Jump to content

Metrology

From Wikipedia, the free encyclopedia

This is an old revision of this page, as edited by Palica (talk | contribs) at 11:52, 9 September 2006 (robot Adding: no:Metrologi, sk:Metrológia). The present address (URL) is a permanent link to this revision, which may differ significantly from the current revision.

Metrology (from greek 'metron' (measure), and -logy) is the science of measurement. Metrology includes all theoretical and practical aspects of measurement.

It is a field of study which has been highly politicized and nationalized with sharp even severe rhetoric as the field progressed.

Introduction

Metrology is defined by the International Bureau of Weights and Measures (BIPM) as "...the science of measurement, embracing both experiment and theoretical determinations at any level of uncertainty in any field of Science and Technology." [1]

Metrology regarded overall is a very broad field and may be be divided into three subfields:

  • Scientific or fundamental metrology, concerns the establishment of measurement units, unit systems, the development of new measurement methods, realisation of measurement standards and the transfer of traceability from these standards to users in society.
  • Applied or industrial metrology, concerns the application of measurement science to manufacturing and other processes and use in society, ensuring the suitability of measurement instruments, their calibration and quality control of measurements.
  • Legal metrology, concerns regulatory requirements of measurements and measuring instruments for the protection of health, public safety, the environment, enabling taxation, protection of consumers and fair trade.

A core concept in metrology is (metrological) traceability, defined() as "…the property of the result of a measurement or the value of a standard whereby it can be related to stated references, usually national or international standards, through an unbroken chain of comparisons, all having stated uncertainties." The level of traceability establishes the level of comparability of the measurement: whether the result of a measurement can be be compared to the previous one, a measurement result a year ago, or to the result of a measurement performed anywhere else in the whole world.

Traceability is most often obtained by calibration, establishing the relation between the indication of a measuring instrument and the value of a measurement standard.

An integral part of establishing traceability is evaluation of measurement uncertainty.

Historical development

Metrology has existed in some form or another since antiquity. The earliest forms of metrology were simply arbitrary standards set up by regional or local authorities, often based on practical measures such as the length of an arm (or part thereof). The earliest examples of these standardized measures are length, time, and weight. These standards were established in order to facilitate commerce and record human activity.

Little progress was made with regard to proto-metrology until various scientists, chemists, and physicists started making headway during the Scientific Revolution. With the advances in the sciences, the comparison of experiment to theory required a rational system of units, and something more closely resembling modern metrology began to come into being. The discovery of atoms, electricity, thermodynamics, and other fundamental scientific principles could be applied to standards of measurement, and many inventions made it easier to quantitatively or qualititatively assess physical properties, using the defined units of measurement established by science.

Metrology was thus one of the precursors to the Industrial Revolution, and was necessary for the implementation of mass production, equipment commonality, and assembly lines.

Modern metrology has its roots during the French Revolution, with the political motivation to harmonize units all over France and the concept of establishing units of measurement based on constants of nature, and thus making measurement units available "for all people, for all time". In this case deriving a unit of length from the dimensions of the Earth, and a unit of mass from a cube of water. The result was two platinum standards for the meter and the kilogram established as the basis of the metric system on June 22, 1799. This furhter led to the creation of the Système International d'Unités, or the International System of Units. This system has gained unprecedented worldwide acceptance as definitions and standards of modern measurement units. Though not the official system of units of all nations, the definitions and specifications of SI are globally accepted and recognized. The SI is maintained under the auspices of the Metre Convention and its institutions, the General Conference on Weights and Measures, or CGPM, it executive branch the International Committee for Weights and Measures, or CIPM, and its technical institution the International Bureau of Weights and Measures, or BIPM.

As the authorities on SI, these organizations establish and promulgate the SI, with the ambitition to be able to service all . This includes introducing new units, such as the relatively new unit, the mole, to encompass metrology in chemistry. These units are then established and maintained through various agencies in each country, and establish a hierarchy of measurement standards that can be traced back to the established standard unit, a concept known as metrological traceability. The U.S. agencies holding this responsibility is known as the National Institute of Standards and Technology, or NIST; and the American National Standards Institute, or ANSI.

Mechanisms of metrology

At the base of metrology is the definition, realisation and dissimination of units of measurement. Physical or chemical properties are quantised by assigning a property value in some multiple of a measurement unit.

The basic 'lineage' of measurement standards are:

1. The definition of a unit, based on some physical constant, such as absolute zero, the freezing point of water, etc; or an agreed-upon arbitrary standard.

2. The realisation of the unit by experimental methods and the scaling into multiples and submultiples, by establishment of primary standards. In some cases an approximation is used, when the realisation of the units is less precise than other methods of generating a scale of the quantity in question. This is presently the situation for the electrical units in the SI, where voltage and resistance are defined in terms of the ampere, but are used in practice from realisations based on the Josephson effect and the quantised Hall effect.

3. the transfer of traceability from the primary standards to secondary and working standards. This is achieved by calibration.

Theoretically, metrology, as the science of measurement, attempts to validate the data obtained from test equipment. Though metrology is the science of measurement, in practical applications, it is the enforcement and validation of predefined standards for precision, accuracy, traceability, and reliability. These standards can vary widely, but are often mandated but governments, agencies, and treaties such as the International Organization for Standardization, the Metre Convention, or the FDA. These agencies promulgate policies and regulations that standardize industries, countries, and streamline international trade, products, and measurements. Metrology is, at its core, an analysis of the uncertainty of individual measurements, and attempts to validate each measurement made with a given instrument, and the data obtained from it. The dissemination of traceability to consumers in society is often performed by dedicated calibration laboratory with a recognized quality system in compliance with such standards. National laboratory accreditation schemes have been established to offer third-party assessment of such quality systems. A central requirement of these accreditations is documented traceability to national or international standards.

Some common standards include:
ISO 17025:2005 - General Requirements for Calibration Laboratories
ISO 9000 - Quality Systems Management
ISO 14000 - Environmental Management
21 CFR Part 210/211 - FDA Regulations concerning GMP (Good Maintenance Practices) Quality Systems
21 CFR Part 110 - FDA Regulations concerning Food Industry GMP's

References

Retrieved from "https://en.wikipedia.org/enwiki/w/index.php?title=Metrology&oldid=74702007"