examples of the −200ER were in airline service.[165] The competing aircraft from Airbus was the A340-300.[171]

777-300

Aircraft during landing approach. Front quarter view of twin-engine jet in flight with flaps and landing gear extended.
An Emirates 777-300 in the 2006 FIFA World Cup livery on final approach to London Heathrow Airport, England.

The stretched 777-300 was designed as an A-market replacement for 747-100s and 747-200s.[172] Compared to the older 747s, the stretched 777 has comparable passenger capacity and range, and is designed to burn one-third less fuel and have 40 percent lower maintenance costs.[71] The −300 features a 33.3 ft (10.1 m) fuselage stretch over the baseline −200. This allows seating for up to 550 passengers in a single class high-density configuration,[71] an arrangement adopted for heavily trafficked Japanese routes.[173] Because of the aircraft's length, the −300 is equipped with a tailskid and ground maneuvering cameras to aid pilots during taxi.[174] The maximum range is 6,015 nautical miles (11,140 km),[175] allowing the −300 to operate trunk routes previously flown by older 747s.[71]

After being certified simultaneously by the FAA and JAA,[72] the first −300 was delivered to Cathay Pacific on May 21, 1998.[68][73] Eight different −300 customers have taken delivery of 60 aircraft,[1] and all were in airline service as of July 2012.[165] However, following the introduction of the longer-range −300ER in 2004, all operators have selected the ER version of the base −300 model.[1] The −300 has no direct Airbus rival, but the A340-600 has been offered in competition.[176][177]

777-200LR

Aircraft landing approach. Front quarter view of twin-engine jet in flight with flaps and landing gear extended.
The first 777-200LR built, in service with Pakistan International Airlines

The 777-200LR ("LR" for Longer Range), the C-market model, became the world's longest-range commercial airliner when it entered service in 2006.[178][179] Boeing named this aircraft the Worldliner, highlighting its ability to connect almost any two airports in the world,[6] although it is still subject to ETOPS restrictions.[180] It holds the world record for the longest nonstop flight by a commercial airliner,[6] and has a maximum design range of 9,380 nautical miles (17,370 km).[86] The −200LR was intended for ultra-long-haul routes such as Los Angeles to Singapore.[74]

Developed alongside the −300ER, the −200LR features an increased MTOW and three optional auxiliary fuel tanks in the rear cargo hold.[178] Other new features include raked wingtips, redesigned main landing gear, and additional structural strengthening.[178] As with the −300ER and 777F, the −200LR is equipped with wingtip extensions of 12.8 ft (3.90 m).[178] The −200LR is powered by GE90-110B1 or GE90-115B turbofans.[89] The first −200LR was delivered to Pakistan International Airlines on February 26, 2006.[85][181] As of February 2013, nine different −200LR customers have taken delivery of 55 aircraft, with 3 unfilled orders.[1] Airlines operated 52 of the −200LR variant as of July 2012.[165] The closest competing aircraft from Airbus was the A340-500HGW.[178]

777-300ER

Aircraft landing approach. Side view of twin-engine jet in flight with flaps and landing gear extended.
An Air Canada 777-300ER landing with flaps deployed

The 777-300ER ("ER" for Extended Range) is the C-market version of the −300. It features raked and extended wingtips, a new main landing gear, reinforced nose gear, and extra fuel tanks.[182][183] It also has a strengthened fuselage, wings, empennage, and engine attachments.[89] The -300ER is powered by the GE90-115B turbofan, which is the world's most powerful jet engine in service, with a maximum thrust of 115,300 lbf (513 kN).[182] Its maximum range is 7,930 nautical miles (14,690 km),[184] made possible by higher MTOW and increased fuel capacity.[176][177] The −300ER can fly approximately 34 percent further than the −300 with a full load of passengers and cargo.[89] Following flight testing, aerodynamics refinements have reduced fuel burn by an additional 1.4 percent.[82][185]

The first −300ER was delivered to Air France on April 29, 2004.[68][186] The −300ER is the best-selling 777 variant, having surpassed the −200ER in orders in 2010 and deliveries in 2013.[1] Since its launch, the model has been a primary driver of the twinjet's sales past the rival A330/340 series.[97] Using two engines produces a typical operating cost advantage of around 8–9 percent for the −300ER over the A340-600,[187] along with a 20 percent fuel burn advantage over the 747-400.[83] Several airlines have acquired the −300ER as a 747-400 replacement amid rising fuel prices.[83] As of August 2013, −300ER deliveries to 24 different customers totaled 424, with 287 unfilled orders.[1] Operators had 346 aircraft in service as of July 2012.[165] The −300ER's direct Airbus competitors have included the A340-600HGW and the upcoming A350-1000.[97][177]

777 Freighter

Side view of aircraft over runway. Runway surfaces in foreground and forest in background.
The first 777 Freighter, destined for Air France, during a test flight

The 777 Freighter (777F) is an all-cargo version of the twinjet, and shares features with the −200LR; these include its airframe, engines,[188] and fuel capacity.[89] With a maximum payload of 226,000 lb (103,000 kg),[89] cargo capacity is similar to the 243,000 lb (110,000 kg) of the 747-200F.[83] The freighter has a range of 4,900 nmi (9,070 km) at maximum payload,[89] although greater range is possible if less cargo weight is carried.[189]

As the aircraft promises improved operating economics compared to existing freighters,[83] airlines have targeted the 777F as a replacement for older freighters including the 747-200F, MD-10, and MD-11F.[88][190] The first 777F was delivered to Air France on February 19, 2009.[92] As of February 2013, 74 freighters had been delivered to eleven different customers, with 53 unfilled orders.[1] Operators had 61 of the 777F in service as of July 2012.[165]

In the 2000s, Boeing began studying the conversion of 777-200ER and −200 passenger airliners into freighters, under the name 777 BCF (Boeing Converted Freighter).[191] The company has been in discussion with several airline customers, including FedEx Express, UPS Airlines, and GE Commercial Aviation Services, to provide launch orders for a 777 BCF program.[192]

777-8X

The 777-8X is the replacement to the 777-300ER and will seat about 350 passengers in a three-class configuration and fly more than 9,300 nmi (17,200 km). It is to be a direct competitor to the Airbus A350-1000.[122][193]

777-9X

The 777-9X is a further stretched variant with seating for about 400 passengers in a three-class configuration and a range of more than 8,200 nmi (15,200 km). Boeing states that it will have "no competitor in its market segment".[122][117][125] The 777-9X is due to begin production in 2017 and enter service in 2020.[194]

777 Tanker (KC-777)

The KC-777 was a proposed tanker version of the 777. In September 2006, Boeing announced that it would produce the KC-777, if the United States Air Force (USAF) required a larger tanker than the KC-767. The 777 tanker would have been able to transport more cargo or personnel.[195][196][197] In April 2007, Boeing instead offered its KC-767 Advanced Tanker for USAF's KC-X competition.[198]

Operators

Aircraft takeoff. Side view of twin-engine jet in flight with flaps and landing gear extended, with upswept wings.
Japan Airlines 777-200 ascending following takeoff from Tokyo Haneda International Airport in 2010
Side view of twin-engine jet in flight with flaps and landing gear extended.
Biman Bangladesh Airlines 777-300ER on short final at London Heathrow Airport in 2012.
Main article: List of Boeing 777 operators

The customers that have received the most 777s are ILFC, Emirates, Singapore Airlines, United Airlines, and Air France.[1] Emirates is the largest airline operator as of September 2013,[165] and is the only customer to have operated all 777 variants produced, including the −200, −200ER, -200LR, −300, −300ER, and 777F.[1][199] The 1,000th 777 off the production line, a −300ER set to be Emirates' 102nd 777, was unveiled at a factory ceremony in March 2012.[101]

A total of 1,094 aircraft (all variants) were in airline service as of September 2013, with Emirates (127), United Airlines (74), Air France (64), Singapore Airlines (56), American Airlines (55) All Nippon Airways (54), British Airways (53), Cathay Pacific (49), Japan Airlines (46) and other operators with fewer aircraft of the type.[200]

Orders and deliveries

Main article: List of Boeing 777 orders and deliveries
Orders and deliveries
Orders Deliveries
Type Total Unfilled Total 2013 2012 2011 2010 2009 2008 2007 2006 2005 2004 2003 2002 2001 2000 1999 1998 1997 1996 1995
777-200 88 88 1 3 2 1 3 9 3 10 11 32 13
777-200ER 422 422 4 3 3 4 3 19 23 13 22 29 41 55 42 63 50 48
777-200LR 59 3 56 1 1 6 9 16 11 10 2
777-300 60 60 1 4 2 9 6 3 4 17 14
777-300ER 721 269 452 79 60 52 40 52 47 53 39 20 10
777F 128 42 86 14 19 15 22 16
777X 66 66
Total 1544 380 1164 98 83 73 74 88 61 83 65 40 36 39 47 61 55 83 74 59 32 13

Data through December 31, 2013[1][201][202][203][204]

ICAO designation[160] Model series
B772 777-200
777-200ER
B77L 777-200LR
777F
B773 777-300
B77W 777-300ER

Incidents and accidents

Heat exchanger. Circular latticework with an uneven covering of small particles over part of its surface.
Laboratory replication of ice crystals clogging the fuel-oil heat exchanger on a Rolls-Royce Trent 800 engine, from the NTSB report on the BA38 and DL18 incidents[205]

As of 2013, the 777 has been in eight aviation accidents and incidents,[206] including three hull-loss accidents,[207] and three hijackings.[208] Before 2013, the only fatality involving the twinjet occurred in a refueling fire at Denver International Airport on September 5, 2001, during which a ground worker sustained fatal burns.[209] The aircraft, operated by British Airways, suffered fire damage to the lower wing panels and engine housing; it was later repaired and put back into service.[209][210]

The type's first hull-loss occurred on January 17, 2008, when British Airways Flight 38, a 777-200ER with Rolls-Royce Trent 895 engines flying from Beijing to London, crash-landed approximately 1,000 feet (300 m) short of Heathrow Airport's runway 27L and slid onto the runway's threshold. There were 47 injuries and no fatalities. The impact damaged the landing gear, wing roots and engines. The aircraft was written off.[211][212] Upon investigation, the accident was blamed on ice crystals from the fuel system clogging the fuel-oil heat exchanger (FOHE).[205] In 2009, air accident investigators called for a redesign of this component on the Trent 800 series engine.[213] Redesigned fuel oil heat exchangers were installed in British Airways' 777s by October 2009.[214]

Two other minor momentary losses of thrust with Trent 895 engines occurred in February and November 2008.[215][216] The National Transportation Safety Board (NTSB) investigators concluded that, just as on BA38, the loss of power was caused by ice in the fuel clogging the fuel-oil heat exchanger. As a result, the heat exchanger was redesigned.[205]

The type's second hull-loss occurred on July 29, 2011, when an EgyptAir 777-200ER registered as SU-GBP suffered a cockpit fire while parked at the gate at Cairo International Airport.[217] The plane was successfully evacuated with no injuries,[217] and airport fire teams extinguished the fire.[218] The aircraft sustained structural, heat and smoke damage. This aircraft was written off.[217][218] Investigators focused on a possible electrical fault with a supply hose in the cockpit crew oxygen system.[217]

The type's third hull loss and first involving fatalities occurred on July 6, 2013, when Asiana Airlines Flight 214, 777-200ER registered HL7742, crashed while landing at San Francisco International Airport after touching down short of the runway. Passengers and crew evacuated before fire destroyed the aircraft. The crash resulted in the death of two of the 307 people on board. A third person died after being struck by an airport fire truck responding to the crash. These were the first fatalities in a crash involving a 777.[219][220][221] An accident investigation by the NTSB is underway; its initial focus is on the aircraft's low landing speed.[222]

Specifications

Comparison chart showing front, side, and dorsal views of the 777.
Diagram of 777-200ER/300ER
Specifications by model
Model 777-200 777-200ER 777-200LR 777 Freighter 777-300 777-300ER 777-8X[193][223][194] 777-9X[193][223][194]
Cockpit crew Two
Seating capacity,
typical 		314 (3-class)[224]
400 (2-class)
440 (maximum)		 N/A
(cargo)		 386 (3-class)[224]
451 (2-class)
550 (maximum)		 353 (3-class) 407 (3-class)
Length 209 ft 1 in (63.7 m) 242 ft 4 in (73.9 m) 228 ft 2 in (69.5 m) 250 ft 11 in (76.5 m)
Wingspan 199 ft 11 in (60.9 m) 212 ft 7 in (64.8 m) 199 ft 11 in (60.9 m) 212 ft 7 in (64.8 m) Unfolded: 233 ft 3 in (71.1 m)
Folded: 212 ft 8 in (64.8 m)
Wing sweepback 31.64° TBA
Tail height 60 ft 9 in (18.5 m) 61 ft 1 in (18.6 m) 60 ft 8 in (18.5 m) 64 ft 6 in (19.7 m)[225]
Cabin width 19 ft 3 in (5.87 m) 20 ft (6.10 m)[226]
Fuselage width 20 ft 4 in (6.20 m)
Maximum cargo capacity 5,720 cu ft (162 m3)
32× LD3		 23,051 cu ft (653 m3)
37× pallets		 7,640 cu ft (216 m3)
44× LD3		 40× LD3 48× LD3
Operating empty weight 297,300 lb
(134,800 kg)		 304,500 lb
(138,100 kg)		 320,000 lb
(145,150 kg)		 318,300 lb
(144,400 kg)		 353,800 lb
(160,500 kg)		 370,000 lb
(167,800 kg)		 TBA
Maximum landing weight 445,000 lb
(201,840 kg)		 470,000 lb
(213,180 kg)		 492,000 lb
(223,168 kg)		 575,000 lb
(260,816 kg)		 524,000 lb
(237,680 kg)		 554,000 lb
(251,290 kg)		 TBA
Maximum takeoff weight 545,000 lb
(247,200 kg)		 656,000 lb
(297,550 kg)		 766,000 lb
(347,500 kg)		 766,800 lb
(347,800 kg)		 660,000 lb
(299,370 kg)		 775,000 lb
(351,500 kg)[117]
Typical cruise speed Mach 0.84 (560 mph, 905 km/h, 490 knots) at a cruise altitude of 35,000 ft (11,000 m) TBA
Maximum speed Mach 0.89 (590 mph, 950 km/h, 512 knots) at a cruise altitude of 35,000 ft (11,000 m) TBA
Maximum range
(at maximum payload) 		5,240 nmi
(9,700 km, 6,027 mi)		 7,725 nmi
(14,310 km, 8,892 mi)		 9,380 nmi
(17,370 km, 10,793 mi)		 4,900 nmi
(9,070 km, 5,636 mi)		 6,005 nmi
(11,120 km, 6,910 mi)		 7,930 nmi
(14,690 km, 9,128 mi)		 > 9,300 nmi
(17,224 km, 10,702 mi)		 > 8,200 nmi
(15,186 km, 9,436 mi)
Takeoff distance at MTOW
(sea level, ISA) 		8,000 ft
2,440 m		 11,100 ft
3,380 m		 9,200 ft
2,800 m		 9,300 ft
2,830 m		 10,600 ft
3,230 m		 10,000 ft
3,050 m		 TBA
Maximum fuel capacity 31,000 US gal
(117,348 L)		 45,220 US gal
(171,176 L)		 47,890 US gal
(181,283 L)		 45,220 US gal
(171,176 L) 		47,890 US gal
(181,283 L)		 TBA
Service ceiling 43,100 ft (13,140 m)
Engine (×2) PW 4077
RR 877
GE90-77B		 PW 4090
RR 895
GE90-94B		 GE90-110B1
GE90-115B1		 PW 4098
RR 892
GE90-92B/-94B		 GE90-115B1 GE9X
Thrust (×2) PW: 77,000 lbf (342 kN)
RR: 76,000 lbf (338 kN)
GE: 77,000 lbf (342 kN)		 PW: 90,000 lbf (400 kN)
RR: 93,400 lbf (415 kN)
GE: 93,700 lbf (417 kN)		 GE −110B: 110,100 lbf (490 kN)
GE −115B: 115,300 lbf (512 kN)		 PW: 98,000 lbf (436 kN)
RR: 93,400 lbf (415 kN)
GE: 92,000/93,700 lbf (409 kN/418 kN)		 GE: 115,540 lbf (514 kN) GE: 105,000 lbf (470 kN)[117]

Notes: Data for the 777X are preliminary.
Sources: Boeing 777 specifications,[89][227] Boeing 777 Airport planning report,[228] and other sources.[229][230][231]

See also

Related development

Aircraft of comparable role, configuration, and era

Related lists

Notes

  1. ^ a b c d e f g h i j k l m n o "777 Model Orders and Deliveries summary". Boeing. December 2013. Retrieved January 6, 2014.
  2. ^ Robertson, David (March 13, 2009). "Workhorse Jet Has Been Huge Success with Airlines that Want to Cut Costs". The Times. London, England, United Kingdom: Times Newspapers. Archived from the original on June 12, 2011. Retrieved March 20, 2009. {{cite news}}: Unknown parameter |deadurl= ignored (|url-status= suggested) (help); Unknown parameter |subscription= ignored (|url-access= suggested) (help)
  3. ^ Grantham, Russell (February 29, 2008). "Delta's new Boeing 777 Can Fly Farther, Carry More". The Atlanta Journal-Constitution. Delta will put the new "triple seven" — as airline folks call the jet — into service March 8. {{cite web}}: |access-date= requires |url= (help); Missing or empty |url= (help)
  4. ^ a b Norris & Wagner 1996, p. 89
  5. ^ a b Glenday 2007, p. 200
  6. ^ a b c d Phillips, Don (November 10, 2005). "Flight of Boeing's 777 Breaks Distance Record". The New York Times. International Herald Tribune. Retrieved October 14, 2013.
  7. ^ "Emirates Fleet". Retrieved June 30, 2013.
  8. ^ "The world's top-five safest aircraft". The Vancouver Sun. August 9, 2011. Retrieved June 17, 2013. {{cite web}}: Italic or bold markup not allowed in: |publisher= (help)
  9. ^ Wells & Rodrigues 2004, p. 146
  10. ^ "The 1980s Generation". Time. August 14, 1978. Retrieved July 19, 2008.
  11. ^ a b Weiner, Eric (December 19, 1990). "New Boeing Airliner Shaped by the Airlines". The New York Times. Retrieved May 8, 2011.
  12. ^ Eden 2008, pp. 98, 102–103
  13. ^ a b Eden 2008, pp. 99–104
  14. ^ a b c d e f Norris & Wagner 1999, p. 128
  15. ^ Yenne 2002, p. 33
  16. ^ a b c d Eden 2008, p. 112
  17. ^ a b c d Norris & Wagner 1999, p. 126
  18. ^ a b c d Norris & Wagner 1999, p. 127
  19. ^ a b Eden 2008, p. 106
  20. ^ Norris & Wagner 2001, p. 11
  21. ^ Norris & Wagner 1996, pp. 9–14
  22. ^ Norris & Wagner 1999, p. 129
  23. ^ a b Birtles 1998, pp. 13–16
  24. ^ Lane, Polly (December 1, 1991). "Aerospace Company May Be Rethinking Commitment To The Puget Sound Area". Seattle Times. Retrieved October 15, 2009.
  25. ^ a b c d Norris & Wagner 1999, p. 132
  26. ^ "Business Notes: Aircraft". Time. October 29, 1990. Retrieved July 19, 2008.
  27. ^ a b c Norris & Wagner 1996, p. 14
  28. ^ Norris & Wagner 1996, p. 13
  29. ^ Norris & Wagner 1996, p. 15
  30. ^ Norris & Wagner 1996, p. 20
  31. ^ "BA Gets New 777 Model". Seattle Post-Intelligencer. February 10, 1997. Retrieved May 8, 2011.
  32. ^ An Introduction to Mechanical Engineering. Cl-Engineering. p. 19. ISBN 978-1-111-57680-6. As an example, the Boeing 777 was the first commercial airliner developed through a paperless computer-aided design process.
  33. ^ a b Norris & Wagner 1999, p. 133
  34. ^ Norris & Wagner 1999, pp. 133–134
  35. ^ Abarbanel & McNeely 1996, p. 124 Note: IVT is still active at Boeing in 2010 with over 29,000 users.
  36. ^ Norris & Wagner 1996, p. 21
  37. ^ a b Eden 2008, p. 108
  38. ^ Hise, Phaedra (July 9, 2007). "The power behind Boeing's 787 Dreamliner". CNN. Retrieved October 15, 2009.
  39. ^ a b Richardson, Michael (February 23, 1994). "Demand for Airliners Is Expected to Soar: Asia's High-Flying Market". International Herald Tribune. Retrieved March 20, 2009.
  40. ^ Sabbagh 1995, pp. 112–114
  41. ^ a b Norris & Wagner 1999, pp. 136–137
  42. ^ a b c d "A question of choice". Flight International. January 3, 2000. Retrieved March 29, 2009.
  43. ^ Sabbagh 1995, pp. 168–169
  44. ^ Norris, Guy (March 31, 1993). "Boeing prepares for stretched 777 launch". Flight International. Retrieved May 8, 2011.
  45. ^ Norris & Wagner 1996, p. 7
  46. ^ Sabbagh 1995, pp. 256–259
  47. ^ a b c d e Eden 2008, p. 107
  48. ^ Birtles 1998, p. 25
  49. ^ Andersen, Lars (August 16, 1993). "Boeing's 777 Will Be Tops When It Comes To ETOPS". Seattle Times. Retrieved March 20, 2009.
  50. ^ a b c Norris & Wagner 1999, p. 144
  51. ^ Birtles 1998, p. 40
  52. ^ Birtles 1998, p. 20
  53. ^ Birtles 1999, p. 34
  54. ^ Birtles 1998, p. 69
  55. ^ "First Boeing 777 delivery goes to United Airlines". Business Wire. May 15, 1995. Retrieved December 1, 2008.
  56. ^ Norris & Wagner 1999, p. 139
  57. ^ 180-minute ETOPS approval was granted to the General Electric GE90 powered 777 on October 3, 1996, and to the Rolls-Royce Trent 800-powered 777 on October 10, 1996.
  58. ^ Birtles 1998, p. 80
  59. ^ a b Eden 2004, p. 115.
  60. ^ a b c Norris & Wagner 1999, p. 143
  61. ^ Norris & Wagner 1999, p. 147
  62. ^ Norris & Wagner 1999, pp. 146–147
  63. ^ "Boeing Roars Ahead". BusinessWeek. November 6, 2005. Retrieved December 1, 2008.
  64. ^ 777 Reliability Data Boeing
  65. ^ Trouble-plagued Dreamliner only 98% reliable, Boeing admits Boeing
  66. ^ a b c d Eden 2008, p. 113
  67. ^ a b Eden 2008, pp. 112–113
  68. ^ a b c d e f g h i j "The Boeing 777 Program Background". Boeing. Retrieved June 6, 2009.
  69. ^ a b Haenggi, Michael. "777 Triple Seven Revolution". Boeing Widebodies. St. Paul, Minnesota: MBI, 2003. ISBN 0-7603-0842-X.
  70. ^ Cite error: The named reference Norris and Wagner, p. 148 was invoked but never defined (see the help page).
  71. ^ a b c d Norris & Wagner 1999, p. 151
  72. ^ a b Norris & Wagner 2001, p. 125
  73. ^ a b Norris & Wagner 1999, pp. 151–157
  74. ^ a b c Norris & Wagner 1999, p. 165
  75. ^ a b c d Norris & Wagner 1999, pp. 165–167
  76. ^ a b Norris, Guy (May 15, 1996). "Boeing sets decision date for new versions of 777". Flight International. Retrieved March 29, 2009.
  77. ^ "Aero-Engines – Rolls-Royce Trent". Jane's Transport Business News. February 13, 2001. Archived from the original on March 25, 2008. Retrieved March 21, 2009. {{cite web}}: Italic or bold markup not allowed in: |publisher= (help)
  78. ^ General Electric Biggest Jet Engine for B-777. History Channel. 2008. Event occurs at 3:00–3:10 min. Retrieved July 11, 2013.
  79. ^ "Boeing launches stretch 777 jetliner". Deseret News. February 29, 2000. Retrieved October 28, 2009.
  80. ^ Song, Kyung (October 5, 2000). "Air France orders 10 777s". Seattle Times. Retrieved September 15, 2009.
  81. ^ Dinell, David (March 16, 2004). "Boeing's 777-300ER receives certification". Wichita Business Journal. Retrieved March 20, 2009.
  82. ^ a b Ostrower, Jon (August 7, 2008). "Green and versatile". Flight International. Retrieved March 29, 2009.
  83. ^ a b c d e f Thomas, Geoffrey (June 13, 2008). "Boeing under pressure as demand rises for fuel-saver 777". The Australian. Retrieved June 20, 2008.
  84. ^ Wallace, James (February 3, 2006). "777 distance champ is certified for service". Seattle Post-Intelligencer. Retrieved December 10, 2008.
  85. ^ a b Chaudhry, Muhammad Bashir (November 18, 2008). "Modernization of PIA fleet". Pakistan Dawn. Retrieved February 12, 2008.
  86. ^ a b "Boeing 777-200LR and 777-300ER Technical Characteristics". Boeing. Retrieved March 20, 2009.
  87. ^ Trimble, Stephen (May 23, 2008). "Boeing 777F makes its debut ahead of flight test phase". Flight International. Retrieved June 6, 2008.
  88. ^ a b "Datafile: Boeing 777F". Flug Revue. 2006. Archived from the original on January 30, 2008. Retrieved March 20, 2009.
  89. ^ a b c d e f g h i j "Boeing 777 – Technical Information". Boeing. Retrieved October 9, 2011.
  90. ^ Ionides, Nicholas (July 15, 2008). "Boeing 777F flies for the first time". Flight International. Retrieved March 20, 2009.
  91. ^ "European Aviation Safety Agency Validates FAA Certification of Boeing 777 Freighter". Reuters. February 6, 2009. Retrieved July 1, 2011.
  92. ^ a b Ionides, Nicholas. "First 777 freighter delivered to Air France". Air Transport Intelligence via Flightglobal.com. Retrieved February 20, 2009.
  93. ^ "Boeing launches cargo version of 777". Associated Press. May 24, 2005. Retrieved March 20, 2009.
  94. ^ a b Song, Kyung (June 4, 2000). "Who builds a better widebody?". Seattle Times. Retrieved October 29, 2009.
  95. ^ Ray, Susanna (April 21, 2009). "Boeing Earnings Buffeted by 777 Production Slump". Bloomberg. Retrieved October 29, 2009.
  96. ^ Gates, Dominic (November 16, 2004). "Freighter version of 777 jetliner in works". Seattle Times. Retrieved October 29, 2009.
  97. ^ a b c d e "Airbus A350 XWB puts pressure on Boeing 777". Flight International. November 26, 2007. Retrieved December 1, 2008.
  98. ^ Hepher, Tim (September 8, 2008). "Sizing up Boeing's plane portfolio". Reuters. Retrieved June 3, 2011.
  99. ^ Ranson, Lori (December 20, 2010). "Boeing unveils another increase in Boeing 777 production". Air Transport Intelligence via Flightglobal.com. Retrieved January 2, 2011.
  100. ^ a b "Boeing Begins Work on 1,000th 777". Boeing. November 7, 2011. Retrieved November 8, 2011.
  101. ^ a b "Emirates airline receives 1,000th Boeing 777". Gulf News. March 3, 2012. Retrieved March 3, 2012.
  102. ^ "Flight Standardization Board Report" (PDF). Federal Aviation Administration. August 25, 2011. Retrieved November 8, 2011.
  103. ^ Norris & Wagner 2009, pp. 32–35.
  104. ^ a b c d "Order trickle continues for in-production widebodies". Flight International. September 8, 2008. Retrieved November 2, 2010.
  105. ^ Ostrower, Jon (September 8, 2008). "Boeing looks to extend 777 wingspan for incremental improvement package". Flight International. Retrieved March 17, 2010.
  106. ^ Ostrower, Jon (June 21, 2011). "PARIS: Boeing mulls 777-9X". Air Transport Intelligence via Flightglobal.com. Retrieved July 4, 2011.
  107. ^ "Emirates may be launch customer for new Boeing 777". Seattle Post-Intelligencer, September 12, 2011. Retrieved September 14, 2011.
  108. ^ a b c d "A special look at the future prospects of the Boeing 777". Flight International. March 2012. Retrieved March 10, 2012.
  109. ^ a b c Ostrower, John (March 7, 2012). "Boeing homes in on late-2012 launch for 777 successor". Flight International. Retrieved March 20, 2012.
  110. ^ Ostrower, Jon (February 13, 2012). "Boeing studies ultra long-range 777-8LX concept". Air Transport Intelligence via Flightglobal.com. Retrieved February 13, 2012.
  111. ^ Tsang, Daniel (September 14, 2011). "New Boeing 777X likely to be a highly efficient derivative". Aspire Aviation. Retrieved November 12, 2011.
  112. ^ Tsang, Daniel (February 9, 2012). "Boeing develops 777X to challenge Airbus A350". Aspire Aviation. Retrieved August 25, 2012.
  113. ^ Ostrower, John (March 7, 2012). "GE plans 10% fuel burn improvement for GE9X engine". Flight International. Retrieved March 20, 2012.
  114. ^ Ostrower, Jon (September 14, 2011). "Next generation 777 comes into focus". Flight International. Retrieved November 12, 2011.
  115. ^ Ostrower, Jon (September 14, 2011). "Boeing's 777-9X comes into focus with a massive CFRP wing". Flightblogger. Retrieved November 12, 2011.
  116. ^ "Boeing selects GE as sole engine partner on next 777 plane". Reuters. March 15, 2013. Retrieved March 19, 2013.
  117. ^ a b c d "Boeing's widebody dominance hinges on 777X success". Aspire Aviation. Retrieved November 20, 2013.
  118. ^ "GE9X - GE Aviation". General Electric. 2013. Retrieved July 1, 2013. {{cite web}}: Italic or bold markup not allowed in: |publisher= (help)
  119. ^ The New GE9X Engine - GE Aviation. General Electric. June 17, 2013. Retrieved July 1, 2013. {{cite AV media}}: Italic or bold markup not allowed in: |publisher= (help)
  120. ^ Alcock, Charles (June 16, 2013). "GE Pushes Envelope With GE9X for New Boeing 777". Aviation International News. Retrieved July 1, 2013.
  121. ^ Gates, Dominic. "Boeing slows the pace on 777X" Seattle Times, August 22, 2012. Retrieved: August 25, 2012.
  122. ^ a b c Norris, Guy (May 1, 2013). "Boeing Board Gives Approval To Offer 777X". Aviation Week & Space Technology. Retrieved July 1, 2013.
  123. ^ Gubisch, Michael (October 2013). "Lufthansa makes widebody move". Flight International. Retrieved November 25, 2013.
  124. ^ Gubisch, Michael (September 19, 2013). "Split Lufthansa widebody order includes firm 777X". Flight Global. Retrieved September 19, 2013.
  125. ^ a b "Boeing Statement on Lufthansa Selection of Boeing 777X for Future Long-Haul Fleet". Boeing, September 19, 2013.
  126. ^ "Boeing spreads 777X design work to Charleston, Moscow, defence sites". Flight Global. October 30, 2013. Retrieved October 31, 2013.
  127. ^ a b Wilhelm, Steve (November 13, 2013). "Boeing Launches 777X with Orders for 259 Jets Worth $95B". Puget Sound Business Journal. Seattle, Washington: American City Business Journals. Archived from the original on November 13, 2013. Retrieved November 13, 2013. The 777X launch customers include Emirates, with an order for 150 aircraft, Qatar Airways with 50, and Etihad Airways with an order for 25 jetliners. These are on top of an existing order for 34 Boeing 777X jets from Lufthansa, providing a total launch order of 259 aircraft worth more than $95 billion. {{cite journal}}: Unknown parameter |deadurl= ignored (|url-status= suggested) (help)
  128. ^ "Dubai Air Show: Boeing Leads Order Books Race". BBC News. BBC. November 17, 2013. Business. Retrieved November 17, 2013. Boeing said its 777 mini-jumbo sales represented 'the largest product launch in commercial jetliner history by dollar value'. {{cite news}}: Unknown parameter |deadurl= ignored (|url-status= suggested) (help)
  129. ^ a b Norris, Guy (November 17, 2013). "Boeing Launches 777X in Dubai Order Boom". Aviation Week. Penton. Retrieved November 17, 2013. {{cite news}}: Unknown parameter |deadurl= ignored (|url-status= suggested) (help)
  130. ^ "Modern, Quiet and Environmentally Efficient: Lufthansa Group Orders 59 Ultra-Modern Wide-Body Boeing 777-9X and Airbus A350-900 Aircraft". Lufthansa Group (Press release). Deutsche Lufthansa AG. September 19, 2013. Retrieved November 17, 2013. ... the Supervisory Board approved the purchase of 59 ultra-modern aircraft for the Group at its meeting yesterday. 34 Boeing 777-9Xs and 25 Airbus A350-900s will be added to the Lufthansa Group's wide-body fleet. {{cite press release}}: Unknown parameter |deadurl= ignored (|url-status= suggested) (help)
  131. ^ "Cathay Pacific orders 21 Boeing 777X planes". Channel News Asia. Retrieved December 27, 2013.
  132. ^ a b c d North, David. "Finding Common Ground in Envelope Protection Systems". Aviation Week & Space Technology, August 28, 2008, pp. 66–68.
  133. ^ Birtles 1998, p. 57
  134. ^ Norris & Wagner 1996, p. 47
  135. ^ a b Sweetman, Bill (September 1, 2005). "The Short, Happy Life of the Prop-fan". Air & Space. Retrieved December 1, 2008.
  136. ^ Corliss, Bryan (November 5, 2003). "New Boeing 777 Boasts Breakthrough Video System". Forbes. Retrieved May 5, 2009.
  137. ^ a b c d e Norris, Guy (November 25, 2013). "Dubai Provides Runway For 777X Program Launch". Aviation Week & Space Technology. Retrieved November 25, 2013.
  138. ^ Ropelewski, Robert (June 1995). "Flying the Boeing 777". Interavia Business & Technology. Retrieved March 21, 2009.
  139. ^ Newhouse 2008, p. 106
  140. ^ Norris & Wagner 1999, p. 130
  141. ^ Morris, Doug (March 2012). "What determines the kind of aircraft that will be used for a particular route?". enRoute.
  142. ^ "Type Acceptance Report – Boeing 777" (PDF). Civil Aviation Authority of New Zealand. Retrieved December 1, 2008.
  143. ^ Norris & Wagner 1996, p. 35
  144. ^ Norris & Wagner 1996, p. 92
  145. ^ Eden 2008, p. 111
  146. ^ Turner, Aimee (March 28, 2006). "ADP to revamp runway at Orly". Flight International. Retrieved April 2, 2009.
  147. ^ Birtles 1998, p. 66
  148. ^ Birtles 1998, p. 60
  149. ^ a b Norris & Wagner 2001, pp. 32–33
  150. ^ Wallace, James (November 26, 2008). "Continental plans Dreamliner seats to be roomy, with a view". Seattle Post-Intelligencer. Retrieved July 1, 2011.
  151. ^ "Lufthansa Technik turns out first customized VIP Boeing 777". Lufthansa Technik. December 22, 2000. Archived from the original on 20090615231836. Retrieved October 25, 2008. {{cite web}}: Check date values in: |archivedate= (help)
  152. ^ Stover, Dawn (June 1994). "The newest way to fly". Popular Science: 78–79, 104. Retrieved March 10, 2011.
  153. ^ a b Wallace, James (February 4, 2003). "Boeing adds places for crews to snooze". Seattle Post-Intelligencer. Retrieved June 3, 2011.
  154. ^ Norris & Wagner 1999, p. 122
  155. ^ Norris & Wagner 1999, pp. 46, 112
  156. ^ Kirby, Mark (July 7, 2011). "Boeing eyes 'common cabin experience' across platforms". Air Transport Intelligence via Flightglobal.com. Retrieved July 8, 2011.
  157. ^ a b Birtles 1999, pp. 103, 105
  158. ^ Norris & Wagner 2001, p. 102
  159. ^ "About our operating aircraft". Japan Airlines. Retrieved October 25, 2009.
  160. ^ a b c "ICAO Document 8643." International Civil Aviation Organization. Retrieved: February 6, 2011.
  161. ^ John, Danny (September 12, 2007). "Air NZ must ask shareholders". Sydney Morning Herald. Retrieved March 30, 2009.
  162. ^ "Cathay Pacific puts its trust in Boeing". Asia Times Online. December 3, 2005. Retrieved March 30, 2009.
  163. ^ "Air Canada – 777-300ER (77W)". Air Canada. Retrieved March 30, 2009.
  164. ^ a b c "777-200/-200ER Technical Characteristics". Boeing. November 21, 2008. Retrieved June 6, 2009.
  165. ^ a b c d e f g "World Airliner Census". Flight International, August 28–September 3, 2012.
  166. ^ Wallace, James (November 19, 2001). "Aerospace Notebook: Conner's best bet – Let it ride on the 777s but airlines aren't ready to commit to 200LR model". Seattle Post-Intelligencer. Retrieved May 8, 2011.
  167. ^ "Still Tops for ETOPS". Air Safety Week. April 14, 2003. Retrieved May 23, 2009.
  168. ^ "Divert Details". Air Safety Week. March 24, 2003. Retrieved May 23, 2009.
  169. ^ a b "SIA's new long-haul LCC to start with 400-seat B777s, plans 16-aircraft fleet within four years". CAPA Centre for Aviation. September 1, 2011. Retrieved March 22, 2012.
  170. ^ "Our Fleet". Singapore Airlines. 2012. Retrieved March 22, 2012.
  171. ^ Wall, Robert (October 30, 2005). "Boeing's Interest Focuses on 747 Advanced, Not 787-10". Aviation Week & Space Technology. Retrieved March 20, 2009.
  172. ^ Norris & Wagner 1999, pp. 151–152
  173. ^ Birtles 1998, p. 67
  174. ^ Norris & Wagner 1999, pp. 152–156
  175. ^ "777-300 Technical Characteristics". Boeing. Retrieved March 20, 2009.
  176. ^ a b "Datafile: Boeing 777-300". Flug Revue. 2006. Archived from the original on January 30, 2008. Retrieved March 20, 2009.
  177. ^ a b c "Datafile: Boeing 777-300ER". Flug Revue. 2006. Archived from the original on January 29, 2008. Retrieved March 20, 2009.
  178. ^ a b c d e "Datafile: Boeing 777-200LR Worldiner". Flug Revue. 2006. Archived from the original on June 23, 2008. Retrieved March 20, 2009. {{cite web}}: |archive-date= / |archive-url= timestamp mismatch; May 17, 2008 suggested (help)
  179. ^ Field, David (March 17, 2008). "Delta pushes Boeing to squeeze more range from 777-200LR". Flight International. Retrieved December 2, 2008.
  180. ^ "FAA Type Certificate Data Sheet T00001SE" (PDF). Federal Aviation Administration. Retrieved November 5, 2009.
  181. ^ "Deliveries". Boeing. Retrieved September 8, 2009.
  182. ^ a b Eisenstein, Paul (July 2004). "Biggest Jet Engine". Popular Mechanics. Retrieved June 3, 2011.
  183. ^ Norris, Guy (January 2003). "Long Ranger". Flight International. Retrieved December 2, 2008.
  184. ^ Cheung, Clare (November 8, 2007). "Cathay Pacific Orders 17 Boeing Jets". Bloomberg. Retrieved December 2, 2008. {{cite web}}: Unknown parameter |coauthors= ignored (|author= suggested) (help)
  185. ^ Thomas, Geoffrey. "Boeing nose ahead in Qantas order race". The Australian, December 2, 2005. Retrieved: March 20, 2009.
  186. ^ "New Boeing 777-300ER Joins Air France Fleet" (PDF). Air France. May 13, 2004. Retrieved August 25, 2013.
  187. ^ Kingsley Jones, Ben (November 29, 2005). "Enhanced A340 to take on 777". Flight International. Retrieved April 2, 2009. {{cite web}}: Unknown parameter |coauthors= ignored (|author= suggested) (help)
  188. ^ Norris, Guy (May 16, 2006). "Cargo Kings: new Boeing 777F and 747-8F programmes". Flight International. Retrieved March 29, 2009.
  189. ^ Wallace, James (November 15, 2004). "Boeing seeks cargo 777 orders". Seattle Post-Intelligencer. Retrieved December 3, 2008.
  190. ^ "Air France to buy Boeing 777 freighters". USA Today. Associated Press. March 25, 2005. Retrieved October 19, 2010.
  191. ^ Sobie, Brendan (September 23, 2008). "Boeing reveals cargo conversion development studies for 777". Air Transport Intelligence via Flightglobal.com. Retrieved October 19, 2010.
  192. ^ Sobie, Brendan (October 19, 2010). "Boeing expects to secure 777BCF launch customer in early 2011". Air Transport Intelligence via Flightglobal.com. Retrieved October 19, 2010.
  193. ^ a b c "Boeing To Make Up Lost Grounds On All Fronts". Aspire Aviation. Retrieved June 20, 2013.
  194. ^ a b c "Boeing Launches 777X In Dubai Order Boom". Aviation Week. Retrieved November 17, 2013.
  195. ^ Sachdev, Ameet (September 27, 2006). "Boeing adds 777 to tanker mix". Chicago Tribune. Retrieved May 8, 2011.
  196. ^ Norris, Guy (October 3, 2006). "US Air Force tanker RFP reveals KC-777 offer". Flight International. Retrieved April 21, 2009.
  197. ^ "Ready to fill 'er up" (PDF). Boeing. November 2006. Retrieved April 21, 2009.
  198. ^ Vandruff, Ken (April 11, 2007). "Boeing submits KC-767 tanker proposal". Wichita Business Journal. Retrieved March 20, 2009.
  199. ^ Gale, Ivan (July 19, 2010). "Emirates $9bn deal beats expectations". The National. Retrieved March 3, 2012.
  200. ^ "World Airliner Census". Flightglobal Insight, September 12, 2013.
  201. ^ "Current Year Deliveries". Boeing. December 2013. Retrieved January 10, 2014.
  202. ^ "Orders and Deliveries search page". Boeing. December 2013. Retrieved January 10, 2014.
  203. ^ "Boeing Launches 777X with Record-Breaking Orders and Commitments". Boeing. November 2013. Retrieved December 23, 2013.
  204. ^ "Boeing and Cathay Pacific Airways Announce Order for 21 777-9Xs". Boeing. December 2013. Retrieved December 23, 2013.
  205. ^ a b c "Safety Recommendation: In reply refer to: A-09-17 (Urgent) and −18". Mayday, Discovery Channel. March 11, 2009.
  206. ^ "Boeing 777 occurrences". Aviation Safety Network. July 6, 2013. Retrieved July 6, 2013.
  207. ^ "Boeing 777 hull losses". Aviation Safety Network. July 6, 2013. Retrieved July 6, 2013.
  208. ^ "Boeing 777 Accident Statistics". Aviation Safety Network. July 6, 2013. Retrieved July 6, 2013.
  209. ^ a b "British Airways Flight 2019 ground fire". Aviation Safety Network. Retrieved November 21, 2008.
  210. ^ "DEN01FA157 entry". National Transportation Safety Board. February 24, 2005. Retrieved January 2, 2011.
  211. ^ "Interim Management Statement". British Airways. February 1, 2008. Retrieved November 21, 2008.
  212. ^ "Report on the accident to Boeing 777-236ER, G-YMMM, at London Heathrow Airport on 17 January 2008" (PDF). Air Accidents Investigation Branch. February 9, 2010. Retrieved February 9, 2010.
  213. ^ "'High risk' of plane fault repeat". BBC News. March 13, 2009. Retrieved March 20, 2009.
  214. ^ Woodman, Peter (February 9, 2010). "Ice 'probable cause' of Heathrow crash-landing". The Independent. UK. Retrieved December 11, 2011.
  215. ^ Kaminski-Morrow, David (February 29, 2008). "American investigates as 777 engine fails to respond to throttle". Flight International. Retrieved March 20, 2009.
  216. ^ "NTSB Investigates B777 Uncommanded Engine Rollback". Air Safety Week. December 22, 2008. Retrieved April 2, 2009.
  217. ^ a b c d "EgyptAir Flight 667 ground fire". Aviation Safety Network. Retrieved January 2, 2012.
  218. ^ a b "Recent Incidents / Accidents Worldwide". Jet Airliner Crash Data Evaluation Centre. July 2011. Retrieved January 2, 2012.
  219. ^ "One Asiana victim killed by a vehicle, not plane crash - coroner". Reuters News Agency. July 20, 2013. Retrieved August 8, 2013.
  220. ^ "3rd fatality in Asiana flight crash". CBS News. July 12, 2013. Retrieved July 14, 2013.
  221. ^ "Asiana 777-200ER crashes at San Francisco airport". Flight International. July 6, 2013. Retrieved July 6, 2013.
  222. ^ "Pilot Error Eyed in San Francisco Plane Crash". Wall Street Journal. July 8, 2013. Retrieved July 8, 2013. National Transportation Safety Board Chairman Deborah Hersman's comments indicated investigators were focused primarily on why the cockpit crew allowed speed to decay to such an extent ...
  223. ^ a b "Boeing 777X To Spark Mini-Jumbo War". Aspire Aviation. Retrieved June 20, 2013.
  224. ^ a b "777 Characteristics". Boeing. Retrieved October 10, 2012.
  225. ^ "777X Airport Combatibility" (PDF). July 2013. Retrieved November 18, 2013.
  226. ^ "Boeing's 777-9X comes into focus with a massive CFRP wing". October 31, 2011. Retrieved June 30, 2013.
  227. ^ "777 payload-range capability" (PDF). Boeing. 2009. Retrieved October 29, 2012.
  228. ^ "777 Airplane Characteristics for Airport Planning". Boeing. May 2011. Retrieved October 9, 2011.
  229. ^ Frawley 2003, pp. 61–62
  230. ^ "Trent 800 Technical data (archive)". Rolls-Royce. 2007. Archived from the original on October 26, 2007. Retrieved May 23, 2009.
  231. ^ "Stretched potential for Boeing 777". Flight Global. 2013. Retrieved October 16, 2013.

References

  • Abarbanel, Robert; McNeely, William (1996). FlyThru the Boeing 777. New York: ACM SIGGRAPH. ISBN 0-89791-784-7. {{cite book}}: Invalid |ref=harv (help)
  • Birtles, Philip (1998). Boeing 777, Jetliner for a New Century. St. Paul, Minnesota: Motorbooks International. ISBN 0-7603-0581-1. {{cite book}}: Invalid |ref=harv (help)
  • Birtles, Philip (1999). Modern Civil Aircraft: 6, Boeing 757/767/777 (Third ed.). London: Ian Allen Publishing. ISBN 0-7110-2665-3. {{cite book}}: Invalid |ref=harv (help)
  • Eden, Paul, ed. (2008). Civil Aircraft Today: The World's Most Successful Commercial Aircraft. London: Amber Books Ltd. ISBN 1-84509-324-0. {{cite book}}: Invalid |ref=harv (help)
  • Frawley, Gerard (2003). The International Directory of Civil Aircraft 2003/2004. London: Aerospace Publications. ISBN 1-875671-58-7. {{cite book}}: Invalid |ref=harv (help)
  • Glenday, Craig (2007). Guinness World Records. London/New York: HiT Entertainment. ISBN 978-0-9735514-4-0. {{cite book}}: Invalid |ref=harv (help)
  • Newhouse, John (2008). Boeing versus Airbus: The Inside Story of the Greatest International Competition in Business. London: Vintage. ISBN 1-4000-7872-5. {{cite book}}: Invalid |ref=harv (help)
  • Norris, Guy; Wagner, Mark (1996). Boeing 777. St. Paul, Minnesota: Motorbooks International. ISBN 0-7603-0091-7. {{cite book}}: Invalid |ref=harv (help)
  • Norris, Guy; Wagner, Mark (2001). Boeing 777: The Technological Marvel. Minneapolis, Minnesota: Zenith Imprint. ISBN 0-7603-0890-X. {{cite book}}: Invalid |ref=harv (help)
  • Norris, Guy; Wagner, Mark (2009). Boeing 787 Dreamliner. Osceola, Wisconsin: Zenith Press. ISBN 978-0-7603-2815-6. {{cite book}}: Invalid |ref=harv (help)
  • Norris, Guy; Wagner, Mark (1999). Modern Boeing Jetliners. Minneapolis, Minnesota: Zenith Imprint. ISBN 0-7603-0717-2. {{cite book}}: Invalid |ref=harv (help)
  • Sabbagh, Karl (1995). 21st Century Jet: The Making of the Boeing 777. New York: Scribner. ISBN 0-333-59803-2. {{cite book}}: Invalid |ref=harv (help)
  • Wells, Alexander T.; Rodrigues, Clarence C. (2004). Commercial Aviation Safety. New York: McGraw-Hill Professional. ISBN 0-07-141742-7. {{cite book}}: Invalid |ref=harv (help)
  • Yenne, Bill (2002). Inside Boeing: Building the 777. Minneapolis, Minnesota: Zenith Press. ISBN 0-7603-1251-6. {{cite book}}: Invalid |ref=harv (help)
Wikimedia Commons has media related to Boeing 777.

Template:Link GA Template:Link GA Template:Link GA

Retrieved from "https://en.wikipedia.org/enwiki/w/index.php?title=Boeing_777&oldid=592295132"