Jump to content

Arado E.583

From Wikipedia, the free encyclopedia

This is an old revision of this page, as edited by Blight609 (talk | contribs) at 01:58, 5 November 2018 (cl). The present address (URL) is a permanent link to this revision, which may differ significantly from the current revision.

Arado E.583
General information
TypeNight fighter aircraft project
ManufacturerArado Flugzeugwerke
History
Manufactured–
Introduction date–

The Arado E.583 was a project design from 1945 for a jet-powered night fighter aircraft of the German manufacturer Arado Flugzeugwerke.

History

The design of the E.583 goes back to the E.581, an earlier project by Arado, in which design variants for a single-beam, brushless (without tailplane) night fighter were also examined. The starting point for the E.581 was again the studies in connection with the project E.555 for a multi-beam long-range bomber. However, due to the long inlet and the large hull surface, the Heinkel HeS-011 jet engine of the E.581, which was integrated into the fuselage, could only expect inadequate performance in the high-speed sector.

Then Arado created two new project designs in accordance with the guidelines issued in January 1945 for the optimal solution of a night fighter. Under the overall designation E.583, the studies Ar-I and Ar-II - also referred to as Project I and II - were presented at the same time.

The Ar-I leaned on the draft E.581-5, but had much larger dimensions. The experts criticized on 20./21. March 1945 again the resistance generating engine intakes and large surfaces. Arado then improved the design so that a third crew member and a larger amount of fuel could be recorded. A third variant received smaller and more swept wings. Allegedly, it is said to have served as inspiration for the US Vought F7U-3 Cutlass. However, head of the aerodynamic research department of Vought, William C. Schoolfield, denied that any orientation towards German research has taken place. [1]

The Ar-II was an easier to implement alternative night and bad weather hunter. The design had swept wings and was strongly based on the Arado Ar 234 and the study TEW 16 / 43-23. The maximum speed was calculated at 775 km / h, lower than that of the Ar-I.

Construction

The Ar I was designed as a brushless aircraft, in which the ailerons also served as horizontal stabilizer. The two rudders were each placed on top of the wings.

Technical Data

Data from Arado E.583

General characteristics

  • Crew: Two
  • Length: 12.95 m (42 ft 6 in)
  • Wingspan: 18.38 m (60 ft 4 in)
  • Swept wingspan: 35 m (114 ft 10 in) swept
  • Max takeoff weight: 24,000 kg (52,911 lb)
  • Powerplant: 2 × He-S011 semi-hulled jet engines

Performance

  • Maximum speed: 810 km/h (500 mph, 440 kn)
  • Range: 3,600 km (2,200 mi, 1,900 nmi) with 2,000 kg (4,400 lb) bomb load
  • Service ceiling: 13 m (43 ft)

Armament

  • Guns:
    • Two MK 213/30 machine guns in the fuselage nose and two as rear armament
    • two MK 108 as oblique armament

[2][3]

See also

List of aircraft types

References

  1. ^ Jim Winchester: F7U Cutlass. International Air Power Review Vol. 15, S. 100.
  2. ^ Heinz J. Nowarra (1993) (in German), Die deutsche Luftrüstung 1933–1945, Koblenz: Bernard & Graefe Verlag, ISBN 3-7637-5464-4 
  3. ^ Dan Johnson: Ar I auf luft46.com, abgerufen am 28. Januar 2010
Retrieved from "https://en.wikipedia.org/enwiki/w/index.php?title=Arado_E.583&oldid=867329322"