Jump to content

Serial Attached SCSI

From Wikipedia, the free encyclopedia

This is an old revision of this page, as edited by Neonetizen (talk | contribs) at 09:39, 24 August 2006. The present address (URL) is a permanent link to this revision, which may differ significantly from the current revision.

You must add a |reason= parameter to this Cleanup template – replace it with {{Cleanup|June 2006|reason=<Fill reason here>}}, or remove the Cleanup template.

Serial Attached SCSI (SAS) is a serial communication protocol for direct attached DAScomputer storage devices. It is designed for the corporate and enterprise market as a replacement for parallel SCSI, allowing for much higher speed data transfers than previously available, and is backwards-compatible with SATA. Though SAS uses serial communication instead of the parallel method found in traditional SCSI devices, it still uses SCSI commands for interacting with SAS End devices.

Introduction

The Serial Attached SCSI system consists of 3 basic components:

  • Initiators (the hosts which will use the system),
  • Expanders, and
  • Targets (disk arrays).

Initiators may be provided as an on board component of the motherboard (as is the case with many server-oriented motherboards) or through the use of an add-on host bus adapter.

The sum of all devices used in an SAS implementation is known as the "SAS Domain". This is merely a term to refer to the network of devices and corresponding World Wide Name (WWN). The World Wide Name is a globally unique identifier assigned to a device manufacturer (similar to that of an Ethernet device's MAC address). A SAS domain may contain up to a total of 16,256 devices.

Technical details

SAS supports point data transfer speeds up to 3 Gbit/s, but is expected to reach 10 Gbit/s by the year 2010. The SAS connector is much smaller than traditional parallel SCSI connectors allowing for the small 2.5 inch drives.

The physical SAS connector is available in several different variants including:

  • SFF 8482 — which is form factor compatible with SATA,
  • SFF 8484 — hi-density internal connector for connecting up to 4 devices,
  • SFF 8470 — hi-density external connector (aka Infiniband connector, also used as an internal connector) for connecting up to 4 devices.
  • SFF 8087 - Molex iPASS reduced width internal 4x connector with future 10 Gbit/s support
  • SFF 8088 - Molex iPASS reduced width external 4x connector with future 10 Gbit/s support

Form factor compatibility with SATA allows for much cheaper SATA drives to connect to a SAS backplane. SAS drives are not compatible on a SATA bus and have their physical connector keyed to prevent any plugging into a SATA backplane.

Serial Attached SCSI supports three transport protocols:

  • Serial SCSI Protocol (SSP) — Supporting SAS disk drives.
  • Serial ATA Tunneling Protocol (STP) — Supporting SATA disks.
  • Serial Management Protocol (SMP) — for managing SAS Expanders.

A SAS domain is a set of SAS ports communicating with each other. A SAS domain contains one or more SAS devices and a service delivery sub-system. A SAS domain may be a SCSI domain. Each SAS device is assigned a World Wide Name (aka SAS address) assigned by IEEE for the particular vendor. The WWN uniquely identifies the device in the SAS domain just as a SCSI ID identifies a device in a parallel SCSI bus.

Topology

Within a complex SAS domain, initiators are connected to edge expanders. Edge expanders may be connected to targets or a fanout expander. Fanout expanders may be connected to any combination of initiators, edge expanders, and targets. Each expander (Edge or Fanout) may connect to 128 other devices, though edge expanders may only connect to one other expander. Fanout expanders may connect any number of other edge expanders up to the 128 device limit. Another important note is that there may only be one Fanout expander within an SAS domain.

See also

External references

Retrieved from "https://en.wikipedia.org/enwiki/w/index.php?title=Serial_Attached_SCSI&oldid=71565078"